← VBar NEO for external transmitters

vbar neo and tail gain on 14sg translated

VBar › VBar NEO for external transmitters · Started by ReadyToFly on 3 July 2018 00:2903.07.2018 00:29
ReadyToFly 3 July 2018 00:2903.07.2018 00:29
Hello,

On the software I have:

-"gain on aux2" checked;
- aux2 -> channel 9.

On the tx I have gain on channel 9.

Even with a gain value of 0% on the tx I still get 64% on the software. Tried to lower the channel 9 end points on the tx, but the gain won't go below 64 on the PC.

What is the trick, please?

Thanks.



1 mal bearbeitet. Zuletzt am 03.07.2018 00:30 von ReadyToFly.
RV 3 July 2018 06:3203.07.2018 06:32
The trick is - and should be known in RC-Heli world by the TX manual of such radios - the split channel function for old gyros to access their AVCS / Normal mode and gain with one channel. This was done due being lack of channels about 20 years ago by Futaba …

If you can set the "Gain" channel in TX form AVCS to normal - or turn this function off - you might acces the other half / have it as full channel.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




1 mal bearbeitet. Zuletzt am 03.07.2018 06:32 von RV.
Eddi E. aus G. 3 July 2018 08:0803.07.2018 08:08
Hi,

does the value ever change, or does it stay at 64 no matter what you do?
If the latter, maybe the channel is not the proper one in the first place.
Does the control bar move, in Setup, if you change the input on your radio?

Kind regards

Eddi

Born to fly ...
forced to work.
ReadyToFly 3 July 2018 11:5203.07.2018 11:52
Hi,
The value changes on the software (the bar moves), but never goes below 64%, even when I have 0% on the tx.
Messing with the gyro end points on the tx won't change a thing.
I have been using this radio with many neos and never saw this before. Not at this magnitude.

Thanks.
Eddi E. aus G. 3 July 2018 12:0703.07.2018 12:07
Hi again,

if you check the servo monitor, what do you see (in your radio)?

The channel usually has – 100...0... +100, but if AVCS is selected for the tail gyro, not standard, the channel could be split/limited (a feature required for legacy GY gyros ...).

I take it you have model memories for each model? If so, this one could be different from the other ones.

When I was flying Futaba, I had only one model memory and bound all the receivers to the same one, and did make setup adjustments (including head speeds) only in the VBars—maybe I was anticipating VBar Control then already, even though I did not even exist ...

Kind regards

Eddi

Born to fly ...
forced to work.
ReadyToFly 3 July 2018 18:3703.07.2018 18:37
Hi,
Must I set the gain on the radio under AVCS or can it be done under non-AVCS?
Thanks.
RV 3 July 2018 19:4603.07.2018 19:46
Quote:Must I set the gain on the radio under AVCS or can it be done under non-AVCS?

Quote:The trick is - and should be known in RC-Heli world by the TX manual of such radios - the split channel function for old gyros to access their AVCS / Normal mode and gain with one channel. This was done due being lack of channels about 20 years ago by Futaba …

If you can set the "Gain" channel in TX form AVCS to normal - or turn this function off - you might acces the other half / have it as full channel.


At all … the Mode in TX doesn't care the VBar - but might be changed to access the values below 64 or above. So - set the mode you need to get the right number range in our PC display as VBar Value.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.




2 mal bearbeitet. Zuletzt am 03.07.2018 19:55 von RV.
VStabi VStabi Pioneer of Flybarless