RV
10 August 2016 16:3710.08.2016 16:37
Well done now!
Ok - if all sticks are held like i describe - they're fine.
Can you please (must be ziped) the setup file too - so i will load it in a VBar to check ;-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alerival
10 August 2016 17:3310.08.2016 17:33
Rainer in the conf.zip you have a bakcup configuration from my Vstabi, ready for restore in your vstabi.
Let me know if you need more info.
Alejandro
Dateianhänge:
öffnen |
Download -
conf.zip
(493 bytes)
RV
11 August 2016 00:4711.08.2016 00:47
OK - everything seems good here on the images.
I would suggest to send the NEO to our service. Please create a service request by clicking on the service icon at this device in your list.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alerival
11 August 2016 03:5511.08.2016 03:55
Hi Rainer thank you for check my configuration.
My question in reference of the log is why after my second rescue I get aleron & elevator problem ..
RV
11 August 2016 09:0511.08.2016 09:05
The sensor messages can have 3 reasons:
- the heli has moved by the pilot with a rate (e.g. during a fast flip) which is out of the sensor resolution
or
- the rescue moved it with such a rate
or
- the sensor got such signals when hitting the ground
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
alerival
11 August 2016 18:2011.08.2016 18:20
Dear Rainer are the accelerometers sensitivity en case of rescue are differents from a regular flight ?
Beacause in fly was excellent the Neo, I was in fly, I didn't detect any hint that makes me think of problems..., I test hard 3D and was all ok, I don't believe that ?
alerival
11 August 2016 20:4211.08.2016 20:42
Hi Rainer, today I detected the problem. Was heli vibration, but I don't understand why this vibration affects in rescue mode Only and not in fly.
What I did.
I put me heli in a bench and the compensation was ok, after that I went to fly test, in 3D (tip tocs, caos, pyro flips, etc.), was Ok. I return to my house and in the bench I do the same like my fly and when I shut the rescue the swaplate go right and down, like my crash.
I put out blades (main, and tials), main gear and torque tuve also, Only in the heli , the Neo, servos, and the engine, I do the same test and when I shut the rescue the same situation (alerón right and elevator pull).
After that I fastener the Neo with a seal and test again with rescue, and now the swaplate go up level.
In conclusión from my side the doble side stick is not good.
And in rescue mode it is very sensitive not so in no rescue.
Is possible to change the sensitive in rescue mode ?
Alejandro
Eddi E. aus G.
12 August 2016 08:5212.08.2016 08:52
Hi,
the sensitivity is a characteristic of the sensor element itself and can't be changed.
The gyro sensors are very robust, the rescue sensors are more sensitive, obviously.
Mind that vibration is a serious issue and does probably not only affect the sensors of a flybarless system: I had a customer report at IRCHA where said customer was able to remedy drift on his model, at a certain head speed, with tape-metal plate-tape and iirc a velcro strap around it, but a couple of flights later his torque tube type tail drive failed, probably because of the vibration (gears going bad or moving inside the tail shaft, shaft failure, crash).
Kind regards
Eddi
Born to fly ...
forced to work.
alerival
12 August 2016 13:3612.08.2016 13:36
Hi Rainer, could be possible affect the vibration in rescue mode and not in fly and do 3D ?
Alejandro
alerival
12 August 2016 13:4812.08.2016 13:48
Hi Eddi, I don't understand why in rescue mode the sensor are more sensity than normal mode ?, not make sense in reference of design..... I think every people do the same test before test in rescue mode (check the rescue in hold, fly the heli, do 3D, and if everthing is ok, go up 10 meters in hover and shut the rescue...) What I hope to do the heli level the swashplate and positive, like in hold mode, like I tested in the bench, and like my first shot up rescue).
Alejandro
Eddi E. aus G.
12 August 2016 14:3612.08.2016 14:36
Hi,
it's simple: they are different sensors, the gyros for normal flying and the accelerometers for Rescue, they have different specs.
What affects one must not necessarily affect the other.
As Rainer said: if in doubt, please send in. Maybe it's considerably cheaper to send in via your dealer than to send directly to us, though, I would take that into consideration.
Kind regards
Eddi
Born to fly ...
forced to work.