← VBar NEO for external transmitters

vbar neo - is governor mandatory? translated

VBar › VBar NEO for external transmitters · Started by ReadyToFly on 15 October 2015 21:1115.10.2015 21:11
ReadyToFly 15 October 2015 21:1115.10.2015 21:11
hi,
is the use of governor, be it neo's or an external one, mandatory with vbar neo?
what happens if i connect the ESC cable directly to my rx throttle channel? would i be able to run flat non-governed TC curves?
thanks.
RV 15 October 2015 22:5815.10.2015 22:58
You can run the neo in non-neo-gov mode. Either with fixed values for each bank - or - with values by TX.

For TX values - see point 4 here:

http://www.vstabi.info/en/neo_transmitter

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ReadyToFly 16 October 2015 12:3916.10.2015 12:39
hello RV,

If you want to dial in the headspeed (ext. Gov) from TX as known in the past - this can be done routing the needed signal to AUX3 (only this one!). Ensure that a additional signal to "Our" motor status channel is needed which represents off, run and - if used - autorotation.

I'd like to use my Castle Creation "governor high" option. With this option I don't have to set a target hs on the ESC, but I can have different flat tc on my radio, each one for a different hs (just like vbar silverline). Is it possible?

If so, how to set up Neo and my 8fg, please? You guys mentioned aux3 above, but wouldn't I have to have the throttle channel active on my radio to do that? Currently I've replaced the throttle channel on my radio for aux3 in order to use the Neo governor. So, I'm kind of lost here on how to do that.

Thanks.
RV 16 October 2015 19:1516.10.2015 19:15
Quote:With this option I don't have to set a target hs on the ESC, but I can have different flat tc on my radio, each one for a different hs (just like vbar silverline). Is it possible?

Yes - this is the AUX3 way ...


Quote:how to set up Neo and my 8fg, please?

Hmmm ... please understand ... i don't try it - my way is published. I recommend at least VBar Governor and Banks - and as best with a VBar Control.

If you like to have throttle curves (they will be the key for AUX3 ESC) - just try them as usual with unplugged motor on the bench, and set up the TX according to our requrements at the bars and switch displays in pc software.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless