Mark Norris
16 October 2018 23:4716.10.2018 23:47
Hello,
Can anyone who is using the VBAR NEO with a gas or nitro helicopter comment on the procedure they use to get flying at the field. I will describe how I'm currently operating my heli and would appreciate any comments or suggestions.
Currently I have direct throttle control on bank 1 / band 2,3 are governed with 1700 and 1900 head speed respectively.
Keeping it real simple:
First- I start my helicopter in bank 1 and manually spool the engine up to a reasonable RPM (less than mid stick).
Second- I switch to bank 2 and let the helicopter spool up to 1700rpm.
Third- Take off and fly around.
Fourth- Land the helicopter.
Fifth- When just below mid stick switch back to bank 1 and bring the throttle down manually.
Does this sound reasonable, my only issue is spooling up and spooling down seem to be a bit hair raising.
Thanks for any comments.
Mark Norris
RV
17 October 2018 06:3517.10.2018 06:35
First - i would set up basic throttle and collective dd in Bank1 to get approx. same HS in zero and hover as Bank2 ;-)
Lower basic unless the HS matches for zero, then dial the ad as it sounds "similar" in a hover. So you can switch in hover now ;-)
But - i personally spool it up like a electric, just all 3 banks governed, ramp limit is set to "2", collective on center and flip the switch ...
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
1 mal bearbeitet. Zuletzt am 17.10.2018 06:35 von RV.
Mark Norris
17 October 2018 15:5417.10.2018 15:54
Hello Rainer,
Thank you for your response. I have a question regarding the basic throttle and collective you mention.
If I change my collective in my transmitter it directly affects the throttle. If I change my throttle it has no effect. Can you please elaborate on how I can make changes to the throttle and collective in bank 1. I should mention I'm not using Vcontrol I'm using a Spektrum DX8G2.
I'm moving towards spooling up like an electric but I'm not quite there yet.
Thank you
Mark Norris
RV
17 October 2018 16:1517.10.2018 16:15
Oh well ... 3rd party radio ...
Did you set up the TX full according our spec like:
- Motor Channel representing Off (Idle) - Auto (AR, will be possible to be switched after Run was there, AR from ground makes no sense) - Run (Flight)
- Kill channel representing On - Off
- Bank Switch representing 3 Banks
And NO interactions between those?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mark Norris
17 October 2018 17:5417.10.2018 17:54
Hello Rainer,
Yes I have setup the radio according to your spec. (kill switch) - (off / idle / run switch) - (bank switch) - (rescue switch). No unexpected interactions.
Exactly like the below link.
https://www.vstabi.info/en/node/1990
Were you previously saying I could change "Basic Throttle" or "Collective Add" in Bank 1 on PC software to improve my results?
AR Idle
Runup Speed
Basic Throttle
Minimum Throttle
Collective Add
Collective Dynamic
Cyclic Add
Integral
P Limit +
Differential
Idle
The only "hiccup" I have is when flipping from bank 2 back to bank 1 with manual throttle the engine
increases rpm at mid stick.
Mark
8 mal bearbeitet. Zuletzt am 17.10.2018 23:09 von Mark Norris.
RV
18 October 2018 06:3118.10.2018 06:31
https://www.vstabi.info/en/node/2030
OK - then lower the basic throttle in bank1 a bit. Probably might afterwards check the collective ad there too (switching from 2 to 1 in a hover)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mark Norris
20 October 2018 02:3520.10.2018 02:35
Hi Rainer,
I've lowered the Basic Throttle in Bank 1 from 50 to 40 and that indeed lowers the throttle at hover, perfect. Another question I have is will it be possible to have a slightly reduced negative collective range when in Bank 1 without affecting the current throttle curve in Bank 1.
I appreciate all your help.
Thanks
Mark Norris
RV
20 October 2018 09:5820.10.2018 09:58
So - you don't want to have a "symmetrical" v-shaped throttle curve in Bank1?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Mark Norris
21 October 2018 01:1921.10.2018 01:19
Hello Rainer,
Bank 1 throttle curve is currently OK. Can you please explain in detail how collective ad should be used.
Thank you
RV
21 October 2018 11:3821.10.2018 11:38
Here we go - Step 1:
https://www.vstabi.info/en/node/2043
Or in the previously posted link - scroll to the bottom ;-)
https://www.vstabi.info/en/node/2030
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.