← VBar NEO for external transmitters

Last log of this heli translated

VBar › VBar NEO for external transmitters · Started by alatuf on 1 January 2016 05:0701.01.2016 05:07
Wolfram 8 January 2016 00:0408.01.2016 00:04
Hello alatuf,

glad to hear I could help you.

In addition: when you tighten a nut clockwise with a screwdriver, then the nut "works" against your arm and tries to turn your arm counterclockwise.

The nut doesn´t turn your arm clockwise and helps you to tighten herself.

Could you follow me?

For the rest of your problem: follow Rainers suggestion!

Gruß, Wolfram
alatuf 8 January 2016 03:3508.01.2016 03:35
Wolfam I completly followed you and now I understand! Rainer, I also followed your tail setup and I was a few linkage turns of it! But when I leave setup my tail always go to "that place" of the photo. I think it is not a problem because when you hold your heli to put it on the ground tail gyro will change tail position. What would be great is a way to center tail servo before take off or you always have to ajust tail with stick input to avoid a sudden yaw of the heli! Later I will fly and will tell the results. Lets see
RV 8 January 2016 11:2808.01.2016 11:28
Quote:But when I leave setup my tail always go to "that place" of the photo

Well - and then - as usual - the Trim flight does it into the right position ;-)

So - do a trim flight and then have a look again ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alatuf 8 January 2016 22:0008.01.2016 22:00
Rainer, thanks for all your patience! Today I went flying and my tail got better! Here is my numbers:

HS: 2300
Gyro gain: 70
Aceleration: 45
P gain: 80
I gain: 60
D gain: 0
Expo: 55
DMA Collective: 22
DMA Cyclic: 8
28 tail optimizer 30
Rudder auto trim: 10

I did a trim flight but my tail position never moves from that photo position no matter what I have done! But anyway I think this is not a problem! Or am I wrong!?

When flying I notice some tail behavior that I would like to get rid of:

I have a slow and small tail wag (on bank 1 I put HS 2280 and gyro gain at 60 and the wag were just a little lower). The wag sometimes can be seen on FFF and bank turns, but it is much more seeing on hover.

When I make a rudder input and then goes the stick to the center the tail stops and back a few times. The stop is not accurate.

When a crosswind gets tail it goes against the wind (yaw) in small steps

Sorry for my poor english! I don´t know the correct or usual names for tail behavior! But I hope with this description you can help me even more!!!

I also attached the log from my last flights and I am having some "raised vibration level" on begining or ending of flight! Should I be concerned about this? Have a look please!



1 mal bearbeitet. Zuletzt am 08.01.2016 22:15 von alatuf. Dateianhänge:
öffnen | Download - log-20003853-Jan-8--2016-6-45-38-PM.zip (1.8 KB)
VStabi VStabi Pioneer of Flybarless