← VBar NEO for external transmitters

Aileron sensor value out of range translated

VBar › VBar NEO for external transmitters · Started by racer-g on 4 April 2016 14:5704.04.2016 14:57
racer-g 4 April 2016 14:5704.04.2016 14:57
Hi again.
My setup is Trex 550E,KST bls servos and Vbar Neo rescue.Headspeed 2250.Collective 12 and cyclic 11 degree.Cyclic ring 92.Rescue pitch 72
Two times i had this message in log after activating rescue "aileron sensor value out of range".
First time i was thinking it's because of high cyclic ring and i lowered it from 95 to 92 but after 20 flights and few activations of rescue i have it again.Rescue was activated from inverted hover or from flips or rolls,just was demonstrating how it works on public.
I didn't noticed any strange or suspicious movements from heli,just that messages in logs but i am worrying.
Is it bad sensor or mechanical problem?
Thanks in advance.
Here is part of log.
1:53 Motor Switch operated to ON
Info 1:59 Raised Vibration Level
Warn 2:08 High Vibration Level
Info 2:13 Rescue has been activated
Critical 2:14 Aileron Sensor Value out of Range
Info 2:15 Rescue has been completed
Warn 2:15 Rescue has been oversteered by the Pilot
Warn 2:17 High Vibration Level
Info 2:21 Rescue has been activated
Info 2:23 Rescue has been completed
Warn 2:23 Rescue has been oversteered by the Pilot
Info 2:26 Raised Vibration Level
OK 2:36 Good Health Message (10sec)
Info 2:45 Raised Vibration Level
Warn 2:54 High Vibration Level
Info 3:03 Raised Vibration Level
Info 3:12 Raised Vibration Level
Info 3:14 Rescue has been activated
Critical 3:15 Aileron Sensor Value out of Range
Info 3:16 Rescue has been completed
Warn 3:16 Rescue has been oversteered by the Pilot
Info 3:18 Rescue has been activated
Info 3:20 Rescue has been completed
Warn 3:20 Rescue has been oversteered by the Pilot
Info 3:21 Rescue has been activated
Warn 3:22 High Vibration Level
Info 3:23 Rescue has been completed
RV 4 April 2016 16:5904.04.2016 16:59
Well - it seem to be that the heli turned into normal position very quick. So - if it turned quick, just ahint that the sensor couldn't follow the rate.

Quote:cyclic 11 degree

At the 8deg setup menue?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
racer-g 4 April 2016 17:2804.04.2016 17:28
Yes.The heli flips and rolls very quick and i like it.Agility 115.
Yes.11 degree at 8 degree menu.
RV 4 April 2016 21:0604.04.2016 21:06
Quote:Yes.11 degree at 8 degree menu.

You might run the control loop out of its limits. So at the end - you will get into non-controlled rates.

Plese set up with 8 degree, set rate to 115 and then - adjust the optimizers first ;-)

http://www.vstabi.info/en/node/399

After this is done (for each bank) - and if it won't be fast enough - set the rates to higher values, can be set up to 240, test on one bank. Optis must be set too - but can be estimated in the same ratio than for 115 (usuallay starts with half rate values) ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
racer-g 5 April 2016 15:0805.04.2016 15:08
Ok.Thanks.
Have to readjust cyclic and run optimizations.So hard without Vcontrol :-)
VStabi VStabi Pioneer of Flybarless