alexn
1 September 2015 23:2201.09.2015 23:22
Hello Mikado Team!
Probably due to the large number of questions I can get ban :-) , but I can't activate autotrim :-)
My TX - Futaba 14SG. Connection between NEO and RX - S.BUS
After power up NEO with full positive collective on my TX I don't get double collective twitch confirm, only one. Checkbox Act is checked. I don't understand what I'm doing wrong.
Screenshots my TX and NEO settings in attachment.
Best regards, Alexey
alexn
1 September 2015 23:3401.09.2015 23:34
Eddi E. aus G.
2 September 2015 08:4002.09.2015 08:40
Hi Alex,
please check your fail safe settings. Maybe the receiver is outputting center until it has a hand shake with the radio, which could be too late for the VBar to recognize full collective.
For 22 posts in 17 days, you won't get banned ... yet :-)
Cheers
Eddi
Born to fly ...
forced to work.
alexn
2 September 2015 20:1802.09.2015 20:18
Hello Eddi,
I check my failsafe settings, failsafe is disabled (see attachment please) :-(
Best regards, Alexey
RV
2 September 2015 20:3602.09.2015 20:36
A quick test:
Will you get the double twitch at full neg. collective?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alexn
2 September 2015 21:0002.09.2015 21:00
Eddi, I understand you think. No, single twitch.
Alexey
RV
2 September 2015 21:2202.09.2015 21:22
Well - ok - Maybe you have a pitch curve in this flight condition or a "general pitch trim" (had this on a T8)?
Can you please doe this steps:
- connect to pc
- TX on, full coll.
- pc soft start - toggle to TX calib. tab
- Model on
- read the % for collective after init
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alexn
2 September 2015 21:4902.09.2015 21:49
Hello Rainer,
I made screenshots in this sequence. Please see attacment in the first and second posts. I can make a video as a proof of my words.
14SG not have "general pitch trim" or I dont know about them. But, I disabled all trims and mix. And I deliberately made a screenshot "Servo monitor"
Best regards, Alexey
5 mal bearbeitet. Zuletzt am 02.09.2015 22:28 von alexn.
RV
3 September 2015 08:3003.09.2015 08:30
OK - just for a check:
Can you extend your TX throw for pos. collective a bit? -Lets say to 110% and retry?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alexn
3 September 2015 08:4803.09.2015 08:48
Hello Rainer,
I check it. I thought about it, and tried to increase the endpoint from -101 to +101 (etc -/+102,-/+103,-/+110,-/+120). NEO displays in the soft 102,103,104,111,121, but I don't get double collective twitch confirm.
I will try to replace the evening R7003SB RX (with installed resistor on S.BUS) on R7008SB and and re-check all.
2 mal bearbeitet. Zuletzt am 03.09.2015 09:06 von alexn.
RV
3 September 2015 17:3503.09.2015 17:35
Thnaks - please retry with the other rx.
If it won't work - safe the setup, zip and attach here ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alexn
3 September 2015 20:1503.09.2015 20:15
Hi Rainer,
I tested with R7008SB, tested with 110% on R7008SB - single twitch :-(
Any idea?
Video will be later.
Nonetheless, neo great flies :-)
Alexey
1 mal bearbeitet. Zuletzt am 03.09.2015 21:07 von alexn.
Dateianhänge:
öffnen |
Download -
alexn.zip
(476 bytes)
RV
3 September 2015 23:5403.09.2015 23:54
Got it - strange ;-(
Please increase the pos. collective from your 58 up to 63...65 for the Trim flight ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alexn
4 September 2015 08:1604.09.2015 08:16
Video (R7008SB, 100%) -
http://youtu.be/a_ufxil8bew
Video (R7008SB, 110%) -
http://youtu.be/SK2Eo8yu0Mk
Ok Rainer, I try it in the evening, but I do not like this idea.
Strange thing is that Autotrim on Silverline with this setup - no problem!
Alexey
2 mal bearbeitet. Zuletzt am 04.09.2015 08:30 von alexn.
Eddi E. aus G.
4 September 2015 08:5204.09.2015 08:52
Hi Alexey,
I remember we had a similar issue on 5.3, too: there, when collective was set up way out of the recommended range of values, auto trim would have activated but it would not have trimmed, because the range of values to detect hovering collective was exceeded.
Don't recall if it also affected enabling of auto trim.
Kind regards
Eddi
Born to fly ...
forced to work.
alexn
4 September 2015 09:3004.09.2015 09:30
Hi Eddi,
> Don't recall if it also affected enabling of auto trim.
On 5.3 don't affected enabling of auto trim.
On my Silverline was set 58 pos. collective. Autotrim? - no problem! Need to make a screenshot or video? I can show you the result of trimming!
Unfortunately this is a peculiarity mechanics Trex600 Nitro. I set the minimum possible servo arm size. The manufacturer recommends a larger size.
My actions?
Regards,
Alexey
5 mal bearbeitet. Zuletzt am 04.09.2015 10:02 von alexn.
Eddi E. aus G.
4 September 2015 09:4704.09.2015 09:47
Hi Alexey,
OK, there seems to be a difference. then. No need to make a video.
Until we have looked into this, you would have to follow Rainer's suggestion temporarily (you can re-set the value after the trim flight is done, of course).
Kind regards
Eddi
Born to fly ...
forced to work.
alexn
4 September 2015 10:1604.09.2015 10:16
Ok, Eddi.
I try Rainer's suggestion in the evening and report on the results.
Thanks!
Alexey
alexn
4 September 2015 17:2804.09.2015 17:28
That's funny!
Max. pos. collective less or equal 62 - single twitch.
Max. pos. collective more or equal 63 - double twitch.
Ooh! :-)
Do I understand correctly that can expect a new version of the firmware?
Alexey
RV
4 September 2015 21:3004.09.2015 21:30
We will see in future - it is on the list to be checked ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 04.09.2015 21:31 von RV.
LaBra
20 December 2015 11:0120.12.2015 11:01
Hallo,
muss das Thema nochmal aufmachen.
Habe selbes Problem. Komme nicht in den Autotrimmmodus.
Pitchweg ist auf 100%. Auch bis 125% probiert (Jeti per UDI).
VBar Control sagt FW aktuell, Vstabi PC Software ist 6.1.7 vom 21.8. Vstabi hat 6.1.33.
Failsafe aus auch schon probiert, dito mit direkter Signalausgabe.
Gibts ne Lösung?
Lars
cu,
Lars
Dateianhänge:
öffnen |
Download -
JR NEX6.vbr
(2.3 KB)
RV
20 December 2015 17:3520.12.2015 17:35
Hallo Lars,
bitte nich.vbr nennen - das geht damit nicht. Einfach gezipt anhängen wäre besser ;-)
Frage: Wieviel Punkte Pitch hast Du in der Stabi eingestellt?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
LaBra
28 December 2015 17:0728.12.2015 17:07
Hallo Rainer,
hier mein Setup.
Pitch ist knapp unterhalb des Einstellbalkens. Wert müsste im Setup drin sein. Bei drei Blättern bracuhts halt wenig...
Grüße,
Lars
Dateianhänge:
öffnen |
Download -
Nex6_1.zip
(540 bytes)
RV
28 December 2015 17:5928.12.2015 17:59
Genau daran liegts vermutlich, Lars.
Teste mal auf der Werkbank ab welchem Pitchwert er denn Doppelzuckt (ich glaube 70 oder so zu wissen).
Sag Bescheid, dann geb ichs an Uli weiter ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
LaBra
29 December 2015 21:5629.12.2015 21:56
Hi Rainer,
eingestellt habe ich 57. Der Doppelzuck kommt ab 63.
Wäre cool wenn man das fixen könnte. Ich hab inzwischen drei Heli's mit drei Blättern...
cu,
Lars