← VBar NEO for external transmitters

Problems configuring VBar Neo with Spektrum TX translated

VBar › VBar NEO for external transmitters · Started by Arag_ on 6 August 2019 12:2106.08.2019 12:21
Arag_ 6 August 2019 12:2106.08.2019 12:21
Hello,

I am trying to configure the following setup for a G420 heli:
TX: Spektrum DX18 Gen 2
FBL: VBar Neo non Vlink
RX: 2 DSMX spektrum satellites
ESC: Kontronik Koby 90LV

I plan to use the external governor of the Koby ESC.

The problems I have encountered are the following ones:

1.- I don't understand the differences connecting the ESC to the ESC port or to Aux 2 port on the Neo. Currently I have it connected to the ESC port of the Neo.
2.- As I am going to use the ESC external governor I understand there is no need to use the Gov II tab in the setup, right?
3.- Usually I use different throttle curves in the TX for each flight mode (assigned to bank switch). I guess that is right.
4.- Should I use another switch in the TX to assign the motor channel (Off, Idle, Run)? Which channel should be assign that switch?
5.- To program the Koby ESC I used the Kontronik ProgUnit configuring through the K-Config software using the usb and the PC, so I don't need to program the ESC through beeps. I have reed in another post on the forum the following sentence: "If you set a throttle curve from 0...100 % throttle (or –100...+100 % channel), you have the full throttle travel, to program the ESC (using the means of the ESC, stick programming, beeps, done).". I am a bit messed about how to configure TCs, motor channel...
6.- Regarding Rescue mode, I have bought the Rescue and installed the firmware as you can see in the following image:

Also, I have configured in the Spektrum TX the channel Aux 3 to a 3 position switch and also to a 2 position switch, but when I change the switch I haven't see any change in the Receiver tab of the Vbar Neo program. How must be configured the rescue mode with the Spektrum TX?



2 mal bearbeitet. Zuletzt am 06.08.2019 13:44 von Arag_.
Arag_ 8 August 2019 11:1108.08.2019 11:11
Finally, I have been able to configure most of the things by myself, but I have several doubts at the moment.

Arag_ Wrote:
-------------------------------------------------------
> Hello,
>
> I am trying to configure the following setup for a
> G420 heli:
> TX: Spektrum DX18 Gen 2
> FBL: VBar Neo non Vlink
> RX: 2 DSMX spektrum satellites
> ESC: Kontronik Koby 90LV
>
> I plan to use the external governor of the Koby
> ESC.
>
> The problems I have encountered are the following
> ones:
>
> 1.- I don't understand the differences connecting
> the ESC to the ESC port or to Aux 2 port on the
> Neo. Currently I have it connected to the ESC port
> of the Neo.
Still doesn't know that difference.

> 2.- As I am going to use the ESC external governor
> I understand there is no need to use the Gov II
> tab in the setup, right?
Solved, I have found there is no need.

> 3.- Usually I use different throttle curves in the
> TX for each flight mode (assigned to bank switch).
> I guess that is right.
I have discover in the throttle curves it must be configured one for 0%, another for 50% and another one for 100%. But I am not sure if the flight mode must change with the bank switch or with the motor switch.

> 4.- Should I use another switch in the TX to
> assign the motor channel (Off, Idle, Run)? Which
> channel should be assign that switch?
Resolved, it must be used another 3 positions switch, asignned to a different channel.

> 5.- To program the Koby ESC I used the Kontronik
> ProgUnit configuring through the K-Config software
> using the usb and the PC, so I don't need to
> program the ESC through beeps. I have reed in
> another post on the forum the following sentence:
> "If you set a throttle curve from 0...100 %
> throttle (or –100...+100 % channel), you have
> the full throttle travel, to program the ESC
> (using the means of the ESC, stick programming,
> beeps, done).". I am a bit messed about how to
> configure TCs, motor channel...
Solved, I am going to use the new way to configure the Neo, with motor switch assigned to a different channel.
What I don't know is how to assign different rpm to the differents flight modes.

> 6.- Regarding Rescue mode, I have bought the
> Rescue and installed the firmware as you can see
> in the following image:
> https://lh3.googleusercontent.com/xrsTzF-n0qdZfvvM
> Ac2oNB4ejDHdNjQvG2QJ5rkfRSPDms98NVAuY1PVv_DQaqOYIe
> mL9IEm0gESXX0HA1R8Wd7WehDfz5QR1LQY5skMUqfBUsBEt6kL
> Z7CCbs3vn3BGxUX3NPW-n3SvejdjWq6a1C1yF1MdxBxE7t_8Hx
> 4m_ku8WRPXwxDwzmTDdQ4wq1QzQGrXnXGo0WRp9jMWddtsM9qz
> ot7HGg2D71YM1m09z372LCEZUfts0wK1xFfZIEMD3krx3qM1TE
> NvS_l7Ngf5LmzN9RKfScR5rqdps5cgEtk5LHFXjGR2Afbc8p-z
> PWlRhlw12KzMn6NR_uamgjn-R2pJXPdzs1GaUopQU-ofpEkt_x
> whkk0ESwKrgVwNmxuIV53lC50yYal0z5MrwtAwfrF2dcxKxewt
> BWVbCjnBeyQSandNkfvJTKQv_r5RtQMHQ7RTs0NGyd75_GmGqI
> 2B4WNHvyApuZxj6CSMDR8l3MnuQO0AZHR47GLx_ggJ8WLNXxJw
> 2-IWZpkji5as9qRXon9roHkGXvyLGmjGtVwjaikI6XkFZc5yut
> 475x5EoUyf42r1P2j62STD9TVvobn1Rqsp4ChLeTpsVcLc2stW
> YMeV-MN_lgY2A9YbbrqOPNG7lpRArHsVuIdRoz6bQh9lQjPYmb
> sTBz8L=w1301-h759-no
> Also, I have configured in the Spektrum TX the
> channel Aux 3 to a 3 position switch and also to a
> 2 position switch, but when I change the switch I
> haven't see any change in the Receiver tab of the
> Vbar Neo program. How must be configured the
> rescue mode with the Spektrum TX?
Solved, the rescue mode was assigned in the receiver tab of the neo to a different channel in the tx.



1 mal bearbeitet. Zuletzt am 08.08.2019 11:12 von Arag_.
RV 8 August 2019 16:4608.08.2019 16:46
Quote:> Hello,
>
> I am trying to configure the following setup for a
> G420 heli:
> TX: Spektrum DX18 Gen 2
> FBL: VBar Neo non Vlink
> RX: 2 DSMX spektrum satellites
> ESC: Kontronik Koby 90LV
>
> I plan to use the external governor of the Koby
> ESC.
>
> The problems I have encountered are the following
> ones:
>
> 1.- I don't understand the differences connecting
> the ESC to the ESC port or to Aux 2 port on the
> Neo. Currently I have it connected to the ESC port
> of the Neo.
Still doesn't know that difference.

AUX2 - Method from TX as for guys with 3rd party radios almost want.

ESC - VBar Method - ESC out is switched by Motor Switch State - with the values inside the NEO (as for VBC)




Quote:> 3.- Usually I use different throttle curves in the
> TX for each flight mode (assigned to bank switch).
> I guess that is right.
I have discover in the throttle curves it must be configured one for 0%, another for 50% and another one for 100%. But I am not sure if the flight mode must change with the bank switch or with the motor switch.

Using Throttle for Motor Switch State (which is mandatory needed in both cases above!) it has to be so.
Using throttle for AUX2 - use another channel to give us your motor states in the required way.


At the end - it is best to "simulate" a VBC with your "Throttle" channel in the 3 positions - and connect the ESC to ESC and set up the VBar for "external Gov" (sorry - no VGov for Kontronik…) and dial in the fixed %-Values in the Var with the PC Software each Bank and for AR.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Arag_ 9 August 2019 08:2809.08.2019 08:28
Thanks a lot Rainer, but I still doesn't know where to configure the percentage to set the different RPM in each flight mode. I guess it is in the parameters "Throttle out" and "Autorotation" and those values represent the % in the standard throttle curve?


RV Wrote:
-------------------------------------------------------
> > Hello,
> >
> > I am trying to configure the following setup for
> a
> > G420 heli:
> > TX: Spektrum DX18 Gen 2
> > FBL: VBar Neo non Vlink
> > RX: 2 DSMX spektrum satellites
> > ESC: Kontronik Koby 90LV
> >
> > I plan to use the external governor of the Koby
>
> > ESC.
> >
> > The problems I have encountered are the
> following
> > ones:
> >
> > 1.- I don't understand the differences
> connecting
> > the ESC to the ESC port or to Aux 2 port on the
>
> > Neo. Currently I have it connected to the ESC
> port
> > of the Neo.
> Still doesn't know that difference.
>
> AUX2 - Method from TX as for guys with 3rd party
> radios almost want.
>
> ESC - VBar Method - ESC out is switched by Motor
> Switch State - with the values inside the NEO (as
> for VBC)
>
>
>
>
> > 3.- Usually I use different throttle curves in
> the
> > TX for each flight mode (assigned to bank
> switch).
> > I guess that is right.
> I have discover in the throttle curves it must be
> configured one for 0%, another for 50% and another
> one for 100%. But I am not sure if the flight mode
> must change with the bank switch or with the motor
> switch.
>
> Using Throttle for Motor Switch State (which is
> mandatory needed in both cases above!) it has to
> be so.
> Using throttle for AUX2 - use another channel to
> give us your motor states in the required way.
>
>
> At the end - it is best to "simulate" a VBC with
> your "Throttle" channel in the 3 positions - and
> connect the ESC to ESC and set up the VBar for
> "external Gov" (sorry - no VGov for Kontronik…)
> and dial in the fixed %-Values in the Var with the
> PC Software each Bank and for AR.
RV 10 August 2019 16:2110.08.2019 16:21
Quote:I guess it is in the parameters "Throttle out" and "Autorotation" and those values represent the % in the standard throttle curve?

Exactly.

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Arag_ 13 August 2019 09:2513.08.2019 09:25
Find a problem with the different rpm configured in the bank switches. I didn't experienced any rpm change when changing from a bank switch to other.
I have put 75 - 80 - 85% in the throttle out for each bank, but I guess the problem should be channel asiggned to the throttle in the receiver tab. What channel should I put in here?

I have ESC connected to ESC port, and a 3-pos switch for bank switch, another 3-pos switch for motor switch (off-idle-run).
RV 13 August 2019 23:2413.08.2019 23:24
When you connect a servo to the ESC output - does this move as expected?

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Arag_ 14 August 2019 08:1614.08.2019 08:16
I didn't make this test, but yesterday in the evening I realized what is the problem. I begin to change the throttle out value (75-80-85) to a lower value and the rpm of the motor changes. I suddenly realized I forgot to program endpoints in the ESC and that should be the problem.

I haven't enough time to program but I am pretty sure that is the cause of the problem.

Btw, I am not sure how to program endpoints of the ESC connecting it to the Neo...Should I use a linear curve (0-25-50-75-100) in the throttle curve of the TX instead the 0-0-0-0-0 and start the vbar with motor switch in the TC corresponding the motor switch position?
RV 14 August 2019 17:5214.08.2019 17:52
Endpoints for 3rd party radios:

- unmount all blades
- collective stick down
- set check in setup gov tab for direct control with stick (KEEP PANEL OPEN!!!)
- program with radio (check "survives" also a power cycle and turning on with full collective if needed)
- go into the setup gov tab again, once set and unset the check again

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Arag_ 15 August 2019 13:2615.08.2019 13:26
Got it!!

Thanks a lot for the support Rainer.

Btw, there is another detail I didn't know that is in ther Governor panel of the parameters, the Throttle out must be set to 100 for the bank you are using for the ESC programming.

But right now I got the full throttle in any position except upper 90% that the rpm seems to not change due to the motor eficciency.
VStabi VStabi Pioneer of Flybarless