← VBar NEO for external transmitters

Fast oscillation rudder Trex 500 translated

VBar › VBar NEO for external transmitters · Started by pequeño159 on 27 September 2016 19:5827.09.2016 19:58
pequeño159 27 September 2016 19:5827.09.2016 19:58
Hello, I can not solve a rapid oscillation in the rudder Trex 500 Dominator:

Motor Align RCM-BL500MX 1600KV
Servo Align DS525M
Castle Talon 90 governor mode at 2500 RPM


When in hover, everything OK. But when I apply full collective (positive or negative), It makes a very rapid oscillation in the rudder, about 5 hz, and a small drift in torque direction.

The expert parameters are dafault.
Tail rotor gyro gain 60 or 65 is the same.

Which can be the solution:
up or down acceleration?, P gain?, I gain?

Thanks!!
RV 27 September 2016 21:3827.09.2016 21:38
Did you dial in the collective torque compensation already?

In which direction does the nose move on first wag?

Is it VGov or Castel Gov mode?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
pequeño159 28 September 2016 00:1928.09.2016 00:19
Hi Rainer Vetter

I uploaded the compensation of torque and no changes

I do not know that side moves first, the oscillation is very fast and very short. Is not rotated more than a few degrees

Is Castel Gov mode, with the setup recommended by Castel for Align motor´s

Regards
Eddi E. aus G. 28 September 2016 08:4228.09.2016 08:42
Hi,

would it be possible that something binds under load? For example I had similar issues and found my tail shaft dirty and sticky, cleaned it, all was well again.

Kind regards

Eddi

Born to fly ...
forced to work.
pequeño159 28 September 2016 23:3728.09.2016 23:37
Hi,

That is not the problem.
The heli worked ok with another Gyro, change by VBar Neo to use the Rescue. It was here when I started having this problem.
so I assume it's a problem of tail settings
the current values are:

Giro Gain: 60 (with 65, same problem)
Acceleration: 55
P Gain: 80
I Gain: 60
D gain: 0

These values are default, which would be approximately correct for Trex 500 2500RPM?

http://www.rchelination.com/flybarless-tail-tuning-with-v-barlogo-example/


Thank you very much!!
RV 29 September 2016 10:0229.09.2016 10:02
Can you try to use a non-governed mode in ESC to exclude a gov issue?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless