← VBar NEO for external transmitters

Graupner MZ-24 & Vbar Neo -- Wiring and Setup Questions translated

VBar › VBar NEO for external transmitters · Started by rasheem on 23 February 2016 11:5523.02.2016 11:55
rasheem 23 February 2016 11:5523.02.2016 11:55
Hello,

One of my friend wants to buy Vbar Neo. He uses Graupner MZ-24 transmitter, and probably has GR-12L and GR-24L receivers.

Since i'm a Vbar Neo and Vbar Control user, i know some information about Vbar Neo, but clearly no info about wiring and setup with Graupner MZ-24.


1) I've seen that Vstabi Neo software has HOTT channel arrangement in UDI RX (receiver tab). But, how do we connect receiver with Vbar neo?

Graupner has only receivers, not satellites. Do we use a single line connection between neo and receiver? Which ports should be connected?


2) Could you give some setup advices especially about channel operations in transmitter? How to configure throttle hold (motor switch), bankswitch, rescue and beginner mode switch?


Thanks and best regards,

Rasim.
RV 23 February 2016 19:0323.02.2016 19:03
1 - yes, select UDI in Vbar PC Soft - and read the instructions there. A Patch Cable is needed, will be connected into AUX1.

2 - i don't have a Graupner TX - but just set it up as needed for giving us the required inputs in the right directions. It can't be that difficult because we don't need any heli mixers.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
rasheem 24 February 2016 22:5624.02.2016 22:56
Danke Reiner ;-)

I guess we should set up the GR-24L receiver with SUMD output. And connect channel 8 (sumd output) on the receiver and aux1 on Neo with a patch cable. (patch cable comes with neo right?)

Then assign switches for motor, bankswitch and rescue(momentary) and check directions of bars. I hope we could set it up easily.

Grüße

Rasim.
RV 25 February 2016 05:4125.02.2016 05:41
Yes - this is the right track.

If i can get a hand on such a TX these days (not sure, depending on weather, long story) i'll try and take some photos too.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless