p1andy
22 May 2019 20:1922.05.2019 20:19
Hello All,
I have an issue with a Vbar NEO of mine installed in a Logo 550. It was flying fine up until recently when it failed to initialize with warning sounds and flashing red. I have read up about tapping the NEO and reverting it back to pro software none of which have cured the problem. The only thing this has done is broken the tabs on the case of the NEO :-(
Does any one have any suggestions on how to get it working again?
RV
22 May 2019 23:0422.05.2019 23:04
Could you please add the full log with all entries here?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
p1andy
23 May 2019 08:4023.05.2019 08:40
Sorry but there is not much to see on the logs as it does not boot up, but please see below sample log.
VBar Start -- LOGO 550 -- 15.05.2019 -- 18:41:58
18:41:58;1;Reset Reason: Power On
18:42:00;2;Bank 2 Loaded
18:42:00;1;Motorswitch Motor Off
18:42:00;1;Motorswitch Idle Bailout
18:42:03;2;Calibration Finished
18:42:03;3;IMU Sensor delivers no data
18:42:03;4;IMU Stopped delivering Data
18:42:04;4;IMU Stopped delivering Data
18:42:04;4;IMU Stopped delivering Data
18:42:04;4;IMU Stopped delivering Data
18:42:05;4;IMU Stopped delivering Data
18:42:05;4;IMU Stopped delivering Data
18:42:05;4;IMU Stopped delivering Data
18:42:05;4;IMU Stopped delivering Data
18:42:06;4;IMU Stopped delivering Data
18:42:06;4;IMU Stopped delivering Data
18:42:06;4;IMU Stopped delivering Data
18:42:06;4;IMU Stopped delivering Data
18:42:07;4;IMU Stopped delivering Data
18:42:07;4;IMU Stopped delivering Data
18:42:07;4;IMU Stopped delivering Data
18:42:09;4;IMU Stopped delivering Data
18:42:09;4;IMU Stopped delivering Data
18:42:09;4;IMU Stopped delivering Data
18:42:09;4;IMU Stopped delivering Data
18:42:10;4;IMU Stopped delivering Data
18:42:10;4;IMU Stopped delivering Data
18:42:10;4;IMU Stopped delivering Data
18:42:10;4;IMU Stopped delivering Data
18:42:11;4;IMU Stopped delivering Data
18:42:11;4;IMU Stopped delivering Data
VBar Logfile End -- 15.05.2019 -- 18:42:13
Eddi E. aus G.
23 May 2019 12:4323.05.2019 12:43
Hi,
it's about the exact wording, and how often this occurs.
Power supply is OK, I assume? Is it different with a regular receiver battery, compared to a BEC or other regulator, if you are using one of these?
If the issue persists, I'm afraid we should check the unit at our service shop.
To create a service request, please go www.vstabi.info/devices and click Service, for the serial no. in question.
Kind regards
Eddi
Born to fly ...
forced to work.
p1andy
23 May 2019 18:0523.05.2019 18:05
It is always run through a BEC so i have just checked it with a 2s lipo direct and it is still showing the same errors. Looks like it will have to be sent in :-(
p1andy
23 May 2019 18:1923.05.2019 18:19
I have filled out the service request, what do i do now? Do i await contact or do i send the NEO in for inspection?