sme
18 September 2026 14:4118.09.2026 14:41
Hello,
Unfortunately, I had a problem with my TDR2 today.
It has a NEO module installed.
After takeoff, the helicopter tipped forward and to the right.
I managed to land the helicopter. However, it tipped over again while turning.
I couldn't see anything unusual in the log. The helicopter also initialized normally.
Can you possibly see anything else in the log? (SN 20003118).
Is there anything else I can check?
Best regards
Stefan
Hallo,
ich hatte heute leider ein Prblem mit meinem TDR2.
Es ist ein NEO verbaut.
Nach dem Abheben kippte der Heli nach vorne rechts weg.
Ich konnte den Heli noch landen. Er ist allerdings beim ausdrehen doch noch umgekippt.
Im log konnte ich ncihts auffälliges sehen. Der Heli hatte auch normal initialisiert.
Könnt ihr evtl. noch was anderes im Log erkennen? (SN 20003118).
Kann ich nochwas prüfen?
Viele Grüße
Stefan
RV
18 September 2026 15:0818.09.2026 15:08
Hmm... apart from a few vibration alerts, there's nothing. But... that could be a clue.
Run the helicopter without blades and check the vibrations in the VBC (Model Info). Please take a screenshot of that.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hmmm ... ausser ein paar Vibrationswarnungen ist da nix. Aber ... das könnte schon ein Hinweis sein.
Lass den Heli mal ohne Blätter laufen und schaue die Vibrationen in der VBC (Modell Info) an. Mach davon dann einen Screeenshot bitte.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
sme
19 September 2026 06:4319.09.2026 06:43
Hello Rainer,
I'll send you a screenshot once I've repaired the helicopter after my vacation.
Best regards
Stefan
Hallo Rainer,
ich melde mich mit dem Screenshot wenn ich den Heli nach meinem Urlaub repariert.
Viele Grüße
Stefan
sme
21 September 2026 19:4421.09.2026 19:44
Hello Rainer,
Luckily, only the linkage was defective.
Here is a screenshot of the test run without leaves.
It looks completely inconspicuous.
Any other ideas?
Best regards
Stefan
Hallo Rainer,
war zum Glück nur Gestänge defekt.
Hier der Screenshot vom Probelauf ihne Blätter.
Sieht total unauffällig aus.
Noch weitere Ideen?
Vilee Grüße
Stefan
RV
21 September 2026 19:5721.09.2026 19:57
Hmmm... really unspectacular.
Could you try testing it carefully with rear blades?
The best way to do this is to unhook the rear linkage; then they will automatically move into "zero lane".
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Hmmm ... wirklich unspektakulär.
Kannst Du mal vorsichtig mit Heckblättern testen?
Am Besten dazu das Heckgestänge aushängen, dann laufen die von selbst in "Nullspur".
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
22 September 2026 08:5622.09.2026 08:56
Hi Stefan,
But that's also a relatively old VBar (from 10-2015), it could be that it's simply past its prime.
From a support perspective, I don't have a maximum age or a certain number of flight hours before it's better to replace them; you simply never know what kind of stresses such a device has been exposed to over time.
Or... something went wrong during initialization, the helicopter moved, the stick moved.
Another indicator that can be helpful is the rescue status indicator, showing whether it behaves normally or whether the ball runs away unexpectedly or without motivation.
And then, during a test run or the next flight, please pay close attention to the swashplate and the rotor. Normally, you can see when the helicopter wants to pull away as it's starting up or being gently pressed down. If that happens, it's best to cut the motor, let it land on its skids, and usually nothing will happen.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Stefan,
das ist aber auch 'ne relativ alte VStabi (aus 10-2015), könnte auch sein, dass die's einfach hinter sich hat.
Ich hab aus Support-Sicht jetzt kein Höchstalter oder so-und-so-viele Flugstunden bis man sie besser austauschen sollte, man weiß einfach auch nie, welchen Belastungen so ein Gerät im Laufe der Zeit ausgesetzt war.
Oder ... bei der Initialisierung ist was schief gelaufen, Heli bewegt, Knüppel bewegt.
Was noch ein Indikator sein kann ist die Rettungs-Status-Anzeige, ob die sich normal verhält, oder ob der Ball unerwartet oder unmotiviert wegläuft.
Und dann halt bei einem Probelauf oder beim nächsten Flug bitte genau auf die Taumelscheibe, den Rotor achten, normal sieht man's schon gut beim Hochlaufen/leicht machen, das der Heli wegziehen möchte. Dann besser Motor aus, plumps auf die Kufen, i. d. R. nix passiert.
Grüßle
Eddi
Born to fly ...
forced to work.
sme
22 September 2026 16:2922.09.2026 16:29
Hello Rainer, Hello Eddi,
I can only do the next test run next week (vacation).
Unfortunately, the drifting only became apparent after takeoff.
I did manage to land it, but the counter-steering as the revs dropped just before the end wasn't enough to prevent it from tipping over. The TDR2 isn't exactly known for its stability.
Although the Neo is no longer young, it has seen relatively few deployments.
Of course it gets shaken - it's a TDR2 after all - the sensors have been known to get stuck before.
Perhaps there really was a problem during initialization?
I didn't want to exchange it for an Evo; I was told by a competition pilot that they have problems setting up the Evo properly for speed flying and therefore buy up leftover Neos.
Best regards
Stefan
Edited once. Last edited on 22.09.2026 at 16:31 by sme.
Hallo Rainer, Hallo Eddi,
den nächsten Testlauf kann ich erst nächste Woche machen (Urlaub).
Leider hat sich das wegdriften erst nach dem abheben gezeigt.
Gelandet habe ich ihn dann ja noch, nur hat das Gegensteuern bei abnehmender Drehzahl kurz vor Schluß nicht mehr gereicht um ihn am umkippen zu hindern. Der TDR2 steht halt auch nicht superstabil.
Die Neo ist zwar nicht mehr jung, hat aber recht wenig Einsätze hinter sich.
Geschüttelt wird sie natürlich schon - ist halt ein TDR2 - da blieben die Sensoren ja auch schonmal hängen.
Vielleicht hat es ja wirklich ein Problem beim initialisieren gegeben???
Austausch gegen eine Evo wollte ich nicht machen, ich habe mir von einem Wettbewerbsflieger sagen lassen, dass Sie beim Speedfliegen Probleme haben die Evo vernünftig einzustellen und daher Reste an Neos aufkaufen.
Viele Grüße
Stefan
1 mal bearbeitet. Zuletzt am 22.09.2026 16:31 von sme.
Eddi E. aus G.
25 September 2026 09:0625.09.2026 09:06
Hi,
The sensor issue with the NEO only concerns/concerned the accelerometers, which play no role in normal flight and are used at most for lightness (which only affects pitch). I think we can disregard them.
I can't contribute anything regarding EVO and Speed... but I don't know why not?
However, you'll have to invest some time and effort again; simply reusing old setups (or doing so without adjustments), which seems to be a national pastime these days, probably won't yield the best results. But in my opinion, the EVO isn't to blame for that ;-)
Grüßle
Eddi
Born to fly ...
forced to work.
Hoi,
das mit den Sensoren betrifft/betraf bei der NEO nur die Beschleunigungssensoren, die spielen beim normalen Fliegen keine Rolle, werden maximal für Leichtigkeit verwendet (die wirkt aber nur auf Pitch). Kann man denke ich ausklammern.
EVO und Speed kann ich nix beisteuern ... aber ich wüsste nicht, warum nicht?
Man wird allerdings wieder etwas Liebe investieren und probieren müssen, alte Setups übernehmen (oder ohne Anpassung), was ja gefühlt Volkssport ist, wird vermutlich nicht zum besten Ergebnis führen. Da kann mMn aber die EVO nix für ;-)
Grüßle
Eddi
Born to fly ...
forced to work.
sme
4 October 2026 18:2104.10.2026 18:21
Hello,
I finally had time to do the test run with tail rotor blades.
It looks unspectacular.
What else could I test?
Best regards
Stefan
Hallo,
ich hatte jetzt endlich Zeit den Testlauf mit Heckrotorblättern zu machen.
Sieht auch unspektakulär aus.
Was könnte ich noch testen?
Viele Grüße
Stefan
RV
4 October 2026 19:5204.10.2026 19:52
Okay - you really can't see anything.
Question: Is it possible that the switch in the rescue system (if present) is set to also operate in beginner mode?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Okay - da sieht man echt nichts.
FGrage: Ist in der rettung (Wenn vorhanden) möglicherweise der Schalter so eingestellt dass er auch Beginner Mode bedient?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
sme
4 October 2026 20:0104.10.2026 20:01
Hello Rainer,
The helicopter has a rescue system, but the beginner mode is not activated.
Was that perhaps simply an initialization error?
Of course, I want to be as certain as possible that this won't happen again on the next start.
Best regards
Stefan
Hallo Rainer,
der Heli hat zwar Rettung, aber der Beginner Modus ist nicht aktiviert.
War das vielleicht einfach nur ein Initalisierungsfehler?
Ich möchte natürlich schon möglichst sicher ausschließen, dass das beim nächsten Start wieder passiert.
Viele Grüße
Stefan
RV
4 October 2026 23:0504.10.2026 23:05
Well, the logged data doesn't say anything about that. Theoretically, it's conceivable if the helicopter was constantly moved in the same direction during the sensor calibration phase – but since that takes 1-2 seconds, it's rather unlikely.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Naja - die geloggten Daten sagen nix diesbezüglich. Theoretisch denkbar wenn der Heli während der Einmessphase der Sensorik konstant in dieselbe Richtung bewegt wurde - da das 1-2 Sekunden aber dauert - eher unwahrscheinlich.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
sme
5 October 2026 07:4605.10.2026 07:46
Hello Rainer,
It was windy that day. Could any movement caused by the wind have been enough to prevent proper initialization?
Do you have any other ideas what I can do?
Best regards
Stefan
Hallo Rainer,
an dem Tag war es windig. Kann da eventuelle Bewegung durch Wind gereicht haben um richtiges Initialisieren zu verhindern?
Hast du sonst noch Ideen was ich machen kann?
Viele Grüße
Stefan
Eddi E. aus G.
5 October 2026 10:1705.10.2026 10:17
Hi Stefan,
'Anything is possible' ... I can't recall that initialization in windy conditions was really a problem; in case of doubt, it takes a second or a few seconds longer.
I've certainly had cases in my career where the model wanted to go somewhere else during takeoff.
Engine off, head scratched, off-on, it works.
However, I have very rarely encountered helicopters that weren't stable :-)
Alternatively, if you have access to a different VBar, you can of course try that one as well.
And please also check the stick calibration in the transmitter, a) whether it is OK and b) whether it consistently achieves the same values when you move, center, and also the next time, e.g. the next day.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Stefan,
'möglich ist alles' ... ich kann mich jetzt nicht entsinne, dass Initialisieren bei Wind wirklich ein Problem war, im Zweifel dauert es 'ne Sekunde oder ein paar länger.
Ich hatte in meiner Karriere sicher auch schon Fälle, wo das Modell beim Abheben irgendwohin weg wollte.
Motor Aus, Kopf kratzen, aus-an, geht.
Allerdings hatte ich auch seltenst Helis, die nicht sicher stehen :-)
Ansonsten, falls Du Zugriff auf eine andere VStabi hast, kannst Du natürlich auch mal die probieren.
Und im Sender bitte auch mal in die Knüppel-Kalibrierung schauen, a) ob sie OK ist und b) ob sie stabil immer wieder die selben Werte erreicht, wenn man die Knüppel auslenkt, zentriert, und auch beim nächsten Mal, am nächsten Tag bspw.
Grüßle
Eddi
Born to fly ...
forced to work.
sme
11 October 2026 09:0911.10.2026 09:09
Hi Eddi,
Unfortunately, I don't have a spare stabilizer lying around to swap it out.
The joysticks work perfectly. Other helicopters also work without any problems.
Yes, unfortunately the TDR2 is not very stable.
Do you have any other ideas about what I can/should check?
Best regards
Stefan
Hallo Eddi,
leider habe ich keine Stabi in Reserve rumliegen um sie mal zu tauschen.
Die Knüppel funktionieren einwandfrei. Andere Helis machen auch keine Probleme.
Ja , leider steht der TDR2 nicht besonders stabil.
Habt ihr noch andere Ideen, was ich prüfen kann/sollte?
Viele Grüße
Stefan
cc1975
11 October 2026 09:1011.10.2026 09:10
Perhaps try changing the initialization from precise to normal; maybe that will help.
Regards, Christian
Eventuell die Initialisierung mal von präzise auf normal stellen, vielleicht hilft das ja was.
Gruß Christian
Eddi E. aus G.
12 October 2026 09:1512.10.2026 09:15
Hi Christian,
I don't think so, unless it's rescue-related (Beginner Mode, which Rainer already asked about), and even then... Precision standard for a NEO means that – if the z-axis sensor of the more precise 16G IMU 'sticks' (mechanically jams/sticks) after being switched off/on due to vibration in the previous flight – it can still be reliably initialized with the remaining 5 accelerometer elements: 2 x x-axis | 2 x y-axis | 1 x z-axis (from the 200G high-range sensor).
This does not affect the gyroscopic system (flight attitude stabilization).
And if it were rescue-related, the cause would most likely be unfavorable vibration/resonance during startup, so that the sensors are shaken – not stirred – 'wobbling' and do not form a reliable reference.
Grüßle
Eddi
Born to fly ...
forced to work.
Moin Christian,
glaube nicht, wenn's nicht rettungsbezogen (Beginner Mode, was Rainer ja schon fragte) ist, und selbst dann ... Präzision-Standard bedeutet ja bei einer NEO, dass – wenn der z-Achsen-Sensor der präziseren 16-G-IMU auf Grund von Vibration im vorherigen Flug nach Aus-/Einschalten 'hängt' (mechanisch klemmt/anhaftet) – mit den verbliebenen 5 Beschleunigungssensor-Elementen 2 x x-Achse | 2 x y-Achse | 1 x z-Achse (vom 200 G-High-Range-Sensor) trotzdem sicher initialisiert werden kann.
Die Gyros (Fluglage-Stabilisierung) trifft das nicht.
Und wenn's rettungsbezogen wäre, wäre die Ursache höchstwahrscheinlich schon ungünstige Vibration/Resonanz beim Hochlaufen, so dass die Sensoren geschüttelt–nicht gerührt 'rumeiern', keine verlässliche Referenz bilden.
Grüßle
Eddi
Born to fly ...
forced to work.
sme
1 November 2026 12:0301.11.2026 12:03
Hello Eddi, Hello Rainer,
I finally found the time yesterday to test the helicopter again.
The tipping over was probably just an initialization error.
The test flight went smoothly.
Is there anything else I can check before the start in the future?
Attached is a screenshot taken while hovering. The vibrations are very minimal.
Best regards
Stefan
Hallo Eddi, Hallo Rainer,
ich habe gestern endlich die Zeit gefundenden Heli wieder zu testen.
Das Umkippn war vermutlich wirklich nur ein Initialisierungsfehler.
Der Testflug verlief problemlos.
Kann ich da evtl. in der Zukunft noch vor dem Start irgendwas mehr kontrollieren?
Anbei ein Screenshot im Schwebeflug. Die Vibrationen sind sehr gering.
Viele Grüße
Stefan
Eddi E. aus G.
2 November 2026 09:4002.11.2026 09:40
Hi Stefan,
It looks inconspicuous :-) .
Otherwise, just the usual: when starting up, make sure that the swashplate remains horizontal, doesn't do anything uncontrolled/unexpected, and when making it light, also pay attention to whether the model wants to warp in any way.
In the air, be ready to switch to the 'safe bank' immediately, or to turn off the engine and auto-rotate or land the helicopter.
If it were indeed vibration, experience shows that the cause disappears immediately and the model behaves normally again.
Unless the stabilizer is actually faulty (sensors), but that wouldn't be a problem that only occurs randomly, but rather repeatable immediately, or as soon as the drive is running, or as soon as you reach a speed with a nasty vibration or resonance.
Grüßle
Eddi
Born to fly ...
forced to work.
Hi Stefan,
sieht unauffällig aus :-) .
Sonst, eigentlich nur das übliche: beim Anlaufen drauf achten, dass die Taumelscheibe waagrecht bleibt, nix ungesteuertes/unerwartetes macht, und beim Leicht machen halt auch drauf achten, ob das Modell irgendwie verziehen möchte.
In der Luft, bereit sein, beim Bank-Schalten bereit sein, sofort wieder in die 'sichere Bank' zu schalten, oder den Antrieb auszuschalten und den Heli auto-zu-rotieren oder abzusetzen.
Wenn's doch Vibration wäre, ist erfahrungsgemäß die Ursache sofort weg, das Modell verhält sich wieder normal.
Außer, die Stabi hätte wirklich einen weg (Sensorik), aber das wäre dann kein Problem, das nur zufällig auftritt, sondern eher wiederholbar sofort, oder sobald der Antrieb läuft, oder sobald man in eine Drehzahl mit einer fiesen Vibration oder Resonanz kommt.
Grüßle
Eddi
Born to fly ...
forced to work.