← VBar NEO for external transmitters

Neo + Hobbywing 130 HV translated

VBar › VBar NEO for external transmitters · Started by gbraeckmans on 2 May 2017 21:2502.05.2017 21:25
gbraeckmans 2 May 2017 21:2502.05.2017 21:25
Hi,

I’m having a hard time setting up a Platinum 130 HV ESC in the following configuration:

Logo 690 SX
Vbar Neo Express with pro upgrade + 2 Spektrum satellites
Scorpion 4525-380
Savox servos
Spektrum DX7 v2 transmitter
12 cell setup

I have sent this also to Hobbywing support, waiting for their answer. Problem is mostly with Hobbywing but I have some Neo questions as well.

Neo and ESC both have the latest firmware. The ESC endpoint calibration was done. The rpm sensor connector to the Neo is NOT connected.

First I wanted to tune the heli without any governor. I set it up in heli linear mode. 12 cell was configured. BEC voltage 6v. The rest of the settings were default. In the Neo, the throttle out was set at 70%, in bank1, the active bank (the Neo does not listen to the transmitter throttle curve).
The moment I switch off throttle hold, the heli spools up and immediately does a violent tail kick to the right. I tried all kind of startup power settings, nothing helped. Various forums suggest turning of AFW or setting the ESC in fixed wing mode. This did not help and I do not want to do this anyway as I fly a rather low headspeed, so AFW is useful here.
The only way I can avoid the violent tail kick is to set the ESC in governor store mode. This brings me to the second problem.
The ESC governor needs to learn the max headspeed. This is done by setting a 50% flat throttle curve in the transmitter (blades need to be on the heli). But since the Neo does not look at the transmitter throttle curve, I set the throttle out value in the vbar to 50% (first bank and active bank). When switching off throttle hold, nothing happens. The heli does not spool up. I think this is because the Neo needs +50% throttle before is does a spool up (is this correct?). When I switch to bank 2 where the throttle out is 80%, the heli does spool up.
I then switched on throttle servo adjustment in the gov II tab of the Neo. Then I could go to 50% throttle via the stick and let the ESC learn the headspeed. However, I fear that this is not the correct way of doing it as you are not supposed to touch the throttle stick when the ESC is learning the headspeed. So how can I do the learning of the headspeed correctly? And how can I verify what value the ESC learned?
When I set my throttle values in the Neo at 75% bank1, 80% bank2 and 85% bank3 and set the bank switching to my flight mode switch. The heli seems to react as expected but I’m not sure if the learning is done correctly as I cannot do the procedure as it is supposed to be done.
So for the Neo specialists: can I put the Neo in such a mode that it outputs 50% throttle like a 50% flat throttle curve.
My third question is about using the Neo governor. Here the same problem exists with the violent tail kick. Heli forums are full with this problem. It exists for months, yet apparently there is no fix in the making.
Again, I realize this is mostly a Hobbywing problem as other fbl brands have the problem too but maybe somebody here has a solution for the Neo.
I would appreciate any help as I’m pulling my hair out trying to solve the problem.

Kind regards,

Guy
RV 2 May 2017 22:0602.05.2017 22:06
OK - we expect either a ESC Gov (external Gov - 3 linear throttle values in flight panel, one each bank and one for AR) or a VBar Gov.

We do not support other "historical" throttlecurve driven modes.


Quote:can I put the Neo in such a mode that it outputs 50% throttle like a 50% flat throttle curve.

Set Gov1Tab to external, enter values each bank in main page.



Quote:So how can I do the learning of the headspeed correctly? And how can I verify what value the ESC learned?

Quote:My third question is about using the Neo governor. Here the same problem exists with the violent tail kick. Heli forums are full with this problem. It exists for months, yet apparently there is no fix in the making.

Hmmm - can't help you - i don't use HW. Anyway - HW has Mirko Cesena as teampilot and he knows both - VBar Neo and HW ESC - maybe they can forward your request to him.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
gbraeckmans 3 May 2017 19:3103.05.2017 19:31
Hi Rainer,

thanks for your reply.
I did get an answer from HW today but it was far from acceptable. We'll see how it plays out.
The strange thing is, when I put 50% throttle out in the Neo on bank1, make sure this is the active bank, the heli does not spool up. If I set it to, for example 75%, the heli does spool up. This makes me think there is some minimum value that is active somewhere and you need to be higher than that. But I have no idea where or what it is.
If I could use the Neo gov, which I prefer, this would not be a problem but HW does not seem to want to fix the tailkick problem. This kick is really violent and dangerous so there is no way to just live with it.
I'll try testing some more this weekend if I can take the heli out. I'll post back when I know more.

Rgds,

Guy
RV 3 May 2017 22:0903.05.2017 22:09
Could you link the manual from HW here? - so I'll have a look ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
gbraeckmans 4 May 2017 13:3404.05.2017 13:34
This is the link to the manual:
http://hobbywing.com/goodsshow.php?id=512

this is the very elaborate and helpful reply I got from HW:

Dear sir:
If you use the flybarless system governor ,please set the ESC flight mode is Fixed wing , set the Acitve FW is disabled .

If you use our ESC governor , please turn off the flybarless system governor .

After I specifically said I don't want to disable AFW, I use low headspeed. They should just fix the software.
RV 4 May 2017 23:2404.05.2017 23:24
Ok - about the % Values:

Quote:In “Helicopter (Elf Governor)” mode, the motor will start up when the throttle amount reaches
40% or above

So - your statement here is right:

Quote:When switching off throttle hold, nothing happens. The heli does not spool up. I think this is because the Neo needs +50% throttle before is does a spool up (is this correct?). When I switch to bank 2 where the throttle out is 80%, the heli does spool up.

The values might be a bit different (depending on the teaching process of throttle) - but are just numbers.


I would use the ESC gov in your case and try to figure out the lowest % Value where it will start and fly (set to 40, turn on and increase unless motor starts).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
gbraeckmans 6 May 2017 10:2606.05.2017 10:26
Hi Rainer,

Thanks for your help. I'll stick with the ESC governor for now. If they don't fix it in the near future I'm going for the Scorpion Tribunus 130 HV when it comes out in a couple of months.
hanspi 3 June 2017 12:4303.06.2017 12:43
Hallo

seit über 2 Stunden versuche ich den Gasweg einzustellen mit dem Vstabi. Es ist der Align 130 A ist ja identisch mit dem HW. Motor auch der Align 850.

Ich kann einstellen was ich will der Motor schaltet immer erst bei ca. 60 Gasweg ein. Eigentlich wollte ich fliegen und nicht programmieren.

Grüsse
Hanspeter
Fingolf 3 June 2017 13:0403.06.2017 13:04
Hast entsprechend der Regler Anleitung eingelernt?

Stephan
RV 3 June 2017 15:2503.06.2017 15:25
Bitte sepeareten Thread aufmachen - KEIN THreadnapping!

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless