Smartflyer
25 October 2026 22:1325.10.2026 22:13
Good evening,
I've connected the telemetry port and the single RPM cable to the EVO and I'm getting the RPM reading. Is there any way to determine if the signal is actually coming through the RPM input and not the telemetry input?
Nabend,
ich habe am EVO den Telemetrieanschluss und das eizelne RPM Kabel angeschlossen und bekomme auch die Drehzahl. Kann ich irgendwie feststellen ib das Signal auf wirklich üner den RPM Eingang und nicht über den TelemetrieEingang kommt ?
RV
25 October 2026 22:2125.10.2026 22:21
If you go to the model status and scroll down – the value shown there comes from the RPM sensor. You can also simply unplug the TELE cable; the value will remain the same.
Otherwise, there are 2 RPM values available for displaying/logging/outputting in the user screen/custom logs/custom announcements ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Wenn Du in den Modell Status gehst und runterscrollst - das was da steht kommt vom RPM Sensor. Man kann auch das TELE Kabel einfach dabei abziehen, der Wert bleibt.
Ansonsten gibt es für den Userscreen/Eigene Logs/Eigene Ansagen 2 RPM Angaben zum einblenden/loggen/ausgeben ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Smartflyer
25 October 2026 23:3925.10.2026 23:39
Okay, I've now adjusted the "screen" accordingly. I then disconnected the telemetry cable and am now seeing the RPM signal on both displays. (So it seems to be working correctly).
Can I still see somewhere in the logs where the signal is coming from (telemetry input or RPM input)?
(I have 2 other helicopters, but I can't just easily access the telemetry cable on those.)
So, ich hab mir jetzt den "Screen" entsprechend angepasst. Habe das Telemetriekabel dann abgezogen und bekomme auf beiden Anzeigen das Drehzahlsignal angezeigt. ( Scheint also richtig zu funktionieren).
Kann ich denn trotzdem irgendwo in den logs sehen wo das Signal herkommt ( Telemetrieeingang oder RPM Eingang)?
( Habe noch 2 andere Helis, aber da komm ich nicht mal so eben ans Telemetriekabel ran.
RV
26 October 2026 07:3626.10.2026 07:36
So:
In the standard log, this comes from the controller telemetry (T).
If this is not present, a fallback to the VBar RPM (V) input is active.
The same applies to the display above with (T). It also falls back to (V).
The one with (V) is always from the stabilizer.
So you don't necessarily have to unplug the cable - if the display at the top is sufficient for comparison.
If you have the Pro Value Pack, you can log both (T) and (V) in a separate graphical log. The same applies to the app for adding your own announcements.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Also:
Im Standard Log kommt das von der Reglertelemetrie (T).
Wenn diese nicht da ist ist ein Fallback auf VStabi RPM (V) Eingang aktiv.
Genauso ist es mit der Anzeige oben mit (T). Auch Fallback auf (V).
Die mit (V) ist immer vom Stabi.
Man muss das Kabel also gar nicht unbedingt abziehen - wenn einem die Anzeige oben reicht zum Vergleichen.
Wenn Du den Pro Value Pack hast kannst Du beide (T) und (V) in einem eigenen grafischen Log loggen. Genauso mit der App für eigene Ansagen dazu.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.