i have more than 10 flight on this machine, running jeti R3, today i lost control, neo went to fail safe for some reason and crash the machine. No warning from Jeti TX, jeti TX log looks clean. i attached my neo log, hope somebody can help me solve this issue
← VBar NEO for external transmitters
help analyze my crash(NEO non vlink Jeti R3 receiver) translated
VBar › VBar NEO for external transmitters ·
Started by Itogs on 3 June 2016 18:5203.06.2016 18:52
Itogs
3 June 2016 18:5203.06.2016 18:52
RV
3 June 2016 20:1003.06.2016 20:10
Please add the complete log as file (zip it).
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Itogs
3 June 2016 20:4603.06.2016 20:46
ulrich
4 June 2016 00:1604.06.2016 00:16
The Message "Out of Synchronization" does appear from time to time in your log. The Message describes a Packet, that has a wrong length resp is incomplete. I am not sure which firmware version of the Rx is used. Is it a current one?
This message shall not appear during normal use, otherwise something is wrong with the Reciver or the transmission to the VBar. It may appe3ar once at startup, when a partial package is recived as first package, which usually is no problem.
There where some first implementations of UDI that had some problems with at least some settings. But this shall be rersolved in currrent versions.
so long ... Uli
http://www.vstabi.de
This message shall not appear during normal use, otherwise something is wrong with the Reciver or the transmission to the VBar. It may appe3ar once at startup, when a partial package is recived as first package, which usually is no problem.
There where some first implementations of UDI that had some problems with at least some settings. But this shall be rersolved in currrent versions.
so long ... Uli
http://www.vstabi.de
Itogs
4 June 2016 01:3804.06.2016 01:38
I have the current firmware version on my r3 v3.25, if the problem is the receiver, will it show in my jeti log? jeti log shows i dont lost any signal or no issue at all, as for wiring, it was secured by hot glue and i run my wire as short as possible. I did some testing, when i unplug my RX to Neo, for 1-3 seconds, my JETI will alarm and give me loss signal and low battery alarm, but it wont go to fail safe, if i go more than 5 seconds, it will activate my fail safe. I think i have the current neo firmware as well v6.1