kswill
13 December 2015 01:4913.12.2015 01:49
Hello,
I am setting up my TSA 700N. I would like to inhibit the "Idle" part of the "Run-Idle-Stop" switch.
(my fingers need the space)
In playing with options, I have found that by bumping the "sub trim" of the switch controlling "Run-Idle-Stop" all the way up, I am able to see the "blue" part of the bar (in the "transmitter" tab page on the software) appear from the Idle mid point. This at the same time is taking away the yellow from the "Stop".
When the subtrim gets maxed out, the "Idle" becomes part of the "Run".
Testing on the bench, all systems seem to work as they should.
Bottom 2 positions are "Run" and all the way up position is "Stop"
Is this OK to use the sub trim to inhibit the "Idle" ?
Thank you
Kenny
RV
13 December 2015 11:1413.12.2015 11:14
Yep - it is ok.
Whatever you have to do on the TX - it doesn't care the Vbar. Only the result in the PC Software counts ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
kswill
13 December 2015 15:5713.12.2015 15:57
kswill
18 December 2015 16:3518.12.2015 16:35
ok, Im back....
I had thought I would be able to adjust "Stop" like I was able to adjust "hold" in my Futaba.
- I usually run a little higher motor rpm in my "hold" when using silverline vbar.
That wont happen here. I guess I need to use "Idle". So I am going to bump my sub-trims
the other way , this eliminating "Stop".
I have read some scary threads about spool up out of "Idle". What is the setting in the gov that adjusts the speed at which the motor spools after "Idle" ?
Thank you
1 mal bearbeitet. Zuletzt am 18.12.2015 16:38 von kswill.
RV
18 December 2015 19:1218.12.2015 19:12
Yep - in your case you need Idle ;-)
The Procedure as example:
- Turn model on in STOP (mandatory! - If you turn on in Idle or Run - Stop MUST be toggled once to enable the ESC output for safety)
- switch to run (normal spoolup - a switch to idle will not have any effect for the first start)
- fly
- toggle idle for auto
- if auto goes wrong - toggle run again - fasssst spoolup!
- fly
- toggle idle for auto
- auto is ok, toggle stop on the ground before run again (otherwise ... fasssst spoolup)
This is why we recommend a 3-way switch. it is very intuitive and simple with a 3-way!
Of course you can do it with 2 switches and mixers in your TX - but how ... and how complicated!
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
kswill
19 December 2015 02:5619.12.2015 02:56
Is there any way to adjust the motor rpm in "idle" ?
When switching between "Run" "Idle" "Stop", there is no change in motor rpm.
I would normally have a touch higher rpm in my "hold" on silverline.
Since "idle" is my 'hold", I wanted to up the rpm when I switch to "idle".
Is this possible. I am able to use Vcontrol to make changes if needed.
Thank you
1 mal bearbeitet. Zuletzt am 19.12.2015 02:57 von kswill.
RV
19 December 2015 11:1019.12.2015 11:10
Quote:Is there any way to adjust the motor rpm in "idle" ?
There is a AR Idle %-value on the pc soft main screen (Expert) with VGov.
With ext. Gov - the AR Idle field is below the Flight Values ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
kswill
19 December 2015 16:1019.12.2015 16:10
Yes, My NEO is loaded with pro and rescue.
I have played with the value in that setting. (AR)
I bumped it to 50 and did not experience any change.
[[[Could I possibly have an issue with my magnets?
Magnets are placed in clutch bell.
-- I have not flown the model yet. Still doing bench testing with no blades.
I have started motor and spooled up, but have not switched into bank 2 or 3.]]] - on second thought, this doesnt make sense.
2 mal bearbeitet. Zuletzt am 19.12.2015 19:07 von kswill.
RV
19 December 2015 20:4719.12.2015 20:47
Did you first toggle tu "run" before Idle (no one would fly AR off from the ground ...)?
It is working here - and adjustable.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
kswill
20 December 2015 01:4120.12.2015 01:41
Ahhhhh......
I see..... :-) :-)
I must be IN bank 2 or 3 for this to work.
Is there a way to have this active ( adjusting AR value) in all banks 1,2, and 3 ?
-thank you for your patience :-)
2 mal bearbeitet. Zuletzt am 20.12.2015 02:19 von kswill.
RV
20 December 2015 17:3420.12.2015 17:34
Quote:Is there a way to have this active ( adjusting AR value) in all banks 1,2, and 3
Hmm - it should work in bank 1 too.
Is there another thing assigned to the same switch as banks are assigned?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.