Installing the NEO with Kosmik and using XBus mode B. The problem is that Xbus mode B does not support channels to be connected to the receiver and Kosmik does not support external governors. So where and how to set the throttle input so that the TCurves from the TX can be used to establish the Kosmik governor? Another problem is to have another channel for retracts, where will this plug into the Neo?
← VBar NEO for external transmitters
Neo with JR DMSS and Kosmik translated
VBar › VBar NEO for external transmitters ·
Started by Vinger on 19 October 2015 23:3619.10.2015 23:36
Vinger
19 October 2015 23:3619.10.2015 23:36
RV
20 October 2015 07:4120.10.2015 07:41
We use fixed values each bank - similar to a VBar Control. This can't be changed in your situation. Anyway - 3 Headspeeds should be enough.
For retracts - have a look at the AUX assignments in RX Tab ;-)
if there is no channel left (because you have assigned a rescue, a throttle cut for nitro etc.) - Time to get a Vbar Control and its Makrocells ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
For retracts - have a look at the AUX assignments in RX Tab ;-)
if there is no channel left (because you have assigned a rescue, a throttle cut for nitro etc.) - Time to get a Vbar Control and its Makrocells ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Vinger
20 October 2015 18:1920.10.2015 18:19
Now even more regretting buying the NEO, Mikado is trying to lock us diehard fans of the VBar out. Stating to get a VControl is not really an answer to a honest question. All indications was that the Neo will replace the VBar and now I am stuck with a product I cannot use unless I buy another product for $800????
Nowhere in the manual or other info on the Neo did it state that we will lose the ability to use TC from our radios or that I would need a VControl to use a non VLink Neo......
Nowhere in the manual or other info on the Neo did it state that we will lose the ability to use TC from our radios or that I would need a VControl to use a non VLink Neo......
ulrich
20 October 2015 18:3020.10.2015 18:30
Man, relax. Rainer just set a :-) in his text.
You are not locked out or something. Its just our idea how we can do things best like its done in the VBar Control. Other Radios dont have this capabilities, so you have to use other probably slightly more complicated solutions.
If you connect the Kosmik to your receiver, you have all normal control over it with your transmitter. There is no need to use the NEO for this, since if you use Kosmik as governor, NEO has absolut nothing to do with it.
However, if you just want to route your throttle channel through NEO, i.e. if your Rx does not have additional ports, there is a solution for this as well (Use AUX Channels). The governor in NEO is intended to be a governor, which in your case is not used.
so long ... Uli
http://www.vstabi.de
You are not locked out or something. Its just our idea how we can do things best like its done in the VBar Control. Other Radios dont have this capabilities, so you have to use other probably slightly more complicated solutions.
If you connect the Kosmik to your receiver, you have all normal control over it with your transmitter. There is no need to use the NEO for this, since if you use Kosmik as governor, NEO has absolut nothing to do with it.
However, if you just want to route your throttle channel through NEO, i.e. if your Rx does not have additional ports, there is a solution for this as well (Use AUX Channels). The governor in NEO is intended to be a governor, which in your case is not used.
so long ... Uli
http://www.vstabi.de
RV
20 October 2015 19:4420.10.2015 19:44
Quote:If you connect the Kosmik to your receiver, you have all normal control over it with your transmitter. There is no need to use the NEO for this, since if you use Kosmik as governor, NEO has absolut nothing to do with it.
Well - i have JR radio here and tried what Uli suggested - as it works in this way on Futaba, Jeti and Graupner systems.
Unfortunately JR disables all other outputs if a X.Bus is enabled ;-(
So - time to contact JR how to enable the slots - if you need them ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 20.10.2015 19:57 von RV.
Well - i have JR radio here and tried what Uli suggested - as it works in this way on Futaba, Jeti and Graupner systems.
Unfortunately JR disables all other outputs if a X.Bus is enabled ;-(
So - time to contact JR how to enable the slots - if you need them ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 20.10.2015 19:57 von RV.
RV
20 October 2015 19:5720.10.2015 19:57
Here we go ... JR XG14 fully set up as in my example - and additional AUX2 (JR AUX5) and AUX 3 (JR AUX7) for free use ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ulrich
20 October 2015 22:0520.10.2015 22:05
I just talked to Rainer and am very surprised to hear, that JR is deactivating all PPM outputs on the receiver, if X-Bus is selected. Can anybody explain why JR is doing this? I mean it cuts lots of possibilities of the radio if using with X-Bus. I dont understand this.
All other Manufacturers (Futaba, Jeti, Hott) are not doing this, enabling people to fully use their radios in parallel with the single line usage.
so long ... Uli
http://www.vstabi.de
All other Manufacturers (Futaba, Jeti, Hott) are not doing this, enabling people to fully use their radios in parallel with the single line usage.
so long ... Uli
http://www.vstabi.de
Vinger
21 October 2015 08:2121.10.2015 08:21
The PPM ports on the RX are only inactive when selecting MODE B, with MODE A they all work, but unfortunately VBar does not support MODE A. So is this JR's fault or Mikados fault?
Thanks RV will try your solition with throttle via AUX2 and hopefully the other AUX3 for retracts. Did you mix throttle to the AUX channel or did you use DEVICE SELECT to change the throttle channel?
This will be for my new TDR2....
1 mal bearbeitet. Zuletzt am 21.10.2015 08:23 von Vinger.
Thanks RV will try your solition with throttle via AUX2 and hopefully the other AUX3 for retracts. Did you mix throttle to the AUX channel or did you use DEVICE SELECT to change the throttle channel?
This will be for my new TDR2....
1 mal bearbeitet. Zuletzt am 21.10.2015 08:23 von Vinger.
Eddi E. aus G.
21 October 2015 08:5121.10.2015 08:51
Hi,
throttle in this case should be AUX 3, not AUX 2. The reason is that AUX 2 and AUX 3 can also be used for a VBar Control Satellite receiver, and on initial power up, VBar NEO checks for the presence of such a satellite (once) by emitting 'one ping' one AUX 2. _And_ motor fail safe is done on AUX 3 by means of no longer outputting a signal in case of fail safe, which causes almost all known ESCs to cut throttle within a fraction of a second.
The 'ping' on AUX 2 _could_ cause an ESC to unintentionally initialize, and if the switch positions are not in motor off position, the ESC might unintentionally spool up. Usually, an ESC should not react to such data bursts or discard them as garbage, but depending on the ESC's programming ... better safe'n sorry.
Kind regards
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 21.10.2015 08:51 von Eddi E. aus G..
throttle in this case should be AUX 3, not AUX 2. The reason is that AUX 2 and AUX 3 can also be used for a VBar Control Satellite receiver, and on initial power up, VBar NEO checks for the presence of such a satellite (once) by emitting 'one ping' one AUX 2. _And_ motor fail safe is done on AUX 3 by means of no longer outputting a signal in case of fail safe, which causes almost all known ESCs to cut throttle within a fraction of a second.
The 'ping' on AUX 2 _could_ cause an ESC to unintentionally initialize, and if the switch positions are not in motor off position, the ESC might unintentionally spool up. Usually, an ESC should not react to such data bursts or discard them as garbage, but depending on the ESC's programming ... better safe'n sorry.
Kind regards
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 21.10.2015 08:51 von Eddi E. aus G..
RV
21 October 2015 13:0321.10.2015 13:03
I don't mix anything - as my setup is according to a VBC.
Anyway - if you assign the throttle channel to AUX3 - and assign another channel which represents the motor switch status to "Motor" - it should work.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Anyway - if you assign the throttle channel to AUX3 - and assign another channel which represents the motor switch status to "Motor" - it should work.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
21 October 2015 13:0421.10.2015 13:04
Quote:This will be for my new TDR2....
OK ...
http://vstabi.info/en/node/2048
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
OK ...
http://vstabi.info/en/node/2048
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Vinger
21 October 2015 14:5021.10.2015 14:50
OK Aux3 for throttle then and I plug the master cable from the Kosmik into Aux3, this should then eliminate the motor start/stop as well, as the ESC is now not going through the VBar electronics? So normality to control the ESC is resumed and all done from the TX without interference from VBar settings.
Eddi E. aus G.
21 October 2015 15:0921.10.2015 15:09
Hi,
exactly, the throttle channel this way is routed through the VBar and output without interference to AUX3.
Just mind the settings for the actual motor switch you see above in Rainer's screenshot: the VBar should know if the motor is running or not, because of a) features in the control loop that require that information and b) for logging the proper motor states (which helps in analyzing the log, should it become necessary).
Kind regards
Eddi
Born to fly ...
forced to work.
exactly, the throttle channel this way is routed through the VBar and output without interference to AUX3.
Just mind the settings for the actual motor switch you see above in Rainer's screenshot: the VBar should know if the motor is running or not, because of a) features in the control loop that require that information and b) for logging the proper motor states (which helps in analyzing the log, should it become necessary).
Kind regards
Eddi
Born to fly ...
forced to work.
Vinger
21 October 2015 19:1621.10.2015 19:16
Thanks will use the motor start stop then mixed to my HOLD switch. Anything I have to set in the governor page except to set it to external?
RV
21 October 2015 22:3421.10.2015 22:34
No - nothing needed in this case.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.