WFEGb
5 November 2026 17:0005.11.2026 17:00
Hello,
As already mentioned in the other thread, "Never change a running system..." would certainly have been better heeded, but...
During the modifications, I stopped using the blue sensor. Which parameters on the Neo should I adjust to "imitation" the flight behavior with the old sensor? (A brief initial test revealed an unpleasant, low-amplitude jittering around the head...)
Best regards
Werner
Hallo,
Wie schon im anderen Thread "Never change a running system..." wäre sicher beherzigt besser gewesen, aber...
Im Zuge der Umbauten habe ich auf die bisherige Nutzung des blauen Sensors verzichtet. An welchen Parametern der Neo sollte ich drehen, um das Flugverhalten mit altem Sensor zu "imitieren"? (Ein kurzer Erstversuch zeigte ein unschönes Zittern mit kleiner Amplitude um den Kopf herum...)
Beste Grüße
Werner
Fingolf
5 November 2026 17:5405.11.2026 17:54
How did you install the stabilizer bar, and what was its installation position?
Stephan
Wie hast du die Stabi verbaut, Einbauposition?
Stephan
WFEGb
6 November 2026 01:1906.11.2026 01:19
Hi Stephan,
The stabilizer bar retained its installation location (under the cabin floor – connections facing rearward, V-shaped downwards). The external sensor was glued to the fuel tank and closer to the rotor mast...
Best regards
Werner
Hallo Stephan,
die Stabi hat ihren Einbauort (unter dem Kabinenboden - Anschlüsse nach hinten, V nach unten) behalten. Der externe Sensor war auf den Tank geklebt und näher am Rotormast...
Beste Grüße
Werner
RV
6 November 2026 07:1006.11.2026 07:10
Proximity to the mast didn't matter.
The integrated sensor has a better resolution - and it would be responsible for rescue operations anyway.
When exactly and how strong does the effect occur, which helicopter is it exactly, what are the key specifications?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Die Nähe zum Mast ist egal gewesen.
Der integrierte Sensor löst besser auf - und für Rettung wäre er eh zuständig.
Wann genau und wie stark tritt der Effekt auf, welcher Heli ist es denn genau, wie sind die Eckdaten?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
WFEGb
6 November 2026 11:5506.11.2026 11:55
Hello Rainer,
It's the Vario PTH2-Lama (with Benda 3-blade propeller, Helitec blades, and SK 3-blade tail rotor). The effect occurs during hovering and small control inputs, and then takes ages to settle down. It's more of a tremor around the elevator than a wobble. When flying calmly (which is pretty much all I do with the model anyway...) I don't notice anything, but then the same thing happens again when braking into a hover. (Perhaps the sensitivity of the Neo's internal sensors just needs to be reduced?)
My question should be more along the lines of: Are there any fundamental changes that should be made to the setup when dispensing with the external sensor?
Best regards
Werner
PS: Right now, the temperature issue with the PHT2 is the main focus before the next flight tests...
Hallo Rainer,
es ist die Vario PTH2-Lama (mit Benda-3Blatt, Helitec-Blättern und SK-3-Blatt-Heckrotor. Der Effekt tritt beim Schweben und kleinen Steuerbewegungen auf und braucht dann eine "halbe Ewigkeit" um sich wieder zu beruhigen. Es ist mehr ein Zittern um den HR als ein Wobbeln. Beim ruhigen Herumfliegen (mehr mache ich mit dem Modell ohnehin nicht...) bemerke ich nichts, dann aber wieder Gleiches beim Abbremsen in den Schwebeflug. (Vielleicht muss die Empfindlichkeit für die innere Sensorik des Neo nur heruntergestellt werden?)
Meine Frage sollte mehr in die Richtung gehen: Gibt es beim Verzicht auf den externen Sensor grundsätzliche Änderungen, die im Setup vorgenommen werden sollten.
Beste Grüße
Werner
PS: Im Moment steht die Temperaturgeschichte mit der PHT2 im Vordergrund vor den nächsten Flugversuchen...
Eddi E. aus G.
6 November 2026 12:1006.11.2026 12:10
Hi Werner,
It's been too long... although we did allow the external sensor with the NEO, as a backup or because it can be placed somewhere else in the model than the VBar, or because some people still wanted the flight feel of a black or blue or Silverline, we ourselves always only used the internal sensors.
Normally, it is sufficient to specify both sensors correctly (installation position), and since the external one is then the primary one, you configure it accordingly.
Let's see your setup and give some more information about the model and equipment, weight, servos, power supply.
The installation position in the cabin sounds good at first, good damping of vibrations/resonances, but if the cabin could vibrate in any way, the VBar could also pick up and output something there that the old sensor didn't detect elsewhere.
Or the older sensor was simply too insensitive for that :-)
If in doubt, yes, first experiment with the sensitivity and compare. But as I said, with the setup (cloud and information about where/when is also OK!) you can better see the current status, and with a little more information... :-)
—Eddi
Born to fly ...
forced to work.
Moin Werner,
es ist zu lange her ... wir hatten zwar bei der NEO den externen Sensor weiterhin ermöglicht, als Backup oder weil man ihn halt woanders im Modell platzieren kann als die VStabi, oder weil manche das Fluggefühl von einem schwarzen oder blauen oder Silverline weiterhin haben wollten, haben aber selbst immer nur die internen Sensoren verwendet.
Normal reicht es, beide Sensoren halt richtig anzugeben (Einbaulage), und da der externe dann der primäre ist, stellt man eben auch dafür ein.
Lass doch mal Dein Setup sehen und gib noch ein paar mehr Infos zum Modell und der Ausrüstung, Gewicht, Servos, Spannungsversorgung.
Die Einbauposition in der Kabine klingt erst mal gut, gute Dämpfung von Vibrationen/Resonanzen, aber wenn die Kabine irgendwie schwingen könnte, könnte die VStabi dort auch was aufnehmen und ausgeben, was der alte Sensor woanders nicht erfasst hat.
Oder der ältere Sensor war einfach zu unempfindlich dafür :-)
Im Zweifel, ja, spiel zuerst mal mit der Empfindlichkeit, vergleiche. Aber wie gesagt, mit dem Setup (Cloud und Info wenn/wo ist auch OK!) kann man besser sehen, was der Ist-Stand ist, und mit ein paar Infos mehr ... :-)
—Eddi
Born to fly ...
forced to work.