← VBar NEO for external transmitters

Neo Gov. crazy over speeding translated

VBar › VBar NEO for external transmitters · Started by joecass on 28 October 2017 01:5928.10.2017 01:59
joecass 28 October 2017 01:5928.10.2017 01:59
I’m flying a whiplash gasser and when unloading the head I get a lot of over speeding. It Really revved the engine high especially after doing A set of tick-tock‘s.

Collective add 40
Basic 32
Min limit 5
Gain is 30
Diff is 0

I have tried lowering collective add to 30. It seems like it fixes it for a little bit but then it will start doing it again. If I’m flying it at 1800 and then unload the head it will shoot up to 2100 for about 15 seconds.

I have also tried moving the main gain from 60 to 20 with not much difference 30 seems to be were it works the best.
RV 28 October 2017 08:5228.10.2017 08:52
Have you already followed my guide here for setup:

http://www.vstabi.info/en/node/2030

(VBC recommended)

BTW:

If the add is too low - it could be nearly a equal effect depending on which part of the control loop comes up. Maybe the Integral comes up at far too low ads and this is the slowest one ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 28.10.2017 08:54 von RV.
joecass 28 October 2017 17:5528.10.2017 17:55
Ok so I tried setting it up as per the info you gave me. I found that I have to use a lot of basic 55 and 25 on add. I can still use to come down on add a little more this is for bank 1 set up to make it to 1600 RPM head speed. I have my throttle linkage set up like Malories set up. Should I change this to a more linear throttle linkage setup?
RV 29 October 2017 13:0729.10.2017 13:07
On a gasser i set up the throttle like this one here:

https://rc.runryder.com/helicopter/t105349p1/?p=3504262#RR

This gives a "linear" response (but a non linear linkage).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass 29 October 2017 13:5129.10.2017 13:51
That is how I have my throttle linkage set. Is it ok that my basic is 55 and my collective add is 25? I didn’t think you were to have the basic number higher then the collective add.
RV 29 October 2017 14:3429.10.2017 14:34
Well - they are just numbers. Just try in the air ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass 30 October 2017 20:0930.10.2017 20:09
So I set heads speeds up perfect with the gains at 0 using basic and add. Still over speeding so I bumped the gain from 25 to 50 this had no effect on it. Is there anything else I can try?
My basic is 59 and add is 25
RV 31 October 2017 11:1131.10.2017 11:11
Is there a U/I Log from the VBar Control available where we can see PWM, Amps and RPM? (Requires VBC and UI Sensor)

At all - is it a ROTOR or a MOTOR Overspeeding? - You might listen tor ROTOR which runs in the freewheel ... so Gov changes won't help.

- What does the RPM Display in VBC show there at this situation?
- What does the Throttle bar in VBC show there in ithis situation?
- What is in the event Log in this situation (might be min Limit)?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass 1 November 2017 03:1901.11.2017 03:19
I’m not using VBar control. I’m flying it with futaba TX.
The log is clean just some high vibration logs.
I have a futaba sensor on the main gear so I can see rotor RPM. When unloading the head I can watch the head speed go from 1800 to 2100 RPM for a good 30 seconds or so.

So today when I was flying I set the diff. From 0 to 15 and the overspeeding stopped for one tank but when doing tic toc the tail started kicking so I dropped it down to 5 and it seemed good. I only got to fly it for a half tank like that so I need to fly it more to be sure it’s fixed.
RV 1 November 2017 10:1701.11.2017 10:17
Ok - the diff part is a very fast but short-temed control part. Interessting it works here.

Which motor and heli is it?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
joecass 1 November 2017 12:0201.11.2017 12:02
Whiplash with TRM 310 engine it’s the newest engine by TRM.
VStabi VStabi Pioneer of Flybarless