ReadyToFly
3 September 2016 16:4703.09.2016 16:47
Hello guys,
So far I've only been using the Neo governor, but now I'd like to try the CC governor and wonder how to wire and setup things, please.
My goal is to use the "governor high" mode of the CC Esc to govern the HS so that, by changing the TC on my Futaba 8FG, I'd change the HS during flight. Is it possible on Neo?
I chose "external esc gov" on the Neo software gov1 tab and tried it, but the motor won't spool up.
Can someone help, please?
Thanks.
1 mal bearbeitet. Zuletzt am 03.09.2016 17:06 von ReadyToFly.
RV
3 September 2016 18:4803.09.2016 18:48
Is the bar in the PC working?
Does a servo instead of ESC move?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ReadyToFly
4 September 2016 19:2904.09.2016 19:29
Hello RV,
Yes, the "motor" and "bank" bars in the picture move as I flick the 3 flight modes. I can't see any servo moving.
I don't know exactly what I did, but the motor is working now. However, I don't have a different HS on each flight mode. The HS is very low and the same on every flight mode.
My flight mode switch is the same for the vbar banks, i.g., SE switch on futaba t8, according to the directions on Vstabi. Channel 3 is assign to throttle on my futaba t8.
Thanks.
2 mal bearbeitet. Zuletzt am 04.09.2016 19:31 von ReadyToFly.
RV
4 September 2016 20:0804.09.2016 20:08
Did you set up different ESC percentages in the main tab for each bank?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ReadyToFly
4 September 2016 21:3204.09.2016 21:32
hello,
the bar in the picture wasn't changing as I flicked the flight mode switch.
then, I went to the gov1 tab and pressed the "reset to external" button again. now the bar in the picture is changing values as I change the flight mode. was that the problem?
do I have to press the "reset to external" button on gov1 every time I change the TC on the radio (I'm using the "governor high" mode on CC, not the "set rpm" mode!)?
thanks.
1 mal bearbeitet. Zuletzt am 04.09.2016 21:33 von ReadyToFly.
RV
4 September 2016 22:2504.09.2016 22:25
- where is the bar at "stop"?
- where at "run" in Bank 1,2,3?
- Where in "idle/auto"?
is the Motor switch configured fully according to our manual with its 3 states (off, idle/AR, run)?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ReadyToFly
5 September 2016 00:1105.09.2016 00:11
hello,
- where is the bar at "stop"?
flipping the TH switch doesn't affect the bar at all.
- where at "run" in Bank 1,2,3?
on the bar the value change from to 40 to 50 and then to 60, for idle 1, 2 and 3, respectively.
- Where in "idle/auto"?
I don't have idle/auto configured. On my futaba I have throttle on channel 3 assigned to my throttle stick, just like a normal radio. I did that because I'd like to run the "governor high" mode on the CC ESC. With "governor high" I need to have a regular throttle channel, with 3 throttle curves set on the radio. What I'm trying to do here is having the ability to change HS by changing TCurves on the radio, just like I used to do with Silverline.
My settings are the same as
http://www.vstabi.info/en/node/1946, except for ch3, that is assign to throttle and j3 (stick) on my futaba.
I wasn't able to attach the settings file.
Thanks.
2 mal bearbeitet. Zuletzt am 05.09.2016 00:13 von ReadyToFly.
RV
5 September 2016 10:3705.09.2016 10:37
OK - so ... where is the ESC Master connected to the VBar? Which socket?
Note: It is not our intention to use a stick-driven spoolup (not needed with a governed esc, relict from non-governed ESC stone age!) through ESC out on the NEO.
What you are doing can be done with "AUX3" (See advise for 3rd party radios here) - but from then on we're out - it is the pilots and radios deal to handle the throttle. Of course we need the motor status signals anyway ...
Time to go one of these:
- use AUX3 and own TX settings
- use the ESC spoolup and ESC
- use VGov and its spoolup
(in all cases our motor states stop/Idle/run must be set according to your usage!)
Or - as best
- use VGov and a VBar Control instead of other Radios.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 05.09.2016 10:42 von RV.
ReadyToFly
6 September 2016 20:1506.09.2016 20:15
hello,
unfortunately I couldn't make things work as desired here.
are you guys somehow "studying the possibility" of allowing Neo to see the radio's TC one day?
thanks.
1 mal bearbeitet. Zuletzt am 06.09.2016 20:17 von ReadyToFly.
RV
6 September 2016 22:2806.09.2016 22:28
Please read and follow the AUX3 chapter here for old style usage ...
http://vstabi.info/en/neo_transmitter
It should be possible, we just pass AUX3. If it won't work - connect a servo as a pointer for a check. If this works - check ESCV configuration.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ReadyToFly
7 September 2016 12:5207.09.2016 12:52
hello,
i actually got it to work, but, as i said before, not "as desired".
the problem is that Neo won't recognize the new HS after i change a TC on the radio. i have to press the button on the gov1 tab for it to happen. pressing the button on the software every time i change a TC curve on the radio "kills" the whole idea of controlling the TC curve on the radio. it is regrettable.
you guys keep saying "old style". it isn't true and fair. doing things differently from mikado isn't old fashioned in any way. the mikado way isn't necessarily the best way.
take a look at the goblins, for example. they have a square boom and a very different look. i bet they thought every manufacturer would follow them, but none did. all other brands kept their tubular tail boom, thanks God.
not every new approach is necessarily better than the previous one. in this particular case, Neo is denying me, the customer, the ability of using a given feature of an ESC. i mean the "governor high" mode of CC.
i have 3 logos and a silverline that i love. i have 4 neos. i also have a vcontrol that i don't like.
i'll keep trying here, but i don't believe i'll get there.
thanks.
1 mal bearbeitet. Zuletzt am 07.09.2016 12:53 von ReadyToFly.
RV
7 September 2016 23:1407.09.2016 23:14
Did you use the AUX3 method? - i am afraid - not.
Your ESC seem to be connected to "ESC" ... and not AUX3.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
8 September 2016 08:2808.09.2016 08:28
Hi,
to clarify: if you connect the ESC to AUX3 and assign the throttle channel from your radio to AUX3, all is as it was before, direct control for throttle, from the radio. The only thing you want to do, then, too, is assign a separate channel to the motor channel and switch it with your throttle, so the VBar knows when the model is driven (motor running at speeds to maintain a flyable head speed) and when not (motor off in autorotation or motor idling but not fast enough to drive the rotor.
Although we find our approach 'more modern', we leave the back door open for 'old school', nothing wrong with it.
Kind regards
Eddi
Born to fly ...
forced to work.
ReadyToFly
9 September 2016 22:1409.09.2016 22:14
hello guys,
what is wrong here, please?
thanks.
RV
10 September 2016 07:5410.09.2016 07:54
x6 is wrong.
Is there a "AUX3" function in TX (!!!) to drive the Ch3 ??? - I think NOT.
NOTE: The Name "AUX3" in TX has NOTHING to do with our VBar Output called "AUX3". The Channel which is given out in VBar is determined in the RX tab (here Ch3) - and the TX function to drive this Ch is set in TX - and i think you must enter "THROTTLE" here ...
Would be way more easy with a VBC ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 10.09.2016 07:55 von RV.