← VBar NEO for external transmitters

Neo rescue translated

VBar › VBar NEO for external transmitters · Started by jimwardle on 14 January 2016 03:2614.01.2016 03:26
jimwardle 14 January 2016 03:2614.01.2016 03:26
Hi, I have two Neo's setup identical, one in my Goblin 570 and the other in my Goblin 700. I have set them to rescue only and using my Futaba 18SZ setting the switch to Aux 2. Flying and operating the rescue function on my 700 it works perfectly flipping upright and climbing safely. Flying and operating the rescue function on my 570 it will flip to upright ok but will descend instead of climb.I have adjusted from the default climb figure of 68 all the way up to 200 with no difference it will still descend.It appears to work correctly if I lay the model on it's side and operate the rescue function the swash will correct and when I return it to level it shows a positive pitch to climb,but when flying it always descends after leveling.I have calibrated it numerous times but with no change.Any idea's why it should do this ? :-/
Cheers
Jim

Eddi E. aus G. 14 January 2016 09:0614.01.2016 09:06
Hi Jim,

can you please attach both setup files here so we can compare?

Where and how are the VBars mounted on both helis (up front/back or down front/back)?

Kind regards

Eddi

Born to fly ...
forced to work.
jimwardle 15 January 2016 01:3415.01.2016 01:34
Hi, are these the setup you want to check. The Neo's are both positioned the same behind the mainshaft with the wiring facing forward.
Cheers
Jim

jimwardle 15 January 2016 01:4415.01.2016 01:44
Hi, here is a photo of the Neo mounted on my Goblin570 which descends instead of climbing when rescue function is applied.
Cheers
Jim

Eddi E. aus G. 15 January 2016 08:5415.01.2016 08:54
Hi Jim,

with setup file, I mean click Save in the PC software with the VBar connected, so all parameters will be saved into a single file, then attach that file here so I can load it myself and check.
With the screenshots, I always only see a small snippet of your settings and can not put them into relation to other parameters ;-)

Thanks, cheers

Eddi

Born to fly ...
forced to work.
jimwardle 15 January 2016 13:3415.01.2016 13:34
Hi Eddi, I have saved the file but it defaults to a DAT file which I cant attach.If I change the file type to one that is allowed are you able to change it back at your end ?. Ok I compressed it to a zip file, I hope that will be ok.
Jim Dateianhänge:
öffnen | Download - Goblin 570.zip (445 bytes)
jimwardle 17 January 2016 06:2117.01.2016 06:21
Hi Eddi, just got back home after flying my Goblin570 and it now climbs after actuating the rescue. During the week I went over the setup several times, but tried something different.I leveled the heli and with the rescue set at 65 I moved the pitch/throttle stick to mid position and pressed the calibration.It appeared no different than before i.e. if I laid it on its side and flicked the switch the swash acted to level and gave a positive pitch to the blades same as before so I expected no change when I flew it today.I flipped it inverted and and hit the rescue and it righted itself and climbed slowly.I have changed the climb figure to 100 but it still appears to climb slowly.Can you tell me how sensitive the adjustment is as I would have thought changing from 65 to 100 would have been very noticeable.I am happy now that it climbs rather than descends bit I want it to climb quicker.
Cheers
Jim Dateianhänge:
öffnen | Download - Goblin 570.zip (445 bytes)
Eddi E. aus G. 18 January 2016 10:0418.01.2016 10:04
Hi Jim,

sorry for the late reply. I just tried to decompress the .zip-files, but I can neither do it with a Mac or with Win10.

You can rename the original files .vbr to attach them here.

Kind regards

Eddi

Born to fly ...
forced to work.
jimwardle 18 January 2016 10:4318.01.2016 10:43
Ok try again. Dateianhänge:
öffnen | Download - Goblin 570.vbr (2.3 KB)
Eddi E. aus G. 18 January 2016 11:4518.01.2016 11:45
Hi,

I can not find anything unusual. Which head speeds do your throttle settings give?
At which head speed did you notice the slow climb?
At the 30 % setting, I would expect that, at 70 and 100 % the heli should climb considerably, but it also depends on the overall pitch angle at the blades.
Mind that the setting is bank sensitive, so you can enter higher values at lower head speeds and vice versa. The heli should not shoot in the air, just flip over and climb gently. You should see a noticeable difference between 65 and 100, sure.

When you hit 'calibrate' the collective position is not relevant, only that the VBar is leveled with regard to the ground, or in the unusual case when the VBar's Z axis is not parallel to the main shaft, the main shaft should be vertical (mind that this is not OK, since the control axis then are tilted with regard to the heli's axis). I'm just writing this because a few customers reported that to me, seems that some chassis designs are a little bit ... odd.

Now if it made a change after calibration, I would assume that the VBar was calibrated face-down in the past, which would mean it doesn't properly know it's position 'in space' :-)

Cheers

Eddi

Born to fly ...
forced to work.
jimwardle 19 January 2016 15:1119.01.2016 15:11
Hi Eddi, thank you for the prompt reply.I use the banks for the throttle 30 70 100 and I only use bank three 100% which is set for 2200rpm.I found on one of the forums that as Futaba defaults to - 100% to + 100% a recommendation is to change the end points to 0% to + 100% as per attached pics.I use aux 2 on the tx which when the switch is activated shows off to active on the software screen.If you look at the earlier pics of the screen dumps it shows active to invalid when the switch is activated.When the weather improves I will test it,but I feel confident that it is the transmitter settings I had wrong.
Do you agree ?
Cheers
Jim

Eddi E. aus G. 20 January 2016 08:3920.01.2016 08:39
Hi Jim,

with the end points, you refer to the channel you use for Rescue?

Rescue is a three position feature, means we usually have Rescue-Off-Beginner (invalid if the Rescue mode is set to Rescue only in Setup/Swash/Expert, means that in this position nothing useful (but also nothing unuseful/dangerous) will happen.

If you use a two position switch, it is mandatory to limit to 100 %/0% so you have Rescue Off as a switch position, to re-arm Rescue for the next occasion.
This is also why we recommend a spring loaded switch for Rescue, or a push button.
If you use a three position switch, you would have to actively set the switch back to center (Rescue Off/re-arm) if the Rescue position is not spring loaded.

Now a guess would be that you were not switching to Rescue on the 570 in the first place, but to Beginner: this would also flip the heli upright but not input collective, in Beginner mode the tilt angle of the model is limited, skids down, but you have full control over tail and collective. In Rescue, collective is added to push the heli upwards.

But now the settings have been changed, it's hard to prove of course :-) next time you experience an odd reaction, please save the current setup file and log file so we can try and analyze better, from the settings and the event log entries of the flight(s) where it happened. I would guess that the log file has been overwritten sufficiently now so we can no longer see what happened at the first time.

Kind regards

Eddi

Born to fly ...
forced to work.



1 mal bearbeitet. Zuletzt am 20.01.2016 08:39 von Eddi E. aus G..
jimwardle 24 January 2016 11:5724.01.2016 11:57
Hi Eddi, flew both my Goblin 700 and 570 using the settings as described in the previous message i.e. 0% to 100% on Chanel 7 aux 2 using the designated two position spring return switch for rescue and all is perfect now.The rescue works every time I flick the switch compared to before where I sometimes had to operate the switch a couple of times before it would operate.Flips upright and climbs slightly.I am very happy now !!!.
Thanks for your help.
Jim
Eddi E. aus G. 25 January 2016 10:3425.01.2016 10:34
:-) :-)

Born to fly ...
forced to work.
VStabi VStabi Pioneer of Flybarless