Good morning,
I'm still stuck with my M4 Max and Vstabi Evo. The rear-end sway just won't stop.
I would rule out the tail mechanism, as I completely rebuilt it with new parts. The tail linkage is extremely smooth, with no play anywhere.
I haven't changed any of the transmitter settings yet (except for adjusting the tail sensitivity for testing purposes), so I wouldn't know which values to use. Perhaps you could lend me a hand? :-)
Set up:
OMPHobby M4 Max (Live Hobby PNP Version)
Rear servo: DS3515T
Controller: OMPhobby 85A
Main rotor blades: RT-420 Ultimate
Tail rotor blades: RT-72 Ultimate (RT-71 and kit blades also tested)
Vcontrol serial number: 11005776
Bank 1: 1920, Bank 2: approx. 2100, Bank 3: approx. 2300 (The higher the head speed, the more noticeable the oscillation.
Firmware everywhere (transmitter, VBar and controller) is up to date.
The rear sensitivity is set to 60; I tried it earlier at 70 and then at 50 for testing purposes. However, I couldn't detect any change.
Here is a link to the video of today's flight, where you can clearly see the commuting:
https://unim8trix.org/m4_max.mp4
Best regards,
Tobias
I'm still stuck with my M4 Max and Vstabi Evo. The rear-end sway just won't stop.
I would rule out the tail mechanism, as I completely rebuilt it with new parts. The tail linkage is extremely smooth, with no play anywhere.
I haven't changed any of the transmitter settings yet (except for adjusting the tail sensitivity for testing purposes), so I wouldn't know which values to use. Perhaps you could lend me a hand? :-)
Set up:
OMPHobby M4 Max (Live Hobby PNP Version)
Rear servo: DS3515T
Controller: OMPhobby 85A
Main rotor blades: RT-420 Ultimate
Tail rotor blades: RT-72 Ultimate (RT-71 and kit blades also tested)
Vcontrol serial number: 11005776
Bank 1: 1920, Bank 2: approx. 2100, Bank 3: approx. 2300 (The higher the head speed, the more noticeable the oscillation.
Firmware everywhere (transmitter, VBar and controller) is up to date.
The rear sensitivity is set to 60; I tried it earlier at 70 and then at 50 for testing purposes. However, I couldn't detect any change.
Here is a link to the video of today's flight, where you can clearly see the commuting:
https://unim8trix.org/m4_max.mp4
Best regards,
Tobias
Moin,
ich komme mit meinem M4 Max und Vstabi Evo nicht weiter. Das Heckpendeln will einfach nicht aufhören.
Ich würde die Heckmechanik ausschließen, da ich sie extra noch einmal kopmplett mit Neuteilen aufgebaut. Die Heckanlenkung ist super leichtgängig, nirgendwo spiel.
An den Werten im Sender habe ich noch nichts verstellt (bis auf Heckempfindlichkeit testweise), da wüsste ich auch nicht welche Werte da in Frage kommen. Vielleicht könnt ihr mir die Arme greifen :-)
Setup:
OMPHobby M4 Max (Live-Hobby PNP Version)
Heckservo: DS3515T
Regler: OMPHobby 85A
Hauptrotorblätter: RT-420 Ultimate
Heckrotorblätter: RT-72 Ultimate (Getestet auch RT-71 und Kit Blätter)
Vcontrol Seriennummer: 11005776
Bank1: 1920, Bank2: ca 2100, Bank3: ca. 2300 (Je höher die Kopfdrehzahl, desto auffäliger das Pendeln.
Firmware überall (Sender, VStabi und Regler) auf dem aktuellen Stand.
Die Heckempfindlichkeit steht auf 60, ich hatte vorhin testweise mal auf 70 und dann auf 50. Ich konnte aber keine Änderung feststellen.
Hier ist ein Link zu dem Video vom heutigen Flug, wo man Pendeln gut sieht:
https://unim8trix.org/m4_max.mp4
Viele Grüße,
Tobias
ich komme mit meinem M4 Max und Vstabi Evo nicht weiter. Das Heckpendeln will einfach nicht aufhören.
Ich würde die Heckmechanik ausschließen, da ich sie extra noch einmal kopmplett mit Neuteilen aufgebaut. Die Heckanlenkung ist super leichtgängig, nirgendwo spiel.
An den Werten im Sender habe ich noch nichts verstellt (bis auf Heckempfindlichkeit testweise), da wüsste ich auch nicht welche Werte da in Frage kommen. Vielleicht könnt ihr mir die Arme greifen :-)
Setup:
OMPHobby M4 Max (Live-Hobby PNP Version)
Heckservo: DS3515T
Regler: OMPHobby 85A
Hauptrotorblätter: RT-420 Ultimate
Heckrotorblätter: RT-72 Ultimate (Getestet auch RT-71 und Kit Blätter)
Vcontrol Seriennummer: 11005776
Bank1: 1920, Bank2: ca 2100, Bank3: ca. 2300 (Je höher die Kopfdrehzahl, desto auffäliger das Pendeln.
Firmware überall (Sender, VStabi und Regler) auf dem aktuellen Stand.
Die Heckempfindlichkeit steht auf 60, ich hatte vorhin testweise mal auf 70 und dann auf 50. Ich konnte aber keine Änderung feststellen.
Hier ist ein Link zu dem Video vom heutigen Flug, wo man Pendeln gut sieht:
https://unim8trix.org/m4_max.mp4
Viele Grüße,
Tobias
machine-translated from German · Show original