I recently replaced the NEO in my OYX 5 MEG with the EVO (still V7), more out of curiosity than necessity. Except for certain issues with the rear, I had a really well-functioning system with the NEO.
Current setup as follows:
• Motor: Xnova 4025 670KV
• Controller: YGE Sapphire 155
• Batteries: BONKA 8S 5200mAh
• TS servos: AGF A80BHX-H with 1520µs
• Tail servo: AGF A80BHP-H with 760 µs
• Rotor blades: currently AZUR 600 / alternatively or previously Rotortech Ultimate 610
• Speeds: 1680 / 1860 / 2080
• Head damping: HHH (as recommended in the manual for my flying style and RPMs)
Before switching to the V8, I wanted to quickly find a decent setting with the V7 so I could also make a comparison with the NEO.
Now I'm already struggling with problems in version 7 that were actually only described in version 8.
Nodding:
I experience the rocking motion on all three cylinder banks. It's most pronounced at the lowest RPM, decreasing with increasing RPM, but always present.
During the switchover, I also followed the instructions at “vstabi.info/de/node/2458”.
Then sensitivities, optimizers on all banks, … etc.
I have now tweaked pretty much all parameters (sensitivity, integral, style, response) over a good dozen flights, but I haven't been able to eliminate the rocking.
Sensitivity: What I find curious is that I can't find a sensitivity setting where the helicopter starts shaking or oscillating excessively. I can set values from 0 to 120 across the entire RPM range without the helicopter becoming unflyable. Only the oscillation remains almost constant across the entire range. Overall, different settings are much less noticeable than on the NEO.
Integral: the situation is similar here; at 0 everything becomes very vague and the helicopter develops a slightly unpredictable life of its own on the roll.
However, the rocking motion will always remain!
Responsiveness: Reducing the setting to 45% allowed me to slightly improve the rocking motion.
Controller: As before, I'm flying with VBar Governor: With the controller (YGE Saphir 155) I currently have the frequency set to 144 Hz; 72 or 333 didn't make any difference either.
[/u]
Rear: Bounce / Lock: [u][/u]
The tail behaves very similarly to Nick, but only when yaw – stopping to the right. I was able to largely eliminate the bouncing afterward today with repeated optimization and adjustments to Stop Gain A/B, but the "locking" is more like "parking." (During the subsequent flight with a NEO on my Nimbus Nitro, the difference was more than noticeable.)
Here too, the possible sensitivity values are unusually high. Or is this really normal for the EVO?
Even at 2080 rpm, I can easily set it to 90 km/h without the tail even starting to whine. This was achieved using Daniel's method with overspeed. And even more is possible.
What other options/approaches are there to bring the pitching and locking of the rear end up to the level of the NEO?
*The same applies to other rotor blades (Rotortech Ultimate).
Edited once. Last edited on 14.06.2026 at 23:54 by Falo.
Current setup as follows:
• Motor: Xnova 4025 670KV
• Controller: YGE Sapphire 155
• Batteries: BONKA 8S 5200mAh
• TS servos: AGF A80BHX-H with 1520µs
• Tail servo: AGF A80BHP-H with 760 µs
• Rotor blades: currently AZUR 600 / alternatively or previously Rotortech Ultimate 610
• Speeds: 1680 / 1860 / 2080
• Head damping: HHH (as recommended in the manual for my flying style and RPMs)
Before switching to the V8, I wanted to quickly find a decent setting with the V7 so I could also make a comparison with the NEO.
Now I'm already struggling with problems in version 7 that were actually only described in version 8.
Nodding:
I experience the rocking motion on all three cylinder banks. It's most pronounced at the lowest RPM, decreasing with increasing RPM, but always present.
During the switchover, I also followed the instructions at “vstabi.info/de/node/2458”.
Then sensitivities, optimizers on all banks, … etc.
I have now tweaked pretty much all parameters (sensitivity, integral, style, response) over a good dozen flights, but I haven't been able to eliminate the rocking.
Sensitivity: What I find curious is that I can't find a sensitivity setting where the helicopter starts shaking or oscillating excessively. I can set values from 0 to 120 across the entire RPM range without the helicopter becoming unflyable. Only the oscillation remains almost constant across the entire range. Overall, different settings are much less noticeable than on the NEO.
Integral: the situation is similar here; at 0 everything becomes very vague and the helicopter develops a slightly unpredictable life of its own on the roll.
However, the rocking motion will always remain!
Responsiveness: Reducing the setting to 45% allowed me to slightly improve the rocking motion.
Controller: As before, I'm flying with VBar Governor: With the controller (YGE Saphir 155) I currently have the frequency set to 144 Hz; 72 or 333 didn't make any difference either.
[/u]
Rear: Bounce / Lock: [u][/u]
The tail behaves very similarly to Nick, but only when yaw – stopping to the right. I was able to largely eliminate the bouncing afterward today with repeated optimization and adjustments to Stop Gain A/B, but the "locking" is more like "parking." (During the subsequent flight with a NEO on my Nimbus Nitro, the difference was more than noticeable.)
Here too, the possible sensitivity values are unusually high. Or is this really normal for the EVO?
Even at 2080 rpm, I can easily set it to 90 km/h without the tail even starting to whine. This was achieved using Daniel's method with overspeed. And even more is possible.
What other options/approaches are there to bring the pitching and locking of the rear end up to the level of the NEO?
*The same applies to other rotor blades (Rotortech Ultimate).
Edited once. Last edited on 14.06.2026 at 23:54 by Falo.
Aktuell habe ich bei meinen OYX 5 MEG das NEO durch das EVO (noch V7) ersetzt, mehr aus Neugier, als dass es wirklich notwendig gewesen wäre. Bis auf gewisse Situationen beim Heck, hatte ich zuletzt ein wirklich sehr gut funktionierendes Paket mit dem NEO.
Nachfolgen aktuelles Setup:
• Motor: Xnova 4025 670KV
• Regler: YGE Saphir 155
• Akkus: BONKA 8S 5200mAh
• TS-Servos: AGF A80BHX-H mit 1520µs
• Heck-Servo: AGF A80BHP-H mit 760 µs
• Rotorblätter: aktuell AZUR 600 / alternativ bzw. zuvor Rotortech Ultimate 610
• Drehzahlen: 1680 / 1860 / 2080
• Kopf-Dämpfung: HHH (wie lt. Anleitung für meinen Flugstil und Drehzahlen empfohlen)
Bevor ich zur V8 wechsle, wollte ich erst mal (schnell) mit der V7 eine anständige Einstellung finden, um auch einen Vergleich mit dem NEO ziehen zu können.
Nun habe ich bereits in der V7 mit Problemen zu kämpfen, die eigentlich erst in der V8 beschrieben wurden.
Nickwippen:
Das Wippen habe ich auf allen 3 Bänken. In der niedrigsten Drehzahl am ausgeprägtesten, abnehmend mit den höheren Drehzahlen. Aber immer präsent.
Beim Umstieg bin auch nach “vstabi.info/de/node/2458“ vorgegangen.
Dann Empfindlichkeiten, Optimierer auf allen Bänken erfliegen, … usw.
Ich habe nun bei gut ein Dutzend Flügen so ziemlich an allen Parametern (Empfindlichkeit, Integral, Style, Ansprechverhalten) geschraubt aber das Wippen nicht beseitigen können.
Empfindlichkeit: das für mich nebenbei kuriose ist, dass ich bei der Empfindlichkeit wirklich keinen Wert einstellen kann, bei dem sich der Heli extrem anfängt zu schütteln oder aufzuschaukeln. Ich kann in allen Drehzahlbereichen Werte von 0 - 120 einstellen, ohne dass der Heli jetzt unfliegbar wird. Nur das Wippen bleibt über den gesamten Bereich annähernd konstant. Insgesamt machen sich unterschiedliche Werte wesentlich weniger bemerkbar als beim NEO.
Integral: hier verhält es sich ähnlich, bei 0 wird halt alles seeehr schwammig und der Heli bekommt doch ein leicht unberechenbares Eigenleben auf Roll.
Wie auch immer, das Wippen bleibt immer!
Ansprechverhalten: Mit dem Reduzieren auf 45 des konnte ich das Wippen minimal verbessern
Regler: Wie zuvor fliege ich mit VStabi Governor: Beim Regler (YGE Saphir 155) hab ich die Frequenz aktuell auf 144 Hz, 72 oder 333 brachten auch keine Veränderung.
[/u]
Heck: Nachwippen / Einrasten:[u][/u]
Ganz ähnlich wir bei Nick, verhält es sich beim Heck aber nur beim Gieren – Stoppen nach rechts. Das Nachwippen konnte ich heute mit wiederholtem Optimierer und Einstellungen bei Stop Gain A/B weitestgehend beseitigen aber das “Einrasten“ ist eher ein “Einparken“. (Beim anschließenden Flug mit einem NEO auf meinem Nimbus Nitro, war der Unterschied mehr als deutlich zu erkennen)
Auch hier ist sind die möglichen Werte für die Empfindlichkeit wirklich sehr ungewöhnlich hoch. Oder ist dies wirklich mit dem EVO so normal?
Selbst bei 2080 U/min kann ich absolut problemlos 90 einstellen, ohne dass das Heck anfängt zu wimmern. So erflogen nach Daniels Methode mit Overspeed. Und es wäre/ist noch mehr möglich.
Welche Möglichkeiten / Ansätze gibt es nun noch, um das Nickwippen* und Einrasten des Hecks auf das Niveau vom NEO zu bringen?
*Mit anderen Rotorblättern (Rotortech Ultimate) verhält es sich ebenso.
1 mal bearbeitet. Zuletzt am 14.06.2026 23:54 von Falo.
Nachfolgen aktuelles Setup:
• Motor: Xnova 4025 670KV
• Regler: YGE Saphir 155
• Akkus: BONKA 8S 5200mAh
• TS-Servos: AGF A80BHX-H mit 1520µs
• Heck-Servo: AGF A80BHP-H mit 760 µs
• Rotorblätter: aktuell AZUR 600 / alternativ bzw. zuvor Rotortech Ultimate 610
• Drehzahlen: 1680 / 1860 / 2080
• Kopf-Dämpfung: HHH (wie lt. Anleitung für meinen Flugstil und Drehzahlen empfohlen)
Bevor ich zur V8 wechsle, wollte ich erst mal (schnell) mit der V7 eine anständige Einstellung finden, um auch einen Vergleich mit dem NEO ziehen zu können.
Nun habe ich bereits in der V7 mit Problemen zu kämpfen, die eigentlich erst in der V8 beschrieben wurden.
Nickwippen:
Das Wippen habe ich auf allen 3 Bänken. In der niedrigsten Drehzahl am ausgeprägtesten, abnehmend mit den höheren Drehzahlen. Aber immer präsent.
Beim Umstieg bin auch nach “vstabi.info/de/node/2458“ vorgegangen.
Dann Empfindlichkeiten, Optimierer auf allen Bänken erfliegen, … usw.
Ich habe nun bei gut ein Dutzend Flügen so ziemlich an allen Parametern (Empfindlichkeit, Integral, Style, Ansprechverhalten) geschraubt aber das Wippen nicht beseitigen können.
Empfindlichkeit: das für mich nebenbei kuriose ist, dass ich bei der Empfindlichkeit wirklich keinen Wert einstellen kann, bei dem sich der Heli extrem anfängt zu schütteln oder aufzuschaukeln. Ich kann in allen Drehzahlbereichen Werte von 0 - 120 einstellen, ohne dass der Heli jetzt unfliegbar wird. Nur das Wippen bleibt über den gesamten Bereich annähernd konstant. Insgesamt machen sich unterschiedliche Werte wesentlich weniger bemerkbar als beim NEO.
Integral: hier verhält es sich ähnlich, bei 0 wird halt alles seeehr schwammig und der Heli bekommt doch ein leicht unberechenbares Eigenleben auf Roll.
Wie auch immer, das Wippen bleibt immer!
Ansprechverhalten: Mit dem Reduzieren auf 45 des konnte ich das Wippen minimal verbessern
Regler: Wie zuvor fliege ich mit VStabi Governor: Beim Regler (YGE Saphir 155) hab ich die Frequenz aktuell auf 144 Hz, 72 oder 333 brachten auch keine Veränderung.
[/u]
Heck: Nachwippen / Einrasten:[u][/u]
Ganz ähnlich wir bei Nick, verhält es sich beim Heck aber nur beim Gieren – Stoppen nach rechts. Das Nachwippen konnte ich heute mit wiederholtem Optimierer und Einstellungen bei Stop Gain A/B weitestgehend beseitigen aber das “Einrasten“ ist eher ein “Einparken“. (Beim anschließenden Flug mit einem NEO auf meinem Nimbus Nitro, war der Unterschied mehr als deutlich zu erkennen)
Auch hier ist sind die möglichen Werte für die Empfindlichkeit wirklich sehr ungewöhnlich hoch. Oder ist dies wirklich mit dem EVO so normal?
Selbst bei 2080 U/min kann ich absolut problemlos 90 einstellen, ohne dass das Heck anfängt zu wimmern. So erflogen nach Daniels Methode mit Overspeed. Und es wäre/ist noch mehr möglich.
Welche Möglichkeiten / Ansätze gibt es nun noch, um das Nickwippen* und Einrasten des Hecks auf das Niveau vom NEO zu bringen?
*Mit anderen Rotorblättern (Rotortech Ultimate) verhält es sich ebenso.
1 mal bearbeitet. Zuletzt am 14.06.2026 23:54 von Falo.
machine-translated from German · Show original