← VBar NEO for external transmitters

NEO Nitro gov bank 2 / bank 3 sputter translated

VBar › VBar NEO for external transmitters · Started by kswill on 27 December 2015 16:2827.12.2015 16:28
kswill 27 December 2015 16:2827.12.2015 16:28
TSA 700N
NEO with rescue - non vlink
YS91sr
Futaba GV-1 sensor
Futaba 14sg (using a Vcontrol for field adjustments - eventually for buddy box)
6303 (futaba) rx and Vcontrol rx.





I am having an issue that goes like this...



I lift off in Bank 1 (stick works for throttle).
I switch to Bank 2 and it sputters. The same with Bank 3.

In the Vcontrol I can see the sensor giving a value of 2208 when magnet passes. (using finger to move clutch bell).

I have copied all banks and then re-assigned new head speeds for each bank.
Bank 1 1260
Bank 2 1400
Bank 3 1500

These are just testing HS. Normally would be running 1500/1750/1950 HS.


- I also have the issue in the thread "NEO - Futaba 14sg - Run- Idle - Stop"
Where I am unable to adjust the "Idle" rpm in Bank 1. Wondering if these issues are connected somehow.

Thank you



2 mal bearbeitet. Zuletzt am 27.12.2015 18:11 von kswill.
RV 27 December 2015 19:0427.12.2015 19:04
Quote:In the Vcontrol I can see the sensor giving a value of 2208 when magnet passes. (using finger to move clutch bell).

There is a gov status panel - please do a screenshot while having this issue, post here. Post also the event log.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
kswill 27 December 2015 22:5227.12.2015 22:52
File type would not attach ".log"






VBar Start -- NEO HELI -- 27.12.2015 -- 12:04:46
12:04:46;1;Reset Reason: Power On
12:04:46;2;Governor in Motortune Mode
12:04:50;2;Calibration Finished
12:05:38;1;Motorswitch Motor On
12:05:42;1;Motorswitch Motor Off
12:05:43;2;Bank 2 Loaded
12:05:43;2;Governor Stop
12:05:44;2;Governor Active
12:05:44;1;Motorswitch Motor On
12:05:45;2;Bank 3 Loaded
12:05:52;2;Bank 2 Loaded
12:05:54;2;Bank 1 Loaded
12:05:54;2;Governor in Motortune Mode
12:05:57;2;Bank 2 Loaded
12:05:58;2;Governor Active
12:06:00;2;Bank 3 Loaded
12:06:08;2;Bank 1 Loaded
12:06:08;2;Governor in Motortune Mode
12:07:59;2;Bailout Start
12:08:00;2;Bailout End
12:08:04;1;Motorswitch Idle Bailout
12:08:04;1;Motorswitch Motor Off
12:08:05;1;Motorswitch Motor On
12:12:20;3;High Vibration Level
12:12:30;4;Extreme Vibration Level
12:12:31;2;Bank 2 Loaded
12:12:32;2;Governor Active
12:12:32;2;Governor is at Low Throttle Limit
12:12:32;2;Governor is at Low Throttle Limit
12:12:32;2;Governor is at Low Throttle Limit
12:12:33;2;Governor is at Low Throttle Limit
12:12:33;2;Governor is at Low Throttle Limit
12:12:33;2;Bank 1 Loaded
12:12:33;2;Governor in Motortune Mode
12:12:34;2;Governor is at Low Throttle Limit
12:12:35;2;Bank 2 Loaded
12:12:35;2;Governor Active
12:12:36;2;Governor is at Low Throttle Limit
12:12:36;2;Governor is at Low Throttle Limit
12:12:36;2;Governor is at Low Throttle Limit
12:12:36;2;Governor is at Low Throttle Limit
12:12:36;2;Governor is at Low Throttle Limit
12:12:36;2;Governor is at Low Throttle Limit
12:12:37;2;Governor is at Low Throttle Limit
12:12:37;2;Bank 1 Loaded
12:12:37;2;Governor in Motortune Mode
12:12:37;2;Governor is at Low Throttle Limit
12:12:40;4;Extreme Vibration Level
12:12:41;2;Bank 2 Loaded
12:12:41;2;Governor Active
12:12:41;2;Governor is at Low Throttle Limit
12:12:42;2;Bank 3 Loaded
12:12:42;2;Governor is at Low Throttle Limit
12:12:42;2;Governor is at Low Throttle Limit
12:12:42;2;Governor is at Low Throttle Limit
12:12:43;2;Governor is at Low Throttle Limit
12:12:43;2;Bank 2 Loaded
12:12:44;2;Bank 1 Loaded
12:12:45;2;Governor in Motortune Mode
12:12:50;4;Extreme Vibration Level
12:13:00;1;Motorswitch Idle Bailout
12:13:01;2;Raised Vibration Level
12:13:10;1;Motorswitch Motor On
12:13:11;4;Extreme Vibration Level
12:13:21;2;Raised Vibration Level
12:14:09;1;Motorswitch Idle Bailout
12:14:10;2;Bank 2 Loaded
12:14:13;2;Bank 1 Loaded
12:14:13;1;Motorswitch Motor On
12:14:17;2;Bank 2 Loaded
12:14:17;2;Governor Active
12:14:21;2;Bank 1 Loaded
12:14:21;2;Governor in Motortune Mode
12:14:22;3;High Vibration Level
12:14:28;1;Motorswitch Motor Off
12:14:29;1;Motorswitch Motor On
12:14:32;2;Raised Vibration Level
12:14:33;2;Bank 2 Loaded
12:14:34;2;Governor Active
12:14:42;4;Extreme Vibration Level
12:14:42;2;Governor is at Low Throttle Limit
12:14:43;2;Governor is at Low Throttle Limit
12:14:46;2;Bank 1 Loaded
12:14:47;2;Governor in Motortune Mode
12:14:49;2;Bank 2 Loaded
12:14:49;2;Governor Active
12:14:52;2;Governor Idle
12:14:52;1;Motorswitch Idle Bailout
12:14:52;4;Extreme Vibration Level
12:15:02;3;High Vibration Level
12:15:05;2;Bank 3 Loaded
12:15:06;2;Bank 2 Loaded
12:15:22;2;Governor Stop
12:15:22;1;Motorswitch Motor Off
12:15:23;1;Motorswitch Idle Bailout
12:15:24;2;Governor Active
12:15:24;1;Motorswitch Motor On
12:15:25;2;Bank 1 Loaded
12:15:25;2;Governor in Motortune Mode
12:15:29;1;Motorswitch Motor Off
12:15:30;1;Motorswitch Motor On
12:15:43;3;High Vibration Level
12:15:53;1;Motorswitch Motor Off
12:15:53;2;Raised Vibration Level
12:15:53;1;Motorswitch Motor On
12:16:03;3;High Vibration Level
12:16:13;4;Extreme Vibration Level
12:16:15;1;Motorswitch Idle Bailout
12:16:17;1;Motorswitch Motor Off
12:16:23;3;High Vibration Level
12:16:33;2;Raised Vibration Level
12:16:44;2;Raised Vibration Level
VBar Logfile End -- 27.12.2015 -- 12:17:15
kswill 27 December 2015 23:0927.12.2015 23:09
Here are some screen shots

kswill 27 December 2015 23:1027.12.2015 23:10
and some more.


I hope all this helps. I am very new to the Vcontrol.

RV 28 December 2015 16:5628.12.2015 16:56
Yep -- exactly what i have expected!

A lot of them in the log: Governor is at Low Throttle Limit

Have a look at the "Low" (almost on) - your throttle is below the min limit value - so the gov won't engage.

Read more about this here: http://www.vstabi.info/en/node/2030

Solution: Use a useful HS for this combo (think about the torque curve of a nitro ...) or use a smaller pinion.
OR - as workaround (but keep in mind - this low throttle values are hints for overgeared systems) - lower the min limit value.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 28.12.2015 16:58 von RV.
kswill 2 January 2016 05:4202.01.2016 05:42
I used 1700/1800/1900 HS and the Gov engaged. :-)

I now have another issue. Dont know if this is actually another thread.

But,

When doing upright pitch pumps. On descent ( neg. pitch) the gov. wants to overspeed. As well as sputter at the bottom of the pitch pump.
In version 5.3 pro Gov (expert hat), there is a parameter named " % Minimum Gov " I have used this to adjust the sputter at the bottom of the pitch pump.







What would be the " % Minimum Gov" parameter in the NEO ?
And what would I be adjusting for the overspeed on descent (neg pitch) ?




Thank you

RV 2 January 2016 12:3502.01.2016 12:35
It is the minimum throttle on a nitro as well. So - you can turn it down carefully a few points (5 or so)

But - if the motor may sputter - could it be a bit too rich mixture?

In general - on a nitro - we may have to accept a bit overspeeding in this situation which helps for the next pitch input. Otherwise the motor may get into trouble - they don't have as much torque as a electric.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless