← VBar Control Classic

"Governor sensor no signal"

VBar Control › VBar Control Classic · Started by ReadyToFly on 7 April 2025 21:5707.04.2025 21:57
ReadyToFly 7 April 2025 21:5707.04.2025 21:57
Hello, guys,

The motor of my heli stopped working in flight. In event log, I found the "governor sensor no signal" entry at the very moment the problem happened in real life.

I found an old video from Mr. Mel telling that it may be caused by bad insulation. So, I revised the length of the motor screws and every wire on my heli, but didn't find anything wrong.

What else could cause this problem, please?

Thanks.


Edited 2 time(s). Last edit at 04/07/2025 10:24PM by ReadyToFly.
ReadyToFly 7 April 2025 21:5907.04.2025 21:59
The ESC is a Hobbywing 200A with a BEC and an RPM sensor.
RV 7 April 2025 22:2607.04.2025 22:26
Hello,

in which way does the problem occur in flight? Did you loose RPM or anything else?

Which helicopter and engine is it?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
ReadyToFly 7 April 2025 22:3607.04.2025 22:36
Hi,

The motor simply stops in flight suddenly. Not gradually, but in one go. No loss of rpm.

Also, it happens rarely. Two times in 20 flights or so.

It is an XlPower V1 with an HK-4530-450kv Scorpion motor.
Eddi E. aus G. 8 April 2025 09:3908.04.2025 09:39
Hi,

any special settings in the ESC (and the VBar), or default? Particularly frequency and timing?

This could be an electric fault (insulation, ground loop, sparking), or it could have another reason (e.g. 'sharp' settings), why the ESC is losing commutation—the few times I saw/heard that happen, the motor stopped even with a weird sound. And it was always with 'large cans', big motors, more likely 50xx size, but also 45xx.

One result is, apart from the obvious, that the ESC maybe and maybe only briefly does no longer output a valid rpm signal, or (earlier) that an external rpm sensor didn't.

Unfortunately, there seem to be no cloud entries for this. Correlating the event log with the current/voltage log (by timeline) could provide more insight.

If in doubt, I'd probably go and have the ESC and the motor checked, by their respective manufacturers.

Kind regards

Eddi

Born to fly ...
forced to work.
ReadyToFly 8 April 2025 19:2908.04.2025 19:29
Hi,
Do you think the problem would go away if I used the ESC governor instead of Mikado's?
Thanks.
RV 8 April 2025 20:1008.04.2025 20:10
Using the ESC internal gov - the RPM signal cable can be unplugged, the error messages would no longer come up.

Anyway - if there is an issue which is being shown with the RPM signal error like saturation, insulation etc. - this still persists and might result in a shut down motor mid air ....

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
machine-translated from German · Show original
VStabi VStabi Pioneer of Flybarless