Jurrien Saelens
7 October 2026 19:2207.10.2026 19:22
I see that there is now a Goosky S2 option for the EVO v8.2 in addition to the Stratos 200.
That's great, and I'd love to try it out. I have some JST-to-JR adapters for the servos, so that should work. However, I still need some information about the ESC.
The Goosky manual contains the following pin assignment:
GND - 5V - TAIL_MOTOR - MAIN_MOTOR - ESC_DATA
I have two questions about this:
1. Should ESC_DATA therefore be connected to the RPM input of the EVO?
2. Is there no telemetry like on the Stratos 200?
Ich sehe, dass es jetzt für den EVO v8.2 neben dem Stratos 200 auch eine Goosky-S2-Option gibt.
Das freut mich sehr, und ich würde das gerne ausprobieren. Ich habe einige JST-auf-JR-Adapter für die Servos, damit sollte es also funktionieren. Allerdings brauche ich noch ein paar Informationen zum ESC.
Im Goosky-Handbuch finde ich folgende Pinbelegung:
GND - 5V - TAIL_MOTOR - MAIN_MOTOR - ESC_DATA
Dazu habe ich zwei Fragen:
1. Soll ESC_DATA also an den RPM-Eingang des EVO angeschlossen werden?
2. Gibt es keine Telemetrie wie beim Stratos 200?
RV
7 October 2026 19:3007.10.2026 19:30
Hello Jurrien,
Goo-Sky received equipment (VBars and VBCs) from us as part of a cooperation agreement to adapt their helicopter controller.
This has indeed happened; my test controller here in the S2 works perfectly. Development is complete on our end. However, I suspect that Goo-Sky hasn't tested it much yet; there's been radio silence from them for several months.
However, this is NOT the standard controller they're currently selling. The hardware had to be modified (as you mentioned above...) to get RPM readings and maintain telemetry. That's not possible with your controller.
So if you want to know if and when the preset I created can be used with a corresponding controller or even a helicopter => ask Goo-Sky.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 07.10.2026 19:31 von RV.
Hallo Jurrien,
Goo-Sky hat von uns im Sinne einer Kooperation Equipment (VStabis und VBCs) bekommen um damit ihren Heliregler anzupassen.
Dies ist auch geschehen, mein Testregler hier im S2 geht prima. Die Entwicklung dazu ist von unserer Seite aus "durch". Ich befürchte allerdings dass Goo-Sky da noch nicht viel mit getestet hat, seit einigen Monaten ist hier Funkstille.
Allerdings ist das NICHT der im Moment von ihnen verkaufte Serienregler. Da musste die Hardware (du hast das oben schon angesprochen...) geändert werden um RPM herauszubekommen und die Telemtrie zu erhalten. Mit Deinem Regler geht das nicht.
Wenn Du also wissen willst ob und wann das von mir erstellte Preset mit entsprechendem Regler oder gar Heli nutzbar sein kann => Goo-Sky fragen.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 07.10.2026 19:31 von RV.
Jurrien Saelens
7 October 2026 19:3907.10.2026 19:39
It's a shame that it doesn't work with my current S2 MAX ESC.
Thank you so much for the quick reply! I hope Goosky releases the version you have soon. Thank you!
Schade, dass es mit meinem aktuellen S2 MAX ESC nicht funktioniert.
Vielen Dank für die schnelle Antwort! Ich hoffe, Goosky bringt die Version, die du hast, bald auf den Markt. Vielen Dank!
Jurrien Saelens
7 October 2026 19:4507.10.2026 19:45
Just to clarify: Would it work without an RPM signal and telemetry?
So, only with the signals for the rear and main motors, or does Goosky use a proprietary DSHOT variant?
Nur zur Klarstellung: Würde es ohne RPM-Signal und Telemetrie funktionieren?
Also nur mit den Signalen für Heck- und Hauptmotor, oder verwendet Goosky eine proprietäre DSHOT-Variante?
RV
7 October 2026 20:3507.10.2026 20:35
Honest answer:
I have no idea, I've never tested that.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Ehrliche Antwort:
Keine Ahnung, das habe ich nie getestet.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jurrien Saelens
12 October 2026 14:2812.10.2026 14:28
I just tested the main motor and the tail motor with your Goosky S2 Mx settings on the workbench without rotor blades.
It seems to work, at least on the workbench.
The main motor responds to the three banks.
The rear engine is also running.
I haven't yet tried the connection between RPM or telemetry and ESC_DATA.
Do you think I could damage something in the process?
Ich habe gerade den Hauptmotor und den Heckmotor mit deinen Goosky S2 Mx-Einstellungen auf der Werkbank ohne Rotorblätter getestet.
Es scheint zu funktionieren, zumindest auf der Werkbank.
Der Hauptmotor reagiert auf die drei Bänke.
Der Heckmotor läuft auch.
Die Verbindung zwischen RPM oder Telemetrie und ESC_DATA habe ich noch nicht ausprobiert.
Meinst du, ich könnte dabei etwas beschädigen?
RV
12 October 2026 16:2512.10.2026 16:25
Quote: Honest answer:
I have no idea, I've never tested that.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Quote:Ehrliche Antwort:
Keine Ahnung, das habe ich nie getestet.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jurrien Saelens
16 October 2026 10:0716.10.2026 10:07
I just tested it and it works perfectly.
The rear end wasn't easy to adjust, but it works now.
Without a speed signal, the governor obviously doesn't work as well.
I then installed a Hyperion RDU phase speed sensor, and now everything works perfectly. The speed display on the transmitter works, and the governor is also regulating excellently.
Ich habe es gerade getestet und es funktioniert einwandfrei.
Das Heck war nicht einfach einzustellen, aber jetzt funktioniert es.
Ohne Drehzahlsignal funktioniert der Governor natürlich nicht so gut.
Ich habe dann einen Hyperion RDU Phasendrehzahlsensor eingebaut, und jetzt läuft alles super. Die Drehzahlanzeige im Sender funktioniert, und auch der Governor regelt jetzt hervorragend.
RV
16 October 2026 13:2016.10.2026 13:20
:-) :-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
:-) :-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Jurrien Saelens
24 October 2026 12:1824.10.2026 12:18
I really like the Goosky S2 Max with the VBar. I started with your Goosky preset, but after a few flights I ended up with almost the same settings as with the LOGO 200.
It flies really well. It's my favorite mini-helicopter now.
Edited once. Last edited on 24.10.2026 at 12:20 by Jurrien Saelens.
Mir gefällt der Goosky S2 Max mit der VBar wirklich sehr gut. Ich habe mit eurem Goosky-Preset angefangen, bin aber nach ein paar Flügen bei fast den gleichen Einstellungen wie beim LOGO 200 gelandet.
Er fliegt wirklich super. Mittlerweile mein Lieblings Miniheli.
1 mal bearbeitet. Zuletzt am 24.10.2026 12:20 von Jurrien Saelens.
RV
24 October 2026 18:3924.10.2026 18:39
:-)
Great, we're glad to hear that!
Thanks for testing it out!!!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
:-)
prima, das freut uns zu hören!
Danke fürs austesten!!!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.