Hi
After changing from YGE to Tribunus 06-80 ESC for my Goblin 380, I had two successfull flights with no errors.
On the third flight, the ESC would not arm.
The motor keeps beeping one long and one short morse-code. It also randomly spins 1/4 turn and stops again.
I'm not 100% sure if the ESC is faulty, as I'm getting error messages in the vbar log.
I'm getting:
-Warmstart
-IMU does not deliver any data anymore
-Error;Aileron Sensor Value out of Range
-Warn;Scorpion Input Signal
-Warn;Init Failed, retrying...
This is the log from the second flight:
03.07.2019 20:25:20;VStabi Start -- Goblin 380
03.07.2019 20:25:22 Good;Scorpion ESC detected
03.07.2019 20:25:22 Warn;Scorpion Input Signal
03.07.2019 20:25:22 Good;Reset Reason: Power On
03.07.2019 20:25:22 Info;Bank 3 Loaded
03.07.2019 20:25:25 Info;Calibration Finished
03.07.2019 20:25:27 Good;/battery/bt_2
03.07.2019 20:25:27 Good;Battery selected manually: Pulse 1800 mAh #1
03.07.2019 20:26:46 Info;Bank 2 Loaded
03.07.2019 20:26:47 Info;Bank 1 Loaded
03.07.2019 20:26:49 Info;Bank 2 Loaded
03.07.2019 20:26:51 Info;Bank 3 Loaded
03.07.2019 20:26:51 Info;Bank 1 Loaded
03.07.2019 20:26:52 Info;Bank 2 Loaded
03.07.2019 20:26:54 Info;Bank 1 Loaded
03.07.2019 20:26:55 Info;Bank 2 Loaded
03.07.2019 20:27:24 Info;Governor Active
03.07.2019 20:27:24 Good;Motorswitch Motor On
03.07.2019 20:27:37 Info;Bank 3 Loaded
03.07.2019 20:27:47 Info;Raised Vibration Level
03.07.2019 20:27:52 Info;Bank 2 Loaded
03.07.2019 20:27:59 Info;Governor Idle
03.07.2019 20:28:00 Good;Motorswitch Idle Bailout
03.07.2019 20:28:01 Info;ESC - Umin:20.9V Imax:49.5A Temp:28?
03.07.2019 20:28:01 Info;Governor Stop
03.07.2019 20:28:01 Good;Motorswitch Motor Off
03.07.2019 20:28:07 Info;Raised Vibration Level
03.07.2019 20:28:20 Info;Governor Active
03.07.2019 20:28:21 Good;Motorswitch Motor On
03.07.2019 20:28:27 Warn;High Vibration Level
03.07.2019 20:28:30 Info;Bank 3 Loaded
03.07.2019 20:28:37 Info;Raised Vibration Level
03.07.2019 20:28:47 Warn;High Vibration Level
03.07.2019 20:28:57 Info;Raised Vibration Level
03.07.2019 20:29:08 Info;Raised Vibration Level
03.07.2019 20:29:16 Error;Aileron Sensor Value out of Range
03.07.2019 20:29:28 Info;Raised Vibration Level
03.07.2019 20:29:48 Info;Raised Vibration Level
03.07.2019 20:29:50 Info;Bank 2 Loaded
03.07.2019 20:30:08 Info;Raised Vibration Level
03.07.2019 20:30:29 Info;Raised Vibration Level
03.07.2019 20:30:39 Info;Raised Vibration Level
03.07.2019 20:30:41 Info;Bank 3 Loaded
03.07.2019 20:30:49 Info;Raised Vibration Level
03.07.2019 20:31:10 Info;Bank 2 Loaded
03.07.2019 20:31:19 Info;Governor Idle
03.07.2019 20:31:20 Good;Motorswitch Idle Bailout
03.07.2019 20:31:29 Error;Extreme Vibration Level
03.07.2019 20:31:30 Info;Governor Stop
03.07.2019 20:31:30 Good;Motorswitch Motor Off
03.07.2019 20:31:32 Info;ESC - Umin:20.6V Imax:51.9A Temp:40?
03.07.2019 20:32:19 Info;Bank 1 Loaded
03.07.2019 20:32:22 Info;Bank 2 Loaded
03.07.2019 20:32:23 Info;Bank 3 Loaded
03.07.2019 20:32:24 Info;Bank 2 Loaded
03.07.2019 20:32:24 Info;Bank 1 Loaded
03.07.2019 20:33:42;VBar Logfile End -- 03.07.2019 -- 20:33:42
And here is the log from next attempt to fly:
03.07.2019 21:30:00;VStabi Start -- Goblin 380
03.07.2019 21:30:01 Good;Reset Reason: Power On
03.07.2019 21:30:01 Good;Scorpion ESC detected
03.07.2019 21:30:01 Warn;Scorpion Input Signal
03.07.2019 21:30:02 Info;Bank 3 Loaded
03.07.2019 21:30:02 Warn;Init Failed, retrying...
03.07.2019 21:30:03 Warn;Init Failed, retrying...
03.07.2019 21:30:05 Good;/battery/bt_2
03.07.2019 21:30:05 Good;Battery selected manually: Pulse 1800 mAh #1
03.07.2019 21:30:10 Info;Calibration Finished
03.07.2019 21:31:19;VBar Logfile End -- 03.07.2019 -- 21:31:19
Today, at first attemt, the ESC armed on the bench.. But on second attempt I got folowing error and the ESC did not arm.
22.07.2019 07:27:47;VStabi Start -- Goblin 380
22.07.2019 07:27:48 Warn;Reset Reason: Watchdog
22.07.2019 07:27:52 Info;Calibration Finished
22.07.2019 07:29:45 Error;Warmstart
22.07.2019 07:29:46 Good;Reset Reason: Power On
22.07.2019 07:29:46 Error;IMU Stopped delivering Data
22.07.2019 07:33:04;VBar Logfile End -- 22.07.2019 -- 07:33:04
Inbetween the error codes, I get "Good Health message (10 sec)
Do you think this is related to error in the ESC or the Vbar NEO itselfe?
Best regards
Tormod Ihlen
After changing from YGE to Tribunus 06-80 ESC for my Goblin 380, I had two successfull flights with no errors.
On the third flight, the ESC would not arm.
The motor keeps beeping one long and one short morse-code. It also randomly spins 1/4 turn and stops again.
I'm not 100% sure if the ESC is faulty, as I'm getting error messages in the vbar log.
I'm getting:
-Warmstart
-IMU does not deliver any data anymore
-Error;Aileron Sensor Value out of Range
-Warn;Scorpion Input Signal
-Warn;Init Failed, retrying...
This is the log from the second flight:
03.07.2019 20:25:20;VStabi Start -- Goblin 380
03.07.2019 20:25:22 Good;Scorpion ESC detected
03.07.2019 20:25:22 Warn;Scorpion Input Signal
03.07.2019 20:25:22 Good;Reset Reason: Power On
03.07.2019 20:25:22 Info;Bank 3 Loaded
03.07.2019 20:25:25 Info;Calibration Finished
03.07.2019 20:25:27 Good;/battery/bt_2
03.07.2019 20:25:27 Good;Battery selected manually: Pulse 1800 mAh #1
03.07.2019 20:26:46 Info;Bank 2 Loaded
03.07.2019 20:26:47 Info;Bank 1 Loaded
03.07.2019 20:26:49 Info;Bank 2 Loaded
03.07.2019 20:26:51 Info;Bank 3 Loaded
03.07.2019 20:26:51 Info;Bank 1 Loaded
03.07.2019 20:26:52 Info;Bank 2 Loaded
03.07.2019 20:26:54 Info;Bank 1 Loaded
03.07.2019 20:26:55 Info;Bank 2 Loaded
03.07.2019 20:27:24 Info;Governor Active
03.07.2019 20:27:24 Good;Motorswitch Motor On
03.07.2019 20:27:37 Info;Bank 3 Loaded
03.07.2019 20:27:47 Info;Raised Vibration Level
03.07.2019 20:27:52 Info;Bank 2 Loaded
03.07.2019 20:27:59 Info;Governor Idle
03.07.2019 20:28:00 Good;Motorswitch Idle Bailout
03.07.2019 20:28:01 Info;ESC - Umin:20.9V Imax:49.5A Temp:28?
03.07.2019 20:28:01 Info;Governor Stop
03.07.2019 20:28:01 Good;Motorswitch Motor Off
03.07.2019 20:28:07 Info;Raised Vibration Level
03.07.2019 20:28:20 Info;Governor Active
03.07.2019 20:28:21 Good;Motorswitch Motor On
03.07.2019 20:28:27 Warn;High Vibration Level
03.07.2019 20:28:30 Info;Bank 3 Loaded
03.07.2019 20:28:37 Info;Raised Vibration Level
03.07.2019 20:28:47 Warn;High Vibration Level
03.07.2019 20:28:57 Info;Raised Vibration Level
03.07.2019 20:29:08 Info;Raised Vibration Level
03.07.2019 20:29:16 Error;Aileron Sensor Value out of Range
03.07.2019 20:29:28 Info;Raised Vibration Level
03.07.2019 20:29:48 Info;Raised Vibration Level
03.07.2019 20:29:50 Info;Bank 2 Loaded
03.07.2019 20:30:08 Info;Raised Vibration Level
03.07.2019 20:30:29 Info;Raised Vibration Level
03.07.2019 20:30:39 Info;Raised Vibration Level
03.07.2019 20:30:41 Info;Bank 3 Loaded
03.07.2019 20:30:49 Info;Raised Vibration Level
03.07.2019 20:31:10 Info;Bank 2 Loaded
03.07.2019 20:31:19 Info;Governor Idle
03.07.2019 20:31:20 Good;Motorswitch Idle Bailout
03.07.2019 20:31:29 Error;Extreme Vibration Level
03.07.2019 20:31:30 Info;Governor Stop
03.07.2019 20:31:30 Good;Motorswitch Motor Off
03.07.2019 20:31:32 Info;ESC - Umin:20.6V Imax:51.9A Temp:40?
03.07.2019 20:32:19 Info;Bank 1 Loaded
03.07.2019 20:32:22 Info;Bank 2 Loaded
03.07.2019 20:32:23 Info;Bank 3 Loaded
03.07.2019 20:32:24 Info;Bank 2 Loaded
03.07.2019 20:32:24 Info;Bank 1 Loaded
03.07.2019 20:33:42;VBar Logfile End -- 03.07.2019 -- 20:33:42
And here is the log from next attempt to fly:
03.07.2019 21:30:00;VStabi Start -- Goblin 380
03.07.2019 21:30:01 Good;Reset Reason: Power On
03.07.2019 21:30:01 Good;Scorpion ESC detected
03.07.2019 21:30:01 Warn;Scorpion Input Signal
03.07.2019 21:30:02 Info;Bank 3 Loaded
03.07.2019 21:30:02 Warn;Init Failed, retrying...
03.07.2019 21:30:03 Warn;Init Failed, retrying...
03.07.2019 21:30:05 Good;/battery/bt_2
03.07.2019 21:30:05 Good;Battery selected manually: Pulse 1800 mAh #1
03.07.2019 21:30:10 Info;Calibration Finished
03.07.2019 21:31:19;VBar Logfile End -- 03.07.2019 -- 21:31:19
Today, at first attemt, the ESC armed on the bench.. But on second attempt I got folowing error and the ESC did not arm.
22.07.2019 07:27:47;VStabi Start -- Goblin 380
22.07.2019 07:27:48 Warn;Reset Reason: Watchdog
22.07.2019 07:27:52 Info;Calibration Finished
22.07.2019 07:29:45 Error;Warmstart
22.07.2019 07:29:46 Good;Reset Reason: Power On
22.07.2019 07:29:46 Error;IMU Stopped delivering Data
22.07.2019 07:33:04;VBar Logfile End -- 22.07.2019 -- 07:33:04
Inbetween the error codes, I get "Good Health message (10 sec)
Do you think this is related to error in the ESC or the Vbar NEO itselfe?
Best regards
Tormod Ihlen