← VBar NEO for external transmitters

How to go to bailout autoratation in vbar neo express? translated

VBar › VBar NEO for external transmitters · Started by 666yeti666 on 23 March 2019 23:0523.03.2019 23:05
666yeti666 23 March 2019 23:0523.03.2019 23:05
Good evening,
I'm currently building up my new logo700 and using a vbar neo express.
From previous versions (5.3 pro) I was used to see a separate box for autoratation bailout mode and also on the mainscreen you could see when bailout was armed. Used this for many years, but now obviously that does not exist anymore or is it not present in express ?

On the other hand, when I decrease the throttle channel value gradually (in transmitter) I do see something called "motor idle" in the "receiver and transmitter" set-up tab.
Is this the bailout mode ? I did a test by switching from "motor on" to this "motor idle", with a 30% throttle setting (in the transmitter) but then the motor stopped rotating. Then when switching back to "motor on" again the motor spooled up slowly.

So my questions are:
1) is "motor idle" the same as bail-out ?
2) if yes, why does my motor stop rotating and why I do not have a fast motor spool-up ?
3) what am I doing wrong ?
4) if bailout not present in express, is it present in the neo pro version ?

thanks
regards
Sebastien
RV 24 March 2019 10:5024.03.2019 10:50
1) is "motor idle" the same as bail-out ?

Yes


2) if yes, why does my motor stop rotating and why I do not have a fast motor spool-up ?

which ESC? - which Governor? - is the Motor input channel on the pc working in the 3 values as requested? - was the motor turned on once before?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
666yeti666 24 March 2019 22:2224.03.2019 22:22
Hi Rainer,
-which ESC? => Jeti Mezon 130
-which Governor? => vbar ! external hobbywing sensor going to the "RPM" input of the vbar neo
-is the Motor input channel on the pc working in the 3 values as requested? => yes, I can see it appearing in the "receiver/transmitter" tab : motor stop, motor idle, motor run
-was the motor turned on once before? => yes, on the bench only. Now that I think of it, with previous versions of vbar governor, the motor has to run for at least about 15 seconds, before bail-out is possibe .... :-(

I also noticed that the rpm wouldn't go lower than about 1600rpm. I assume this is caused by maingear ratio of 9.71 (pinion =14T) and maybe v-bar does "block" this due to that not all ESC's can run at very low RPM's ? I would like to go down to 1300rpm (JEti MEzon can handle this very well). Is this possible with the vbar or do I need pro version for this (a smaller pinion would also be possible but I also like to run max 2000rpm).

Another thing : If I check the log file I also see the following message : "Sattelite data out of synchronization"
I use Jeti 2.4 GHz sattelite Rsat2 with UDI 12. Settings are : output period=20ms, PPM-UDI mode: computed
I understood that this is the correct setting ? Why the messages ?

I included the vbar file.

thanks a lot !
kind regards
Sebastien
RV 25 March 2019 06:1325.03.2019 06:13
Could you have a look at the throttle bar in pc software (run the heli w/o blades) - does it be a little bit open when you toggle from run to Idle?


RPM - with blades or not? - on the bench w/o load this could appear. if with blades - consider to have the right gear for your HS. Too less load on the ESC gives always heat - even on a "good one". But - if liked - you can adjust a Min Limit Parameter with Pro which is the lowest throttle position for the Governor.


Jeti - when this messages appear - check all electronic components. If they appear with running motor, check Motor and ESC for insulation errors and belt drives for discharges. Check connection cable to NEO. If they appear only once right at powerup it is normal (data has to be synchronized first). If it is in between flight and all above ok - contact Jeti.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
666yeti666 14 April 2019 13:0514.04.2019 13:05
RV schrieb:
-------------------------------------------------------
> Could you have a look at the throttle bar in pc
> software (run the heli w/o blades) - does it be a
> little bit open when you toggle from run to Idle?
=> Finally find the time to do more checks. I have checked the throttle bar and indeed it's still a bit open, the bar is a little bit blue. I have increased the throttle channel on the bench without blades while in bail-out mode but noting happens , the motor doesn't run. When I increase it more and more of course the throttle bar will go to run and the motor starts running.
I have attached the logging + setup file, maybe this gives you more information ?


>
> RPM - with blades or not? - on the bench w/o load
> this could appear. if with blades - consider to
> have the right gear for your HS. Too less load on
> the ESC gives always heat - even on a "good one".
> But - if liked - you can adjust a Min Limit
> Parameter with Pro which is the lowest throttle
> position for the Governor.
=> problem is solved, I bought a smaller pinion (13T) and now I can go easily to 1000rpm

>
> Jeti - when this messages appear - check all
> electronic components. If they appear with running
> motor, check Motor and ESC for insulation errors
> and belt drives for discharges. Check connection
> cable to NEO. If they appear only once right at
> powerup it is normal (data has to be synchronized
> first). If it is in between flight and all above
> ok - contact Jeti.
=> I've checked the logging and indeed it only happens just after connecting the battery, so no issue.

thanks again!
regards
Seb Dateianhänge:
öffnen | Download - Logo 700 log + settings 14-4-2019.zip (2.2 KB)
666yeti666 18 April 2019 16:0318.04.2019 16:03
Hello Rainer, I hope you have some time to look into this and give some suggestions :

RV schrieb:
-------------------------------------------------------
> Could you have a look at the throttle bar in pc
> software (run the heli w/o blades) - does it be a
> little bit open when you toggle from run to Idle?

=> Finally find the time to do more checks. I have checked the throttle bar and indeed it's still a bit open, the bar is a little bit blue. I have increased the throttle channel on the bench without blades while in bail-out mode but noting happens , the motor doesn't run. When I increase it more and more of course the throttle bar will go to run and the motor starts running.
I have attached the logging + setup file, maybe this gives you more information ?

thanks in advance
Seb
RV 18 April 2019 21:4118.04.2019 21:41
At the flight panels in PC - Governor - Experts - the first value … might be your friend ;-)

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
666yeti666 20 April 2019 09:0820.04.2019 09:08
Hi Rainer,
ok danke, leider heb ich die Express version.
Gibt's noch eine andere moglichkeit ... ?
Frohe Ostern !

mfg
Seb
RV 20 April 2019 11:3120.04.2019 11:31
Leider nein, der Gaswert ist da fest vorgegeben. Normalerweise passt das aber mit den Reglern, ich prüfe das mal mit einem YGE nach.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
666yeti666 21 April 2019 13:2121.04.2019 13:21
Oh das ist schade, ubrigens verwende ich ein jeti Mezon 130.
Gibts vieleicht "low level programming" zur anderung der gaswert...?
Mfg
Sébastien
666yeti666 24 April 2019 13:1524.04.2019 13:15
Hallo Rainer
Hattest du das noch nachprufen konnen mit dem yge regler?
Mfg
Seb
RV 24 April 2019 21:3024.04.2019 21:30
Okay - i did here with a Express NEO and the VBC-t (which doesn't care) YGE65LVT and a Scorpion Motor.

It kept it running at a very low speed (10% throttle output is given) as intended.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
666yeti666 25 April 2019 22:5325.04.2019 22:53
OK, thank you for trying! . Maybe I could re-learn the limits for the throttle channel?
Or go over to the pro version (or wouldn't it work also not... Mmm... )
Regards
Seb
RV 26 April 2019 06:2726.04.2019 06:27
You can try the following method:

- set "Motor off" to 50% (Motor may turn!)
- Power cycle Model
- tweak "Motor off" now unless ESC arms

SO now you have set u p what the ESC needs as minimum for "off". Then try.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
666yeti666 1 May 2019 21:4901.05.2019 21:49
Hello Rainer,
I bought the pro version just for convenience and now the bail-out does work does work, it revealed that I only had to go to a vaue of 15 in order to keep the motor spinning. So my esc was on the edge of what was recognized as a valid minimum throttle signal.
After updating to the pro version I got a new problem but will make a new item in the forum.

regards
Sebastien
VStabi VStabi Pioneer of Flybarless