← VBar NEO for external transmitters

Neo nitro gov throttle trim? translated

VBar › VBar NEO for external transmitters · Started by Vinger on 11 December 2015 03:5711.12.2015 03:57
Vinger 11 December 2015 03:5711.12.2015 03:57
Setup is Futaba 14SG, SBus, Neo and fitted on a Gaui NX7. Followed the setup from http://vstabi.info/en/node/2030 and all works correctly.

What we cannot get to work is the throttle trim and the old method of lifting the lower endpoint to get trim active does not work. How do I get the throttle trim to work iot set idle speed?

VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
RV 11 December 2015 08:1311.12.2015 08:13
All throttle related values are stored in the NEO. They are parameters - and don't be touched with "Channels" from your radio.

- lower (off) position
- full position
- idle
- bailout idle
- throttle curve / other parameters

So - you don't have access with a "oldschool" radio as it doesn't have the capability to change these values over the air like a VBar Control.

You might to set up everything with a laptop on the field - and choose a throttle value for idle which works at different conditions too.

And - to run the heli with a 3rd party radio - it is essentilally needed to map all switches (motor, banks, throttle cut) as required.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Vinger 11 December 2015 10:1011.12.2015 10:10
Thanks, figured out that all settings is in Neo.. Can one do the settings with a VLink attached with VControl and then bind back to SBus for normal flying by the owner of the heli?

VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
Eddi E. aus G. 11 December 2015 10:3911.12.2015 10:39
Hi,

of course. If both radios are on at the same time, you can even do cross-over buddy boxing with the VBar Control as the master, and help setting up the heli with the owner instantly able to try out the changes.

No need to change the receiver settings in the NEO software, if a VLink receiver is present it will be used, too, and as the primary receiver.

Kind regards

Eddi

Born to fly ...
forced to work.
Vinger 11 December 2015 11:0511.12.2015 11:05
That is very handy, thank Eddi.

VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
Ktmheli 17 December 2015 16:5217.12.2015 16:52
During different condition ie weather the motor can sometime need more throttle to idle.

The only way i found is on the PC. IS there no other way when using futaba to adjust idle on a trim?
RV 17 December 2015 19:2317.12.2015 19:23
Nope - as the idle is a VBar parameter it can be set up only with the pc - or as best - with a VBar Control.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
kswill 19 December 2015 20:0019.12.2015 20:00
Vinger schrieb:
-------------------------------------------------------
> Thanks, figured out that all settings is in Neo..
> Can one do the settings with a VLink attached with
> VControl and then bind back to SBus for normal
> flying by the owner of the heli?



Here is what it looks like in buddy box

https://vimeo.com/149512994

-dont mind the puddle of fuel ... haha



1 mal bearbeitet. Zuletzt am 19.12.2015 20:01 von kswill.
VStabi VStabi Pioneer of Flybarless