← VBar NEO for external transmitters

Neo Governor Settings (Gear Ratio) translated

VBar › VBar NEO for external transmitters · Started by ronaldst on 19 May 2018 23:3319.05.2018 23:33
ronaldst 19 May 2018 23:3319.05.2018 23:33
I got a GAUI X7 with a 520kV motor, 10T pinion on motor, main gear on helicopter is 100T. I have probably messed up something in the settings.

I can not hear any difference in RPM when switching banks. Castle 160HV log is showing full throttle at about 2300RPM continously.

Bank 1 is set to 1900RPM
Bank 2 is set to 2000 RPM
Bank 3 is set to 2100 RPM

Neo logs are showing this in Bank 1
Warn 7:38 Governor Full Throttle

What should gear ratio be set to?

I have used the expert icon in Neo Setup, and choosen pinion/main gear, and thought that was sufficient..



But after a closer look I see that the Gear Ratio in the main/easy setup was showing 11.78. I changed this to 10.



Is this correct?

Could this be the cause of my motor running at max RPM before?

Documentation on Vstabi is not good enough. I need some assistance here.
RV 20 May 2018 09:4620.05.2018 09:46
Well - the Expert page is only a calculator - the values must be set of course ad you did now.

Which HS was displayed in the VBC /Giv Info Panel at the same time when CC logs 2300? Depending on the answer it could be a reason or not ...

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ronaldst 20 May 2018 11:2320.05.2018 11:23
I was not aware. These things aren't explained anywhere, the documentation show some old interface pictures and is a complete mess in certain areas.

I don't have a VBC.

The governor was definitely not working on my flight. Pitch pumps, climbouts etc. did not show any sign of being governored.

Isn't the gear ratio -settings related to the RPM issues?
RV 20 May 2018 14:2420.05.2018 14:24
If you would spool up the heli w/o blades on the bench - and then measure the RPM externally as well as reading from the PC main screen Governor section - is it ok then?

If not - post a screenshot of this screen and add the full log as well ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ronaldst 20 May 2018 14:3420.05.2018 14:34
I don't have any tools to measure the RPM externally right now.

Prior to the flight I did spool up the heli on the bench, and I could hear a difference in RPM when switching banks. This doesn't mean the RPM was correct, but there was some headroom for more power to be sent to the motor.


Here's a log of the flight
OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
OK 0:15 Good Health Message (10sec)
OK 0:25 Good Health Message (10sec)
OK 0:35 Good Health Message (10sec)
OK 0:45 Good Health Message (10sec)
OK 0:55 Good Health Message (10sec)
OK 1:05 Good Health Message (10sec)
OK 1:15 Good Health Message (10sec)
OK 1:25 Good Health Message (10sec)
OK 1:35 Good Health Message (10sec)
OK 1:45 Good Health Message (10sec)
OK 1:55 Good Health Message (10sec)
OK 2:05 Good Health Message (10sec)
OK 2:15 Good Health Message (10sec)
OK 2:25 Good Health Message (10sec)
OK 2:35 Good Health Message (10sec)
OK 2:45 Good Health Message (10sec)
OK 2:55 Good Health Message (10sec)
OK 3:05 Good Health Message (10sec)
OK 3:15 Good Health Message (10sec)
OK 3:25 Good Health Message (10sec)
Info 3:28 Governor Mode Pitch
Info 3:28 Motor Switch operated to ON
Info 3:29 Governor OFF
Info 3:29 Motor Switch operated to OFF
Info 3:38 Governor Mode Pitch
Info 3:38 Motor Switch operated to ON
OK 3:48 Good Health Message (10sec)
OK 3:58 Good Health Message (10sec)
OK 4:08 Good Health Message (10sec)
OK 4:18 Good Health Message (10sec)
Critical 4:22 Extreme Vibration Level
OK 4:32 Good Health Message (10sec)
OK 4:42 Good Health Message (10sec)
OK 4:52 Good Health Message (10sec)
OK 5:02 Good Health Message (10sec)
OK 5:12 Good Health Message (10sec)
OK 5:22 Good Health Message (10sec)
Info 5:26 Raised Vibration Level
Info 5:30 Bank 2 Loaded
Info 5:35 Raised Vibration Level
Info 5:40 Bank 1 Loaded
Info 5:45 Raised Vibration Level
OK 5:55 Good Health Message (10sec)
OK 6:05 Good Health Message (10sec)
Info 6:12 Raised Vibration Level
Info 6:21 Raised Vibration Level
OK 6:31 Good Health Message (10sec)
Info 6:38 Bank 2 Loaded
Info 6:40 Raised Vibration Level
Info 6:42 Bank 3 Loaded
Info 6:44 Bank 2 Loaded
Info 6:47 Bank 3 Loaded
Info 6:48 Bank 2 Loaded
Info 6:49 Bank 1 Loaded
Info 6:49 Raised Vibration Level
Info 6:55 Bank 2 Loaded
Info 6:58 Raised Vibration Level
Info 7:00 Bank 3 Loaded
Warn 7:05 Governor Full Throttle
Warn 7:06 Governor Full Throttle
Info 7:07 Bank 2 Loaded
Info 7:07 Raised Vibration Level
Warn 7:14 Governor Full Throttle
Warn 7:15 Governor Full Throttle
Info 7:16 Raised Vibration Level
Info 7:16 Rescue has been activated
Info 7:17 Rescue has been completed
Info 7:19 Bank 1 Loaded
Info 7:26 Raised Vibration Level
Warn 7:29 Governor Full Throttle
Critical 7:35 Extreme Vibration Level
Warn 7:38 Governor Full Throttle
Warn 7:43 Governor Full Throttle
Info 7:44 Raised Vibration Level
Warn 7:44 Governor Full Throttle
Warn 7:48 Governor Full Throttle
Info 7:53 Raised Vibration Level
Warn 8:02 High Vibration Level
Warn 8:11 High Vibration Level
Info 8:20 Governor OFF
Info 8:20 Motor Switch operated to OFF
Info 8:21 Raised Vibration Level
Critical 8:30 Extreme Vibration Level
OK 8:40 Good Health Message (10sec)
OK 8:50 Good Health Message (10sec)
OK 9:00 Good Health Message (10sec)
OK 9:10 Good Health Message (10sec)
OK 9:20 Good Health Message (10sec)
OK 9:30 Good Health Message (10sec)
OK 9:40 Good Health Message (10sec)
OK 9:50 Good Health Message (10sec)

Screenshot of the ESC log
https://sharplr.com/images/2018/05/20/3xOSc.png





2 mal bearbeitet. Zuletzt am 20.05.2018 14:38 von ronaldst.
RV 20 May 2018 17:0120.05.2018 17:01
Please do a bench run as requested in all 3 HS and take a screenshot of the PC software at each HS to post it here. I want to see the Governor display values and status LED's there ;-)

Posting CC logs - the Throttle input and the RPM would be inportant to see.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
ronaldst 21 May 2018 20:5921.05.2018 20:59
I'm just going to cut to the chase here. I've done another flight today, and to answer the original question in the first post: YES the gear ratio being misconfigured was the reason the governor was all bent out of shape.

I got a 10T pinion and 100T maingear, which makes it really easy to calculate to 10.0 in gear ratio.. So I knew something was not right when I saw gear ratio being 11.47. If I had any other combination of pinions/gears I would probably not have realised it was wrong (after typing in the correct numbers in the expert menu repeatedly).

To me it was not obvious that the expert menu was just a calculator, and the settings do not transfer over to the governor gear ratio setting automaticly.

The documentation is, once again, completely rubbish with outdated pictures and non-obvious settings aren't explained in a understandable manner.

Dear Mikado/Vstabi...
I am going to point this out once and for all. The Vstabi homepage, including the forums (which does not offer a proper translated english version) have a poor layout, is really hard to navigate, and is lacking in most areas.

Most of the documentation is containing outdated naming (of settings etc.), poorly written descriptions, and old pictures (which newer Neo users can't relate to).

The FBL is awesome, and is the only reason I keep banging my head towards the wall trying to figure stuff out on my own, or through forums like Helifreak.
VStabi VStabi Pioneer of Flybarless