PMDirk
10 October 2026 17:1310.10.2026 17:13
I have a question for you.
I'm using a LOGO 480 mechanics system with VBar NEO and Savox SV 1261 MG HV servos on the swashplate in a scale helicopter with a head speed of 1500 rpm. The helicopter flies superbly without any bouncing or other issues.
I have now built another LOGO 480 mechanism, but this time with a modern VBar EVO.
Based on the aforementioned positive experience with the VBar NEO and Savox SV 1261 MG HV servos on the TS, I'm using the same Savox servos on my VBar EVO. The helicopter is (still) being used as a trainer with 500mm main rotor blades. Unfortunately, I can't eliminate the pitch oscillation after short pitch inputs, neither with V7 nor V8 servos and 1500 rpm at the rotor head.
I think the problem lies with the TS servos; I'd like to test a different set of TS servos. Which current HV midi servos would you recommend for the VBar EVO?
Thank you very much and best regards
Dirk
Ich hätte ein Frage an Euch.
Habe eine LOGO 480 Mechanik mit VStabi NEO und Savox HV Servos SV 1261 MG an der TS in einem Scale Heli mit 1500 rpm als Kopfdrehzahl im Einsatz. Der Heli fliegt super ohne Nachwippen etc.
Habe nun eine weitere LOGO 480 Mechanik aufgebaut, allerdings zeitgemäß mit einem VStabi EVO.
Aus der vorgenannten guten "VStabi NEO und Savox SV 1261 MG HV Erfahrung an der TS" habe ich die selben Savox Servos am VStabi EVO im Einsatz. Der Heli ist (noch) als Trainer mit 500er Hauptrotorblättern unterwegs. Aber leider bekomme ich das Nachwippen über Nick bei kurzen Nickimpulsen weder mit V7 noch mit V8 und 1500 rpm am Kopf nicht weg.
Ich denke es liegt an den TS-Servos, ich möchte nun gern einen anderen Satz TS-Servos testen. Welche aktuellen HV Midi-Servo´s wären eine Empfehlung für das VStabi EVO?
Vielen Dank und beste Grüße
Dirk
Max8200
10 October 2026 18:4110.10.2026 18:41
The KST X15-1809 servos work perfectly; if not, you can be sure it's not the servos' fault :-)
Best regards,
Lars
Mit den KST X15-1809 klappt das super, wenn nicht bist du sicher das es nicht an den Servos liegt :-)
Viele Grüße,
Lars
sme
11 October 2026 09:2111.10.2026 09:21
Hi Dirk,
Unfortunately, the Evo is difficult to adjust with older servos and away from high RPMs.
I've had this problem with several helicopters as well.
But it doesn't always have to be a servo replacement.
Depending on the model, the following helped me.
TDF: Sensitivity significantly increased to 230, then reduced back to 200 as recommended by Uli to remain within a safe range. Fine-tuning with stop support.
Kraken700: Direct drive percentage significantly reduced, followed by fine-tuning of steering behavior and stop support.
So it's possible without replacing the servo, but it involves a lot of adjustments and testing.
Best regards
Stefan
Hallo Dirk,
leider ist die Evo mit älteren Servos und Abseits hoher Drehzahlen schwierig einzustellen.
Ich hatte das Problem auch schon bei mehreren Helis.
Aber es muß nicht immer ein Servotausch sein.
Je nach Modell hat mir folgendes geholfen.
TDF: Empfindlichkeit deutlich erhöht bis auf 230 und dann nach Ulis Empfehlung wieder auf 200 gesenkt um im sicheren Bereich zu bleiben. Feintuning mit Stop Unterstützung
Kraken700: Direktanteil deutlich gesenkt und dann Feintuning mit Steuerverhalten und Stopunterstützung.
Ist also auch ohne Servotausch möglich, aber mit viel Einstellerei und testen verbunden.
Viele Grüße
Stefan
PMDirk
11 October 2026 14:4711.10.2026 14:47
Hello Lars and Stefan,
Thank you so much for your information.
@Stefan
I have already tried and tested many settings with the VBar EVO, but unfortunately I cannot get close to my "VBar NEO reference" described in the opening post.
Therefore, I would like to try other TS servos.
Regards, Dirk
Hallo Lars und Stefan,
vielen Dank für Eure Info´s.
@Stefan
Habe schon viele Einstellungen mit der VStabi EVO probiert und getestet, komme aber leider nicht an meine im Eröffnungspost beschriebene "VStabi NEO Referenz" heran.
Daher möchte ich andere TS-Servos probieren.
Gruß Dirk
Eddi E. aus G.
12 October 2026 09:2212.10.2026 09:22
Hi Dirk,
How do you approach it?
LOGO 480 Setup from the 'New Setup' card file?
Did you change anything else after that?
In my experience with support, I get the impression that the standard setups still work well.
However, if you then choose the [...] basic settings in V8, for example, things can go wrong because they may be too sensitive for 'more normal' servos (or simply not suitable for micro-helicopters like the 200 or Stratos, because the optimal value range is very narrow there...).
And at the TS, 144 Hz / 1,520 µs should be 'achieved', which is the same as with the NEO, which has 'always' been a good mathematical match for our speeds up to around 2,000 rpm.
If in doubt, please try the (standard setup) again, and then just experiment with maneuverability, steering behavior and sensitivity :-)
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Dirk,
wie gehst Du denn ran?
LOGO 480 Setup aus dem 'Neues Setup'-Karteikasten?
Hast Du dann schon noch was geändert?
Ich habe im Support das Gefühl, dass die Standard-Setups nach wie vor gut funktionieren.
Wenn man dann aber die [...] Grundeinstellungen in V8 bspw. wählt, geht's u. U. in die Hose, weil die für 'normalere' Servos u. U. schon zu scharf sind (oder auch zu Micro-Helis wie dem 200-er oder Stratos einfach nicht passen, weil da der optimale Wertebereich eben sehr schmal ist ...).
Und an der TS sollte mit 144 Hz / 1.520 µs 'geschafft' werden, das ist dann so wie bei der NEO, was ja 'schon immer' rechnerisch gut zu unseren Drehzahlen bis um die 2.000 1/min gepasst hat.
Im Zweifel bitte nochmal das (Standard-Setup), und dann erst mal nur mit Wendigkeit, Steuerverhalten und Empfindlichkeit 'spielen' :-)
Grüßle
Eddi
Born to fly ...
forced to work.
PMDirk
12 October 2026 20:2212.10.2026 20:22
Hi Eddi,
Thank you for your reply. That's certainly another approach, with a completely new standard setup under the V8. I'll test it again this weekend or soon.
Do you have any other recommendations/tips for current TS-Midi servos for the VBar EVO?
Regards, Dirk
Hallo Eddi,
vielen Dank für Deine Antwort. Das ist natürlich auch nochmal ein Ansatz, mit einem komplett neuen Standard Setup unter der V8. Werde ich am Wochenende bzw. demnächst nochmal testen.
Hättest Du ansonsten noch eine Empfehlung/Tipp für aktuelle TS-Midi Servos an der VStabi EVO?
Gruß Dirk
Eddi E. aus G.
13 October 2026 09:1713.10.2026 09:17
Hi Dirk,
Not really, because... a standard setup with minor adjustments to sensitivity/control behavior has always worked for me.
And I don't understand it the other way around either... I recently got my hands on a cheap Chinese drone about 200 size, with the built-in flight control and bus receiver 'adequate' and with some adjustment of maneuverability and expo 'satisfactory'.
Then I screwed on the ESC from our 200-size helicopter and an EVO micro ESC, leaving the 200-size setup as it was, only adjusting the trim and pitch, setting it to 8° by eye, and... it flies like a 200-size, 'good'. With some adjustments to sensitivity and control behavior, it even gets a 'good to very good' rating for what it is.
I think there are a lot of self-inflicted problems circulating :-) minus the courage to try something, or the idea, hey, if it doesn't work like this, I'll start all over again and approach it from the bottom up.
There will always be exceptions, and optimization is always possible, but in my experience, the rule is that it simply works as it is.
I'm curious to see your results!
Grüßle
Eddi
Born to fly ...
forced to work.
Hi Dirk,
eigentlich nicht, weil ... Standard-Setup mit kleinen Anpassungen Empfindlichkeit/Steuerverhalten hat für mich immer funktioniert.
Und anders rum verstehe ich's auch nicht ... ich hab die Tage einen China-Böller in etwa 200-er Größe in die Finger bekommen, mit der eingebauten Flight Control und Bus-Empfänger 'ausreichend' und mit etwas Nachjustieren von Wendigkeit und Expo 'befriedigend'.
Dann den Regler von unserem 200-er und eine EVO micro drauf gespaxt, das 200-er Setup so wie's war gelassen, nur Trimmung, Pitchwege, 8° nach besserem Augenmaß eingedreht, und ... fliegt wie ein 200-er, 'gut'. Mit etwas Anpassung Empfindlichkeit und Steuerverhalten gibt's sogar 'ne 'gut-sehr gut', für das was es ist.
Ich glaube, da sind viele selbst gemachte Probleme im Umlauf :-) minus dem Mut, mal was zu probieren, oder der Idee, hey, wenn's so nicht geht, fang ich nochmal von vorn an und taste mich von unten ran.
Ausnahmen wird's immer geben, und optimieren kann man auch immer, aber die Regel ist meiner Erfahrung nach, es funktioniert einfach so wie's ist.
Bin neugierig auf Deine Ergebnisse!
Grüßle
Eddi
Born to fly ...
forced to work.