← VBar NEO for external transmitters

Rescue set up with Spektrum tx translated

VBar › VBar NEO for external transmitters · Started by phili_o_fish on 10 July 2018 16:4610.07.2018 16:46
phili_o_fish 10 July 2018 16:4610.07.2018 16:46
Hi,

I have a Spektrum DX7, 7 channel transmitter and would like to purchase pro with rescue for my neo.

I'm running an esc which works with just throttle curves and use gyro channel for bank switching.

Can I assign aux2 to the rescue in the neo?

Thanks in advance for your help. I can only see aux3 options on the videos I've seen but hoping this is possible until I can save for a vbar controller.

Phil
Eddi E. aus G. 11 July 2018 09:3711.07.2018 09:37
Hi Phil,

just enter the desired channel number from your radio, for each function.

So this would be Ail/Ele/Tail/Pitch to the corresponding functions of the VBar, Thro to AUX3 (to run the ESC with the throttle curves from the radio, if you want that, ESC then connected to the AUX3 port), and your two additional channels to Bank and Rescue, and that's that.

Kind regards

Eddi

Born to fly ...
forced to work.
hbar500 5 November 2018 02:1105.11.2018 02:11
Hello Eddi

I made this configuration on my DX8 G2 but it does not work for me, the ESC Talon 90 does not arm itself. I would like to use the configuration of the old Vbar where the acceleration curves were programmed in the ESC and flat curves were used in the Tx. On the other hand I do not manage to configure the mode of rescue, would be so kind to guide me in the forum where I can get that information? It's frustrating and I do not understand why Mikado does not publish a detailed tutorial on the configuration with radios of different brands. The information on the VStabi page is not enough for those of us who have a low or medium level in the hobby. Thank you very much for the help you can give me.


Best regard

Harold
Eddi E. aus G. 5 November 2018 09:3805.11.2018 09:38
Hi Harold,

well, with a different brand radio, there are many variables. Take Spektrum and all the different radios of different ages with different versions of their software, for example.

But the basic principles:

If you do the AUX3-thing, connect a servo to the AUX3 port, as a pointer, even in parallel with the ESC, using a Y-harness.
This way you can see what happens on the physical port.
If you set a throttle curve from 0...100 % throttle (or –100...+100 % channel), you have the full throttle travel, to program the ESC (using the means of the ESC, stick programming, beeps, done).
Then, you would program your radio in a way that autorotation/motor off outputs 0 % throttle (or –100 % channel), in this configuration, the ESC will arm.
And you would program your radio (flight modes/conditions) in a way so you have flat curves (like 60, 75, 90 % of throttle across the board), and let the ESC do it's thing, with it's internal governor.

It's the same on all radios, just the tools (programming interface) on your tx are different, but they should be documented properly by the manufacturer of the respective radio.

Regarding Rescue, in the VBar, it has three states (Beginner/Hovering (self-leveling), Off (normal flight) and Rescue (...)).
So you just need to assign a channel with three position switch (at best a quick-break switch, which jumps back to Off after actuating/triggering Rescue, to arm it again), and select what you want (Rescue and Beginner (three positions required) or only Rescue (two positions required, center (Off) and Full (Rescue), for example.
If you intend to use a push button or two position switch, mind to adjust the travel so, in the VBar Software, you switch between Off (normal flight) and Rescue (...). If you would omit the center position and switch between Beginner and Rescue (Beginner selected or not), Rescue might not arm after the first actuation, because the center position will never be transmitted to the VBar ... and it can only react to what you tell it ;-)

Hope this helps.

Kind regards

Eddi

Born to fly ...
forced to work.
VStabi VStabi Pioneer of Flybarless