racer-g
7 January 2016 06:3307.01.2016 06:33
Hi.I have Vbar Neo with Devo 10 running alternative firmware supporting spectrum sats and DSM2 sats installed on heli(Trex 550).I use this TX more than 1.5 years on other helis with no problems.
I have assigned ch5 on some switch and channel has 0 and +100.That switch i'm going to replace with reset switch so when it is off the channel has 0 and when it is activated it has +100.
My question is this enough to use rescue?I don't plan to use "beginner" .
Thanks in advance.
RV
7 January 2016 08:4907.01.2016 08:49
Just have a look in the PC Soft.
The rescue channel must show center (!) when untouched - and the end throws (side depending on mode) when used. It is also written in words there at the channel assignment tab - so you can check while playing around there ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
racer-g
7 January 2016 09:5207.01.2016 09:52
I just don't have rescue yet.Wanted to upgrade but wondering if it will work with my Devo10 so i don't need anothet TX :-) .I have read about requirements for rescue channel during setup and i think it's going to work.I just need little modification on switch.Thanks anyways.
I have another question if you don't mind.I have already flown 20 packs with my Trex550.My tail limits are 98-104 and i have 2degree torque comp.Is it normal for tail limits or they should be exactly equal?Tail holds perfect but i have small throw back at stop after clockwise pirouette.Tail gain is 80,headspeed 2100,gear ratio to tail 4.5,tail blades 90mm,belt driven..Is it because of limits or i need Pro to adjust it or go throw optimization?
2 mal bearbeitet. Zuletzt am 07.01.2016 09:57 von racer-g.
RV
7 January 2016 09:5707.01.2016 09:57
OK - for the tail .. the throw (blade angles) can be tried of course - but to estimate have a look at my Logo example here:
http://www.vstabi.info/en/node/842#tail
Also - most Trex have a lower tail gear ratio then Mikados - does it have the 4.2 or has it a 4.5 ratio?
Before we get into some pro settings - we should check both first ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
racer-g
7 January 2016 10:0107.01.2016 10:01
I was thinking about gear ratio too but counted myself and it is 4.5.Headspeed 2100(i know Align likes more) tail blades 90mm.Servo horn 90degree.
RV
7 January 2016 10:1107.01.2016 10:11
OK - can you post images of the tail rotor in its end positions like on my linked page ?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
racer-g
7 January 2016 10:4307.01.2016 10:43
I had to modify tail hub to have more throw on that side because i lost tail on hard tail in funnel.Now on that funnel tail holding well.
RV
7 January 2016 12:0507.01.2016 12:05
This looks well.
Where it comes from ... we have one side which makes a stop with and one againt the torque. A stop with the torque is almost easier than against ,-)
Using pro it can be a way to do a tail optimization flight and increase the stop gain. In some cases lowering the tail acceleration will equalize the stops - but makes them a bit softer.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
racer-g
7 January 2016 12:1807.01.2016 12:18
Thanks Rainer.Will upgrade Neo and give it a try.Have a nice day.