Chriss
1 August 2026 17:1601.08.2026 17:16
Hello,
My EVO with Interbus is constantly displaying Interbus errors.
The motor is OK; insulation test performed.
The Interbus cable is approximately 45cm long.
The BEC runs at 8V.
What is the source of that?
Does it make sense to insert a ferrite core into the bus line?
Thank you very much
Kind regards
Edited once. Last edited on 01/08/2026 at 17:20 by Chriss. | - ezyZip(6).zip (1019 bytes)
Hallo,
bei meiner EVO mit Interbus kommen Ständig Interbus fehler.
Der Motor ist OK Isolationstest gemacht.
Die interbus leitung ist ca. 45cm lang.
BEC läuft auf 8V.
Was ist da die Quelle ?
Macht es sinn einen Ferrittkern in die Busleitung zu hängen ?
Dankeschön
Freundlicher Gruß
1 mal bearbeitet. Zuletzt am 01.08.2026 17:20 von Chriss.
| -
ezyZip(6).zip
(1019 bytes)
RV
1 August 2026 19:3901.08.2026 19:39
How is the Interbus configured?
What is used as the counterpart?
How is the Interbus and Master/Slave system connected?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 01.08.2026 19:39 von RV.
Wie ist der Interbus konfiguriert?
Was wird als Gegenstelle verwendet?
Wie ist der Interbus und Master/Slave an sich verbinden?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 01.08.2026 19:39 von RV.
Chriss
2 August 2026 01:3002.08.2026 01:30
Hello Rainer,
Here is the information
Interbus is configured as a master/slave system.
Both EVOs have the latest firmware.
Master Flight Hardware 10A BEC from regulator.
Slave Hardware: 5 servos, 3x LED lights for gating gun, 70 LEDs for turbine outlet via Unilight, 1 LED for headlight, 1x Benedini sound module, 1x 100W audio amplifier.
It is powered via a separate BEC.
Kind regards
Kind regards.
Hallo Rainer,
anbei die Infos
Interbus ist als Master/Slave koniguriert.
Es sind beide EVOs mit aktu.Firmware.
Master Flight Hardware 10A BEC vom Regler.
Slave Hardware: 5 Servos 3x Led Licht für Gating Gun. 70 Leds für Turbinenauslass über Unilight 1Led für Schwinwerfer. 1x Benedini Sound Modul. 1x 100W Nf-Verstärker.
Wird über extra BEC versorgt.
Freundlicher Gruß
Freundlicher Gruß.
RV
2 August 2026 09:5102.08.2026 09:51
Quote: Interbus is configured as a master/slave system.
What update rate is set?
Is AUX3 connected, or AUX2 and AUX3?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:Interbus ist als Master/Slave koniguriert.
Welche Updaterate ist eingestellt?
Ist AUX3 oder AUX2 und AUX3 verbunden?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Chriss
3 August 2026 07:1603.08.2026 07:16
It is connected via Aux3.
Where do I set the update rate via Interbus?
Kind regards
Es ist über Aux3 verbunden.
Wo stelle ich die update Rate über interbus ein ?
Freundlicher Gruß
Eddi E. aus G.
3 August 2026 09:2503.08.2026 09:25
Good morning,
Where do I set the update rate via Interbus?
Model Setup / Macro Cell Setup / Input/Output Configuration ...
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
> Wo stelle ich die update Rate über interbus ein ?
Modell Setup / Makrozellen Setup / Ein/Ausgangskonfiguration ...
Grüßle
Eddi
Born to fly ...
forced to work.
Chriss
3 August 2026 12:1003.08.2026 12:10
AUX 1/TELE 1+2 as AUX/Tele 1+2 Normal
Update rate AUX1 output. Milliseconds. 0
AUX 3 as an extender bus for slave
Kind regards
AUX 1/TELE 1+2 als AUX/ Tele 1+2 Normal
Updaterate AUX1 Ausgang. Millisec. 0
AUX 3 als Extender Bus für Slave
Freundlicher Gruß
Eddi E. aus G.
3 August 2026 12:5203.08.2026 12:52
Hi,
0 ... really?
The value range is 5 ... 30 ms, or 200 Hz ... 33 Hz.
20 would be standard, 50 Hz.
Grüßle
Eddi
Born to fly ...
forced to work.
Huhu,
0 ... echt?
Der Wertebereich ist 5 ... 30 ms, oder 200 Hz ... 33 Hz.
20 wäre Standard, 50 Hz.
Grüßle
Eddi
Born to fly ...
forced to work.
Fingolf
3 August 2026 15:4203.08.2026 15:42
And is the slave also correctly flashed as an extender?
What happens if nothing else is connected, what happens with a short patch cable?
Und die Slave ist auch korrekt als Extender geflashed?
Was passiert wenn da sonst nix dranhängt, was passiert mit einem kurzen Patch Kabel?
Chriss
3 August 2026 16:1603.08.2026 16:16
Hello,
Attached is a screenshot.
Slave is correctly flashed as an extender; yes, everything works, but the errors occur when the motor and controller are active.
What protocol does Interbus use? Does it have built-in error correction?
Thank you very much
Kind regards
Edited once. Last edited on 03/08/2026 at 16:19 by Chriss.
Hallo,
anbei ein Scrennshot.
Slave ist auch korrekt als Extender geflashed, ja es geht ja alles nur wenn Motor und regler aktiv sind gibts die Fehler.
Was hat der Interbus für ein protokoll ? Hat das eine fehler-korrektur mit eingebaut ?
Dankeschön
Freundlicher Gruß
1 mal bearbeitet. Zuletzt am 03.08.2026 16:19 von Chriss.
Eddi E. aus G.
4 August 2026 08:5904.08.2026 08:59
Good morning,
...interesting. Perhaps something was loaded into the macrocells that wasn't actually macrocells or was somehow faulty?
There was a customer who had lobotomized his VBar by loading a log file into it using PC software to view it ^^
Save the macro cells in this way so that they end up in the cloud.
What happens if you manually set it to, for example, 20 ms?
I don't know the details, but as far as I know it's a CAN bus-like protocol, 2-channel (for NEO) and 1-channel (for EVO), and I think it will have at least one CRC.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
... spannend. Evtl. wurde da was in die Makrozellen geladen, was keine Makrozellen oder irgendwie fehlerbehaftet war?
Gab mal einen Kunden, der hatte seine VStabi lobotomiert, indem sie ein Log mittels PC-Software rein geladen hat, um es anzuschauen ^^
Speichere die Makrozellen mal so, damit sie in der Cloud landen.
Wie isses dann, wenn Du das jetzt händisch bspw. auf 20 ms stellst?
Im Detail weiß ich's nicht, aber es ist m. W. ein Can Bus-artiges Protokoll, 2-Kanal (bei NEO) und 1-Kanal (bei EVO), und es wird mindestens ein CRC drauf sein, denke ich.
Grüßle
Eddi
Born to fly ...
forced to work.
RV
4 August 2026 20:4204.08.2026 20:42
Okay - normally it says 20ms.
Please post that. However, I don't think that was it.
Quote: Yes, everything works, but the errors only occur when the motor and controller are active.
Then that's causing the problem. It might also be due to the second power supply being connected to the slave unit. Please try connecting it "normally," including the positive connection and removing the second BEC.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Okay - normal steht da 20ms drin.
Bitte das mal einstellen. Allerdings glaube ich nicht dass es das war.
Quote:ja es geht ja alles nur wenn Motor und regler aktiv sind gibts die Fehler.
Dann stört das halt ein. Ev. kommts auch davon dass hier eine 2. Spannungsversorgung am Slave dran ist. Bitte mal "normal" anschließen incl. Plus und 2. Bec wegmachen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Chriss
5 August 2026 06:3905.08.2026 06:39
Hello,
So the setup/macro is in the cloud.
Thank you. Kind regards.
Hallo,
also das Setup/Macro ist in der Cloud.
Dankeschön Freundlicher Gruß
Eddi E. aus G.
5 August 2026 09:2405.08.2026 09:24
Good morning,
The 0s are in the macrocell file; I just loaded both onto a stabilization system.
KP where from or why. When you tap the selection, only the value range is displayed, and it's automatically set to 5.
Otherwise, please do as Rainer writes.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin,
die 0 sind im Makrozellen-File drin, hab beides gerade auf eine Stabi geladen.
KP woher oder warum. Wenn man die Auswahl antippt, wird nur der Wertebereich angezeigt, und automatisch auf 5 gesetzt.
Sonst mal bitte wie Rainer schreibt.
Grüßle
Eddi
Born to fly ...
forced to work.
Chriss
5 August 2026 12:3105.08.2026 12:31
Hello,
If I change the value to 0, the smallest value displayed is 5.
Possibly a bug?
Friendly greetings
Hallo,
wenn ich einmal den wert also die 0 ändere steht dann als kleinster wert 5 drin.
Evtl. ein Bug ?
Fraundlicher Gruß
Eddi E. aus G.
5 August 2026 13:1405.08.2026 13:14
No, that's how it's supposed to be.
Default (new setup, macro cells deleted) = 20
Adjustable from 5 to 30, but _not_ 0.
That's what I'm wondering, where did the 0 come from?
And why is it adjustable? Other digital devices can also be connected to AUX1, e.g., S.BUS or UDI-compatible devices or those with a spectrum input, and these may even be able to handle higher rates, or only function reliably at lower rates.
Grüßle
Eddi
Born to fly ...
forced to work.
Nee, das soll ja so sein.
Standard (neues Setup, Makrozellen gelöscht) = 20
Einstellbar von 5 ... 30, aber eben _nicht_ 0.
Das ist ja das, was ich mich frage, woher kam die 0?
Und warum ist es einstellbar? An AUX1 können ja auch andere digitale Geräte hängen, bspw. S.BUS- oder UDI-kompatible oder welche mit Spektrum-Eingang, und die können ggfs. sogar höhere Raten, oder funktionieren nur mit niedrigeren zuverlässig.
Grüßle
Eddi
Born to fly ...
forced to work.
RV
5 August 2026 13:3405.08.2026 13:34
Simply doing what we write instead of discussing it would also be a step in the right direction... it could lead to some insights ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Einfach mal machen was wir schreiben statt zu diskutieren wäre auch eine Maßnahme ... könnte zu Erkenntnissen führen ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.