I apologise its a bit of an essay! This install was over 2.5 days, so i was not rushing.
I bought a Neo as I need the rescue feature.
Registered and upgraded everything and paid more money.
Removed the Spartan VX1n and did a step by step install into my 700n.
I used these settings to set up the 14SG T8 Setup even though its for a T8, 99% of it works. I have watched the videos from Mr Mel, read everything I can find, but i cannot get the governor to work properly.
Also the magnet indicator worried me as it was permanently on, but found a solution for that.
In GovII screen, I had issues trying to get the min set, eventually realised I had to engage Thr Cut.
Thought I had everything right and drove to my field to test.
Blades Off, Computer setup and connected to VBar etc, Tx switch to Idle. Started engine and it does not 'idle' it is spooling up, i have not clicked to 'run' yet, no Idleups engaged either
Tried this a couple of times and the engine would not idle no matter what I did.
Looked at the videos again and they are talking about 'banks' and spoolups.
In GovII page there is a 'direct throttle', Selected 'Bank1' went everywhere to see if I could change anything relevant to Bank1. Nothing. Went back to 'Direct Throttle' set it back to disabled.
Went to start the heli again and it would not start. On checking throttle / servo action, the servo moved with my collective stick, did not do that before and by raising the collective I could get the engine to start and then 'idle' correctly.
Looks like a default setting was not set in the software or firmware.
Is there any concrete settings which work for Futaba, primarily a 14SG
And how do you set a max headspeed please? I was able to run the engine beyond 2200 rpm, briefly!
My big issue and from what i have read from others is that everything relates to an old software/firmware.
Screen shots show settings from some other config program which has no bearing on the version I am running. Where is the documentation for the new software/firmware please?
Would appreciate a updated 'How-To' for Nitro governors, please.
I appreciate it is more geared to VControl / Touch but I do not want to 'afford' a new transmitter as there is nothing wrong with mine.
TIA, Paul
I bought a Neo as I need the rescue feature.
Registered and upgraded everything and paid more money.
Removed the Spartan VX1n and did a step by step install into my 700n.
I used these settings to set up the 14SG T8 Setup even though its for a T8, 99% of it works. I have watched the videos from Mr Mel, read everything I can find, but i cannot get the governor to work properly.
Also the magnet indicator worried me as it was permanently on, but found a solution for that.
In GovII screen, I had issues trying to get the min set, eventually realised I had to engage Thr Cut.
Thought I had everything right and drove to my field to test.
Blades Off, Computer setup and connected to VBar etc, Tx switch to Idle. Started engine and it does not 'idle' it is spooling up, i have not clicked to 'run' yet, no Idleups engaged either
Tried this a couple of times and the engine would not idle no matter what I did.
Looked at the videos again and they are talking about 'banks' and spoolups.
In GovII page there is a 'direct throttle', Selected 'Bank1' went everywhere to see if I could change anything relevant to Bank1. Nothing. Went back to 'Direct Throttle' set it back to disabled.
Went to start the heli again and it would not start. On checking throttle / servo action, the servo moved with my collective stick, did not do that before and by raising the collective I could get the engine to start and then 'idle' correctly.
Looks like a default setting was not set in the software or firmware.
Is there any concrete settings which work for Futaba, primarily a 14SG
And how do you set a max headspeed please? I was able to run the engine beyond 2200 rpm, briefly!
My big issue and from what i have read from others is that everything relates to an old software/firmware.
Screen shots show settings from some other config program which has no bearing on the version I am running. Where is the documentation for the new software/firmware please?
Would appreciate a updated 'How-To' for Nitro governors, please.
I appreciate it is more geared to VControl / Touch but I do not want to 'afford' a new transmitter as there is nothing wrong with mine.
TIA, Paul