above
2 August 2019 09:1502.08.2019 09:15
Hi, I want to configure the nitro governor with my spektrum DX9 station, but I can't.
I have managed to do the limits well, and that the gov starts and progressively increases the gas servo looking for the requested RPM. But I can not put the servo in engine start mode to raise the trim and adjust the idle.
Besides, the Hitec RPM sensor (HTS-MRPM) seems to be that it does not detect the magnets, I connect it and it makes me readings between 600 and 1600rpm without anything turning. This is normal ? I have connected it directly in the pure RPM.
RV
2 August 2019 10:3902.08.2019 10:39
Are you sure you have assigned the switches as required?
How is your "Kill" switch stated in the RX panels in "on / Kill" Position?
How is your "Motor" switch stated there in Off (Idle on Nitro) - AR - Run position?
Are these seperate switches?
In general - the idle can not be set though 3rd party radios from remote. it must be done with the pc software.
RPM - never tried this one, but it looks like a standard hall sensor. How did you connect it? What is the pin layout?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
3 August 2019 06:2803.08.2019 06:28
Good,
Thanks for the help, I have already set up the throttle servo for startup.
And surely the sensor is not compatible, I went to buy the align.
This sensor would be compatible?:
Https://www.rb1-rc.com/es/governor/1263-alignbeastx-governor-sensor.html
above
3 August 2019 06:4503.08.2019 06:45
Which of the sensors in this link would suit me?
https://www.amainhobbies.com/search?s=RPM+sensor
RV
3 August 2019 10:2703.08.2019 10:27
Well - lets stay on your existing sensor. How is the pin layout to connect it? As it shows a different connector (no servo connector) we should know where GND, Power and Signal is to solder a servo connector to its cable in the right polarities …
the same on the Align sensor - black is GND, red seems to be Power and white the signal. It also has a different connector and must be soldered to a servo connector.
At least - i think the HTS-MRPM might be also connected like the align one (yellow-signal) for a try.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
3 August 2019 11:0303.08.2019 11:03
My existing sensor has died. I soldered it to a servo connector correctly Black -, red +, yellow (signal), and the vbar did not detect the magnets, but it gave me 600-1600RPM with everything stopped. So what ize was to invest + and -, it was at that moment that smoke came out of the senso hitec. I think that sensor was not compatible with NEO.
I have to buy a new sensor, which one do you recommend? whichever is better and more precise. One in the engine head?
Is the Align a good low cost option?
Thank you very much for your quick response Rainer
RV
3 August 2019 18:5703.08.2019 18:57
Yes - i would use the align Sensor, i do this on my nitros too …
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
16 August 2019 15:3716.08.2019 15:37
Hi RV.
I already have the align governor sensor, and I soldered the servo connector (white-senyal, black-negative, red-positive).
Where do I have to connect the sensor? in the port of (SENSOR) or in the port of (RPM)
How can I check that the sensor is working well? since in the menu of the vbar of the pc it does not detect the magnets when I approach them in the sensor. Do I have to start the glow engine to detect the rpm?
1 mal bearbeitet. Zuletzt am 16.08.2019 15:37 von above.
RV
16 August 2019 23:5916.08.2019 23:59
The "magnet" indicator may take a while, so turn slowwwwllyyyyyyy ....
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
17 August 2019 13:0817.08.2019 13:08
OK, what port is the sensor connected to?
RV
17 August 2019 17:0417.08.2019 17:04
Sorry - it is RPM.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
20 August 2019 17:4920.08.2019 17:49
I can't get the RPM to detect me, I don't know what else to do. I've tried everything, put the poles at 1 to 2, start the engine with the Idel, but it doesn't detect anything. Without wanting to test, I connected the reverse sensor and smoke has come out of the sensor, now I have to buy another sensor.
Any ideas when I have the new sensor?
RV
20 August 2019 22:0820.08.2019 22:08
Just one:
please add a image how you would connect the new sensor.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
above
21 August 2019 12:4421.08.2019 12:44
This is how I have it connected.
https://ibb.co/m5Qwq68
What number do I have to put in the pole section?
Do I have to do any sequence of starting spice for the RPM sensor to work?
above
21 August 2019 15:3121.08.2019 15:31
Another question, just starting the engine in the Banck1 would have to mark the RPM?
above
21 August 2019 17:0321.08.2019 17:03
I just made this video so you can see that it does not detect the RPM, the sensor is far from the magnets to do different tests, but neither near nor far does it detect rpm. Nor when I enter the banck 2 that has the gov activated and rises from RPM.
https://www.youtube.com/watch?v=aYK6KGmXMvA&feature=youtu.be
above
24 August 2019 12:0824.08.2019 12:08
SOLVED! WITH THE ALIGN SENSOR, THE POLARITY HAS TO BE INVESTED IN THE CONNECTOR.
RV
24 August 2019 22:1724.08.2019 22:17
:-) :-)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.