← VBar NEO for external transmitters

Mikado, Please upgrade NEO cases translated

VBar › VBar NEO for external transmitters · Started by Heili$ on 10 February 2017 04:4510.02.2017 04:45
Heili$ 10 February 2017 04:4510.02.2017 04:45
Mikado, please update the NEO cases so they are tough. I just received a brand new NEO and the case was cracked right out of the package. These cases are like egg shells and the tabs crack very easily. My Nitro helicopter cracked the tabs several months ago. Now, I have the NEO ZIP TIED DOWN. People are resorting to all kinds of methods to keep these cases from breaking including heat shrink and after market products.

Also, figure out a way to keep the boards from wiggling inside the case. There should be absolutely no play with the boards inside the case.

AMAIN hobbies is currently sold out or version 2 replacement cases. No other flybarless company sells just the case unless it's an upgrade. This is a clear signal that pilots are having to replace these inadequate cases.

Thank you
MH 27 February 2017 14:0627.02.2017 14:06
+1
slowrider 27 February 2017 17:2327.02.2017 17:23
+1

I killed two cases in my quad racer so fare...
mc20piece 2 March 2017 17:1602.03.2017 17:16
+1

This absolutely needs to be addressed. I'm tired of replacing them.
Eddi E. aus G. 3 March 2017 08:5403.03.2017 08:54
Hi guys,

just checking in to show that we are reading your requests.

At our end (and we are flying the NEO a lot, too, on all sorts of models, including nitro, gasser, turbine) we hardly ever have to replace a case unless we damage it accidentally (crash damage or broken when removed from a model, putting force to the wrong (top) end.

So I would be curious about more background info: what type of models, mounting position, under what circumstances did it happen?
And please be truthful, it's not about blaming anybody for anything, it's about finding out what causes it or if there are 'procedures' which people out there follow, which could damage the closing tabs, or if it's really 'stick on, connect, set up, fly, pop goes the cover' although it's handled gently.

From what I get so far I must assume it happens mainly on nitros. But from the design of the tabs, and if they are OK, it should not be possible.

Regarding the axial play of the main board inside the case, at first the boards were fixed softly, with dampening, with adhesive pads.
This also allowed to compensate for slight production tolerances which can not be eliminated fully.
In the meantime we have changed the case (V2 type for the unified hardware), and the covers and antenna outlet covers are modified in a way so they bind the main board on closing the case. The V1 replacement cases also sport these features on the cover and back cover, only the lower part remained to accommodate the two-pcb-design.

But by my experience, both mechanisms worked and work reliably. The comparison to an egg shell is good, like an egg it's pretty sturdy for what it's designed for, to keep inside what's inside, but if you have the first crack in it, it goes ... on the positive side, it's as small and light as can be.

We discuss it here, too, let's see what we can come up with. All your input is appreciated :-)

Kind regards

Eddi

Born to fly ...
forced to work.
WFEGb 3 March 2017 09:4403.03.2017 09:44
Hello Eddi,

just to jump in with three thoughts. (Only nitro-helis (one with turbine), two Vstabi 5.3.4 and three NEOs bought new and used ones...)

- My old cases are stable and fitting without any play with their inlives. I don't care about.

- At least a new NEO should not show any "feelable" tolerance between inlive and case. No matter about production tolerance. You should find a way to eliminate them. Because they do. Ok I do trust you, it won't matter, but the feeling around is not as trustworthy as with the old ones.

- If the user is allowed to open the case, the tiny clips inside should not break at the first opening attempt...

OK that's not statistic with great numbers, but if any possible you should avoid having only single talks about that on the flight-fields anywhere, because this will keep a pilot here and there from buying a NEO. And this can not be your main interest.

Best regards,
Werner
Eddi E. aus G. 3 March 2017 11:3303.03.2017 11:33
Hi Werner,

thank you for your input. With V2 (and the replacement cases for V1) the play should be eliminated without additional measures.
And with V1 I'm pretty sure it was OK with most of the devices, with the padding.
Granted, play is not good and doesn't give a good feeling to it, even if it's more or less eliminated as soon as the connectors are in.

The user is usually only allowed or put better, required, to open the case when retrofitting or replacing antenna wires, but he might damage the case, and since the clips are fragile even if not I would do it: if the plastic gets overstressed to a certain degree it may break more easily.
This is why we offer the upgrade kit with a case, just in case. Also, the label usually gets damaged since it covers both sections.
This also goes for the case where you grip the NEO at the top and wiggle it off the tape, it's better/safer to pry it off the tape with a screwdriver or other suitable tool.

A question to all, if I may: please state if it was blue NEOs where it happened, V1 or V2, or if it was white NEOs.

Kind regards

Eddi

Born to fly ...
forced to work.
Freeskiken 26 March 2017 06:2926.03.2017 06:29
The Blue Neo cases are very fragile. I bought two used Neo Vlink that the tabs were broken. You had to remove the label to see the broken tabs. Scratches on the bottom of the cases indicated they used something to pry them off. Other people on forums have indicated the same that they break very easy. One of the new replacement cases I bought the top was cracked from new. On the plus side they are easy to replace. I found the only way to remove the Neo with out damaging it is to use fishing line and two pieces of wood for handles move side to side to saw it off.
Eddi E. aus G. 27 March 2017 08:5927.03.2017 08:59
Hi,

if I have to remove a NEO, I use a thin screwdriver or similar to go between chassis and pad, and pry it off as gently as possible.
Have done the same also with Minis and Standard VBars in the past.

From new shouldn't happen though, in case you find that please document right a way with a pic or two and contact us or your dealer ...

We are on it, checking options.

Kind regards

Eddi

Born to fly ...
forced to work.
VStabi VStabi Pioneer of Flybarless