← VBar NEO for external transmitters

Strange cyclic on end points translated

VBar › VBar NEO for external transmitters · Started by recovery on 26 October 2017 18:3226.10.2017 18:32
recovery 26 October 2017 18:3226.10.2017 18:32
Hello,

i finish setup of my NEO pro and i have a problem with my cyclic on end points, see video :https://youtu.be/bjq0YYEmuCo

When i m in setup, my cyclic is ok.

My setup is Goblin 570, Vbar NEO pro, 3 RJX FS-0521HV on cyclic, X8 on tail, Himodel 120A, quantum 560 and Futaba T18SZ

Thx for your help (sorry for my poor english)
RV 27 October 2017 07:4327.10.2017 07:43
Having a NEO wit 6.x control loop - this is normal on the bench in flight mode ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
recovery 27 October 2017 22:4327.10.2017 22:43
Thank you of your explanation

Now i have ESC doesn't start before 60 % when i move my stick, my idle up is at 70 % and 80% and it's the same rotation on both. I choose external governor but nothing change.

Thx for your help.
RV 28 October 2017 08:4928.10.2017 08:49
Keep note that in our flight modes the stick position doesn't care.

We just toggle the Motor switch from OFF to RUN (AR is in center) - and the motor runs. You can see this by watching the throttle bar in PC or adding a servo instead the ESC as a pointer. If this works at our bar and also it represents different values there - all is ok on our side. Maybe a ESC issue then.

And - about start at 60% - AFAIK it is so at some ESC (HW), have a look at their manual.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 28.10.2017 08:50 von RV.
recovery 28 October 2017 23:0928.10.2017 23:09
My ESC is a himodel like an YGE.

Watch this video https://youtu.be/inoYWr3rSBs

In start my curve is -100 +100, throttle bar move "stop" and "idle" and start à "run" and governor bar start on same time (indicate 0 before "run&quot ;-)

if i active my 1 idle up in my Futaba, motor run as the value of "throttle out", idle 2 change nothing gov bar don't change.

if i want 2 idle up i need to modify "throttle out" value on 2 bank, is it right ?

Is it possible to fly with out Gov ?

If i understand well, i can for normal throttle active gov2 on on bank and on 2 last bank make my idle up or use aux 3 on NEO and setup for use radio parameter.

Thx



2 mal bearbeitet. Zuletzt am 29.10.2017 08:45 von recovery.
RV 29 October 2017 13:1229.10.2017 13:12
This is quiet normal.


We expect a ESC which:

- goes with a internal Gov (your setup here), spools up soft by flipping the switch from stop to run at zero collective. YGE Gov or Gov Store mode is the right one.

OR

- goes with VBar Gov and has a RPM signal - YGE has a mode here which gioves a RPM on slave as well ans does a soft start and then fade over to our gov.


A "Non-Governed" ESC with a manual spoolup need is not supported.


Her - in your case - for 3rd party radios - use AUX3 method to get full TX control but still feed our motor states so NEO knows about that to switch different controls internally. This may require a additional channel.

http://www.vstabi.info/en/neo_transmitter

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




2 mal bearbeitet. Zuletzt am 29.10.2017 13:15 von RV.
recovery 29 October 2017 23:1329.10.2017 23:13
With AUX 3 now all work

THX
recovery 31 October 2017 23:2831.10.2017 23:28
But ... not sure my configuration is right, i put ESC on Aux 3, in Neo write Aux 3 on channel 3 as motor, if i need on more channel i think that not ok.

I think i need to put motor on other channel for autorotation and put it on switch (same as my autorotation)

- Motor Stop = Autorotation
- Motor IDLE = fly

it's right ?

My problem is on a switch 3 positions, i m sure need to stop and run :-(



2 mal bearbeitet. Zuletzt am 01.11.2017 00:27 von recovery.
RV 1 November 2017 10:1501.11.2017 10:15
We need as status in our Motor input channel:

- Off (-100% from TX)
- AR (is IDLE in PC) (0% from TX)
- Run (100% from TX) (for flying)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 01.11.2017 10:15 von RV.
VStabi VStabi Pioneer of Flybarless