← VBar NEO for external transmitters

Neo and Kontronik Jive pro and Ext Gov translated

VBar › VBar NEO for external transmitters · Started by HaEr on 30 August 2015 20:4130.08.2015 20:41
HaEr 30 August 2015 20:4130.08.2015 20:41
Hi Team,

This is my first Vbar ever. I have Neo + Rescue, the setup has been very easy.
I have one issue that I do not understand.

I am using JR XG8 and Xbus, all is working.
I am using all the features in Jive Pro (Bail out, slow start) I have also programed a delay in the radio. Also programed (Deactivate Bail out)
on the throttle cut switch.

I did this via Aux2 and assign Aux 2 to throttle channel, my case this is changel 5 when running Xbus Mode B.

The reason why I did this this way, was I do not have a throttle channel in my receiver, I need to go through Neo.

Now to my question, I do not understand how to use ESC channel in Neo.
So I do not know if I would prefer Neo or using Aux2 as I am doing now.

In Gov.1 I did chose external ESC gov and did Reset to external.
In Gov.2 I did not do anything I have already done this before, when running this radio.

Now in Meny,
what should Throttle out be in different banks, I do not understrand?
I am using delay in radion when shifting between flight modes.

Autorotation??
What value should be here?? In Kontornik pro for JR this is stated as 25.
But I do not understand what value to have here.

I tried reading the manual, but still not very clear.

Happy Neo owner, struggling a little.

//Hasse

RV 30 August 2015 20:5830.08.2015 20:58
- Connect the ESC to "ESC"
- dial in your % Value for your desired HS in the Throttle out (switch banks). E.g. 70,75 and 80%
- dial in 25% for AR

Check w/o blades on the bench

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
HaEr 30 August 2015 21:2530.08.2015 21:25
This means that I will not be able to change throttle value via radio, correct?
Will radio delay between Bank modes (Flight modes) still work, or will radios throttle be total by passed.

If I am using auto (Bank 3) and, land. because there has not gone 25 sec, I use throttle cut switch and switch to bank 2,
deactivating the 25 sec rule. And it do a slow start as usual. Will this work the same?

Thanks for the support.
HaEr 30 August 2015 21:5130.08.2015 21:51
One more question, Is it okay to use Aux2 and remap the channel as I am doing now?
RV 30 August 2015 22:2730.08.2015 22:27
Quote:This means that I will not be able to change throttle value via radio, correct?

With a 3rd Party TX yes - with a Vbar Control - not ;-)


Quote:If I am using auto (Bank 3) and, land. because there has not gone 25 sec, I use throttle cut switch and switch to bank 2,
deactivating the 25 sec rule. And it do a slow start as usual. Will this work the same?

Didn't test it - i don't fly Kontronik ;-( - Try on the bench w/o blades. We use a 3-way for motor - and toggle to "stop" on the ground everytime for soft spoolup.


Quote:Is it okay to use Aux2 and remap the channel as I am doing now?

We need the Motor status channel for correctly working control loops as requested - So you need a second "oldshool channel" for this - because the 2 signals (motor for NEO and RPM for this ESC) are different now!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
HaEr 31 August 2015 00:0431.08.2015 00:04
Thanks, one more question for clarify.

I have mapped Aux2 to throttle channel. And this seems to work fine "passing Neo Ext Gov Function"
If I am doing this, this is the same as using external throttle, for example esc into throttle channel of receiver.

If I am ok with this, does this mean I am messing up the control loop for NEO. Neo control loop prefer
to use the ESC channel?

If I am doing this via AUX2 what will I mess up, I am just trying to understan my options :-)

Thanks for great support.

Vbar control would love one, concept is great. Not in my budget at the moment :-)



1 mal bearbeitet. Zuletzt am 31.08.2015 00:09 von HaEr.
Eddi E. aus G. 31 August 2015 08:4631.08.2015 08:46
Hi again,

please map AUX3, not AUX2. This has to do with the option of connecting a VBar Control Satellite to AUX2 and 3 as an option, and although both works, AUX3 is better for the simple reason that the NEO is outputting a signal to detect a satellite on AUX2 at power up, which could initialize the ESC unintentionally.

Also keep fail safe in mind. On ESC, we can switch the ESC to the known motor off position because it's programmed in the VBar.
On AUX we do not know, so we do not output a control signal in fail safe. Most known ESCs cut throttle if signal is lost after a fraction of a second, so this is about the safest thing we can do without knowing what's behind AUX.

But if your radio (the receiver) does not communicate a proper fail safe state, but outputs e.g. hold or neutral to the servos and a certain throttle position, VBar would not know about the fail safe state (e.g. connection lost between radio and receiver), and just output what it gets as an input.

Means, check on the bench and set accordingly so the motor turns off a) if the radio is turned off and b) if the receiver is disconnected from the VBar.

You are not messing up _if_ you are giving the proper states of the ESC and Motor to the NEO, so use a mixer in your radio and check that the motor switch position changes properly with the ESC status (e.g. OFF, autorotation bailout/IDLE, ON).

Kind regards

Eddi

Born to fly ...
forced to work.
HaEr 31 August 2015 10:1731.08.2015 10:17
Thanks,
all question are clarified for now.

//Hasse
VStabi VStabi Pioneer of Flybarless