above
9 April 2016 18:2809.04.2016 18:28
Hello, my intention is to use the neo governor, with integrated ESC hobbywing phase sensor.
I made the connection the ESC in the FBL as hobbywing manual says.
white / red / black wires on the ESC
black / red cables AUX3
Orange RPM cable / signal
And I have adjusted the values of ESC as stated in other post I've read on this forum.
The problem is that I set various RPM in each bank and the helicopter starts at about 1600rpm approx. And does not change from RPM to change Banks.
Example: I have flown with neo castel 90 hobbywing external phase sensor and everything went perfect, the neo might not be compatible with the ESC hobbywing?
RV
9 April 2016 21:0309.04.2016 21:03
Hmmm - using a servo as a pointer instead of th esc - does the signal from the neo change with e.g. collective stick?
Did you press "reset" after enabling the gov in pc?
HW should work - but as we have none - not tested. But others say it works.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
10 April 2016 16:0110.04.2016 16:01
Yes, I've reset the governor and no works already
I try about servo and makes a soft start bud don't change the possittion if I move the banks
Instead, I try to put the servo in another neo that I've programmed with a extern phase sensor HW that works perfectly
and does the same
Can you try it with your HW ESC? I think that it's not compatible
Thanks
RV
10 April 2016 18:4010.04.2016 18:40
Quote:Can you try it with your HW ESC?
If they will send me one ...
Quote:I try about servo and makes a soft start bud don't change the possittion if I move the banks
In VGov mode the Throttle curve is determined by basic throttle and the collective ad. The Gov itself shifts it whenn running with its integral unless we have the right RPM as requested. So - if you run VGov - normal.
Does the requested HS change?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
16 April 2016 19:4516.04.2016 19:45
Hi I realized the possible failure.
I have two NEO.El that works for me either internal governor of NEO, when I connect the Hobbywing phase sensor magnet green light goes out, but when I plug in the NEO does not work the governo not quenched.
It could be that the entry of RPM does not work?
If so I have to do? I send it?
Warranty?
RV
17 April 2016 07:0217.04.2016 07:02
You can check the RPM as follows with a "Loopback test" - using the tail pulses on the bench:
- connect a single wire from tail servo out signal to RPM in (only the orange lead)
- set tail servo to 333 hz
- set sensor(poles) to 1 and gear ratio to 10
- now have a look in the main page
- which RPM is displayed?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
17 April 2016 18:2917.04.2016 18:29
RV
18 April 2016 05:5218.04.2016 05:52
Have you seen where "RPM" is printed on the label?
Use the right socket ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
18 April 2016 09:0818.04.2016 09:08
o my god !!!
epic fail !!
Thank you ! forgive the inconvenience
RV
18 April 2016 12:4918.04.2016 12:49
:-)
No problem here at all - i thought it must be something general ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.