← VBar NEO for external transmitters

TM1000 Telemetry always in bind mode translated

VBar › VBar NEO for external transmitters · Started by marcelftw on 20 February 2017 17:3920.02.2017 17:39
marcelftw 20 February 2017 17:3920.02.2017 17:39
Hello guys,
I'm actually a native german speaker but I am going to make an english thread, in case someone has the same issue.

So I have a DX9 and a VBar Neo with the TM1000 Telemtry system. I'm binding everything properly and it works, but for some reason just for one season. Whenever I disconnect the Battery and everything gets restarted the Telemtry Unit will go into bind mode by itself again. If I disconnect the Power between the TM1000 and the FBL and reconnect it, it takes a few seconds and has a stable connection until I disconnected the main battery again. I made a little video where everything is shown.

https://www.youtube.com/watch?v=aE5Dpn50rc0

And btw, dont worry about the laggy DX9 interface, it's a really weird bug but doesn't effect the problem.

In case anyone has a clue whats wrong, or has a hint, please let me know :-)
RV 20 February 2017 18:5220.02.2017 18:52
Where is the TM connected to? Is ther a signal wire connected? - If yes - plese remove this wire from the plug for a test ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
marcelftw 20 February 2017 20:1420.02.2017 20:14
The TM is connected right to the Neo. And what do you mean with signal wire? there is obviously a wire transfering data/signal, but if I remove it, it wont have power.
RV 20 February 2017 20:1520.02.2017 20:15
Are there 3 Wires or two?

Which Socket on NEO?

can you please add a photo?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
marcelftw 20 February 2017 22:1120.02.2017 22:11
TM has 3 Connectors, Data (goes in AUX1, Neo), RPM (from ESC) and Volt/Temp on a Y-Cable.

And I have provided a video above, where you can see the whole binding to restarting process.
RV 21 February 2017 05:4821.02.2017 05:48
Well - i cant see it clealy there - please take a photo of the connector at AUX. Does this have a signal wire or not? - If yes - remove it. It must work with the remaining 2 ones (+ and -) i think.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
marcelftw 3 March 2017 21:1603.03.2017 21:16
Sorry for the late response, I haven't been able to see the heli though.

How am I suppose to remove the Signal wire? I can't just pull it out, or else I will break the connector. I might be misunderstanding you maybe.

RV 3 March 2017 21:2103.03.2017 21:21
If you can't pull ist - just insert a short servo extension cable in between and cut/pull it there ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
marcelftw 3 March 2017 22:4503.03.2017 22:45
Oh my god, thank you so much, it works now. It doesn't go into bind mode anymore.
Thanks <3
VStabi VStabi Pioneer of Flybarless