← VBar Control Classic

Classic VBC and Neo with satellite - UI sensor issue

VBar Control › VBar Control Classic · Started by nkma on 13 July 2026 18:2113.07.2026 18:21
nkma 13 July 2026 18:2113.07.2026 18:21
I have an original VBC.
I have a Logo 500 with a Neo with a # 04883 satellite.
I have a Hobbywing RPM sensor connected to two of the motor poles and to RPM port on Neo. It works as it should.
I also have a Mikado UI-sensor, # 04890 on the battery wires. I have not succeded to figure out how to connect the wires from the small signal port on the UI-sensor to the Neo, so that the Neo sees that I have a UI-sensor.

What is the correct way to connect the UI-sensor to the Neo so that my VBC gets the UI information?

I can make the cable, if I only know how it should be made and how it should be connected to the Neo.

/Bo
RV 13 July 2026 20:5013.07.2026 20:50
There is a "Spectrum Style" JST socket at the UI Sensor. This must be connected to one of both "Spektrum Style" JST Ports at the VBar NEO.

If you don't have a cable for it - you can use any cable for Spektrum Sats or order one at Mikado.

Don't forget to load the UI and Battery Logbook ap on the VBC of course.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 13.07.2026 20:51 von RV.
machine-translated from German · Show original
nkma 14 July 2026 09:1314.07.2026 09:13
I have the UI app installed and activated in the VBC.
I tried with the long black/grey/grey cable that came with a UI sensor.
I connected the cable from the UI sensor into one of the two JST sockets on the Neo.
I tried three different UI sensors. I tried both connectors on the Neo.
The UI sensor did not show up on the start screen on the VBC or under apps in the VBC.

What can be wrong?

/Bo
nkma 14 July 2026 09:3114.07.2026 09:31
Sorry about the colors of the cable. It is gray/black/black and nothing else.

/Bo
Eddi E. aus G. 14 July 2026 10:0214.07.2026 10:02
Hey Bo,

please check in Model Setup / Macrocell Setup / Configuration if the Digital Input is maybe still set to Spektrum protocol.

The TELE(metry) ports double as Spektrum Satellite ports when used with satellites, then without telemetry, and any receiver configuration always has priority (for safety reasons).

Please also double-check that you have the corresponding Apps installed and enabled, namely U/I Sensor, Battery Logbook (for telemetry) and NEO/EVO Macrocells (to be able to check and if necessary change the configuration).

—Eddi

Born to fly ...
forced to work.
nkma 14 July 2026 13:1014.07.2026 13:10
In Model Setup / Macrocell Setup / Configuration, Digital Input was set to "None (Aux1)".
I tried to change that to "UDI" and rebooted.
I still don't see the UI-sensor. Not on VBC start screen and not under apps.

/Bo
Eddi E. aus G. 14 July 2026 14:1114.07.2026 14:11
Hi,

None (Aux1) is OK. Was OK.

UDI means, universal digital interface, which is a standardized protocol from us, implemented by e.g. Jeti, Graupner, Multiplex, JR.
Now the VBar is (also) listening to such a receiver connected to AUX1 ;-) – better reverse that change.

Do you happen to have access to another VBar flybarless controller, where you could just connect the U/I sensor and check if it pops up then?
Or do you happen to have access to another VBar telemetry item, on another model maybe, which you could just connect to this VBar, see if it pops up there, too?

—Eddi

Born to fly ...
forced to work.
nkma 14 July 2026 14:2514.07.2026 14:25
I'm in the process of putting together a Logo 700, also with a Neo connected to the VBC.
With some luck it can be ready later this week. Then I can test another UI-sensor on the Logo 700. I may get the opportunity to test with a friend's VBC later this week.
I will get back when I have more results. Thank you for the help, so far!

/Bo
VStabi VStabi Pioneer of Flybarless