Vinger
4 April 2016 21:3704.04.2016 21:37
Helping a friend do the setup of this combo, normal setup and it works as advertised. Now with the update to enable TX adjustment of tail gain we are trying to set that up. No matter what we do tail gain channel (Aux2) does not respond when when checking channels in the software, tried from channel 5 all the way to channel 9.
Are there any step by step setup guide for SBus an Neo to enable tail gain from TX, especially channel setup and if AVCS or NORMAL should be used in TX gyro menu? what to adjust, endpoints or Gyro menu values in the TX?
VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
RV
5 April 2016 05:5205.04.2016 05:52
If there is no reaction - can you please check the NEO firmware, maybe it isn't updated?
To be sure - select a channel to AUX2 which is known as working first (e.g. collective), set the check there too.
About AVCS etc. - this sucks always as all guys out there don't know their radio and the history of this s**t ;-( :
Futaba had only one channel for gyro gain in the past. Developing the GY401 (long ago ...) they looked for a possibility to switch between normal and HH mode in flight. So they decided to split the channel here. From 0 down to -100 is normal mode, from 0 up to 100 is HH mode. (if someone had delay on this channel - and going throuh center while changing modes - it was very funny ;-) so they made them also w/o delay when switching flight conditions in the TX ). So with the different modes you will get only difgferent value ranges to access. I would use a mode which gives either full or at least the upper half of throw.
At least - the VBar does never care about any names in a TX. The VBar cares only the ingoing values - shown by the bars in the pc.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 05.04.2016 05:53 von RV.
Vinger
5 April 2016 08:4405.04.2016 08:44
Thanks, we can only get values in the 0-100 range, but these seems to be fixed at an arbitrary value, tried NORMAL and AVCS modes, the diffirence with 18SZ is that there are three values available for each gain function and this seems to be ONLY coupled to flight mode switch.... Very difficult to understand the radio and the selection of gyro channel is free but no matter what we select as gyro channel ( selecting the same in Neo software) it seems to not control the actual gain values in the Neo.
Yes Neo is updated and PRO/RESCUE is active. Maybe study the TX manual for another week will work!
VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
Vinger
6 April 2016 07:4906.04.2016 07:49
OK got this sorted, Futaba 18SZ gyro channel depends on what transmission protocol gets used as this was set to SH-FHSS it will always be channel 5 irrespective of receiver programming. So changed bank switch to another channel and channel 5 for gyro and setting all the rates for rudder to NORMAL it works as it should. Just me not knowing Futuba that well resulted in confusion, but reading manuals and doing a bit of research got us sorted.
VControl, VBar on all.
TDR, TDR2, TDF, TDS and TDSF
Peter
RV
6 April 2016 10:0506.04.2016 10:05
:-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.