My new Neo will not connect to the software. I have registered it and downloaded the key but it still will not connect. What am I doing wrong?
← VBar NEO for external transmitters
New neo translated
VBar › VBar NEO for external transmitters ·
Started by ian Spencer on 17 March 2016 22:4417.03.2016 22:44
ian Spencer
17 March 2016 22:4417.03.2016 22:44
ian Spencer
17 March 2016 23:1017.03.2016 23:10
Just to confirm, I have 2 pc's one on windows 10 and the other on Windows 7 neither will connect
Eddi E. aus G.
18 March 2016 08:3918.03.2016 08:39
Hi Ian,
please make sure you do not have the boot plug on when trying to connect to the PC Software (it's only meant to put the VBar into update mode for use with the VBar Control Synchronizer/Manager).
Then, once connected and powered up, check the device manager: the VBar should show, but possibly as an unknown device if the automatic driver installation failed for some reason.
Now you can install the driver manually (point the wizard to c:\program files (x86)\VBarControl\drivers) and check the box so sub folders are included, confirm, and it should install and work/connect.
Kind regards
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 18.03.2016 08:39 von Eddi E. aus G..
please make sure you do not have the boot plug on when trying to connect to the PC Software (it's only meant to put the VBar into update mode for use with the VBar Control Synchronizer/Manager).
Then, once connected and powered up, check the device manager: the VBar should show, but possibly as an unknown device if the automatic driver installation failed for some reason.
Now you can install the driver manually (point the wizard to c:\program files (x86)\VBarControl\drivers) and check the box so sub folders are included, confirm, and it should install and work/connect.
Kind regards
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 18.03.2016 08:39 von Eddi E. aus G..
ian Spencer
18 March 2016 08:5218.03.2016 08:52
Thanks Eddi,
I had it packed up ready to return thinking it was one of the faulty batch but I can,t see the yellow sticker so maybe its not.
I will try it again tonight after work.
Kind regards,
Ian
I had it packed up ready to return thinking it was one of the faulty batch but I can,t see the yellow sticker so maybe its not.
I will try it again tonight after work.
Kind regards,
Ian
Eddi E. aus G.
18 March 2016 09:0218.03.2016 09:02
Hi Ian,
we have almost all of the actually few devices with yellow stickers back and replaced, so it's rather unlikely that you have one, and especially not if it's only been bought recently.
Edit: I have checked the one VBar NEO which is registered to your MikadoID, and it's not among the suspect devices, so don't worry.
Kind regards
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 18.03.2016 09:04 von Eddi E. aus G..
we have almost all of the actually few devices with yellow stickers back and replaced, so it's rather unlikely that you have one, and especially not if it's only been bought recently.
Edit: I have checked the one VBar NEO which is registered to your MikadoID, and it's not among the suspect devices, so don't worry.
Kind regards
Eddi
Born to fly ...
forced to work.
1 mal bearbeitet. Zuletzt am 18.03.2016 09:04 von Eddi E. aus G..
ian Spencer
18 March 2016 09:1418.03.2016 09:14
Thanks Eddi,
Should get it going tonight then.
With not having this problem connecting to my V5 I thought this would just connect.
Kind regards,
Ian
Should get it going tonight then.
With not having this problem connecting to my V5 I thought this would just connect.
Kind regards,
Ian
Eddi E. aus G.
18 March 2016 09:2518.03.2016 09:25
Hi Ian,
could be that the V5 has a different USB ID than the NEO, depending on when it was manufactured. So the NEO might require the driver to be installed again, for the other USB ID.
Best,
Eddi
Born to fly ...
forced to work.
could be that the V5 has a different USB ID than the NEO, depending on when it was manufactured. So the NEO might require the driver to be installed again, for the other USB ID.
Best,
Eddi
Born to fly ...
forced to work.
ian Spencer
18 March 2016 19:1918.03.2016 19:19
Thanks Eddi,
So simple when you know how. connected fine now on both PC's
Best regards,
Ian
1 mal bearbeitet. Zuletzt am 18.03.2016 19:20 von ian Spencer.
So simple when you know how. connected fine now on both PC's
Best regards,
Ian
1 mal bearbeitet. Zuletzt am 18.03.2016 19:20 von ian Spencer.
ian Spencer
20 March 2016 19:4220.03.2016 19:42
New Neo fitted to my 600SE - Awesome.
My old V Bar must have a tired sensor because the Neo holds the tail much better.
All same settings but it now just feels nailed in every axis. Thumbs off hover and no trim flight needed
Great job guys.
Now I would like to upgrade to pro and rescue.
For a fairly inexperienced flyer like me, what is a good way to test rescue without putting the Heli at risk?
I feel uncomfortable flying high enough to not worry about what happens.
My old V Bar must have a tired sensor because the Neo holds the tail much better.
All same settings but it now just feels nailed in every axis. Thumbs off hover and no trim flight needed
Great job guys.
Now I would like to upgrade to pro and rescue.
For a fairly inexperienced flyer like me, what is a good way to test rescue without putting the Heli at risk?
I feel uncomfortable flying high enough to not worry about what happens.
RV
20 March 2016 22:5020.03.2016 22:50
Well - i would check it on the bench first (some kind of getting used to trigger the rescue) w/o motor - also do some collective movement after the rescue (simulate a partial flight) to delete the collective ad.
As next - go into a hover (keep safety distance) and test. If it climbs too much, lower the rescue collective a bit (depending on RPM). There is nothing unexpected what will happen.
The try out of a turn (i use the downwards part ;-) ) or something else known to get used with it.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
As next - go into a hover (keep safety distance) and test. If it climbs too much, lower the rescue collective a bit (depending on RPM). There is nothing unexpected what will happen.
The try out of a turn (i use the downwards part ;-) ) or something else known to get used with it.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ian Spencer
21 March 2016 08:5521.03.2016 08:55
Thanks Rainer,
Something for the Easter holiday if the weather is good.
Regards,
Ian
Something for the Easter holiday if the weather is good.
Regards,
Ian