reggie
30 July 2020 01:0130.07.2020 01:01
I have Jeti radio ds 16 and duplex rex10 receiver.IM not quite sure what is not binding the radio or the receiver.
Neo turns solid green when I power up the receiver. When I power up the radio neo freaks out and goes fast red blinking. I think its the receiver and radio not binding. Receiver is configured in device explorer of radio and I'm using UDI receiver set up. one wire set up. When I use another receiver same thing happens .At a stand still been at this for days now. need help!!
RV
30 July 2020 10:5530.07.2020 10:55
I am sorry - i don't have any 3rd party equipment here.
Is there probably something to configure for the UDI output in TX/RX?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
R@VBar
1 August 2020 14:4401.08.2020 14:44
Hi reggie,
what exactly have you configured on your rex 10? did you update to newest software? if you can configure the receiver in device explorer it is correctly bound... you anyhow can rebind it to be sure...
the key steps i had to do:
in Jeti Tx device explorer, select the rex and:
1. in main settings: speed = 10ms (Tx should be set at 100Hz) , number of channels 8 or 9 or whatever you need, PPM/UDI mode = "direct"
2. in fail safe: deactivate it (inactive)... failsafe should be handled by NEO only
3. alt. functions: one of E1/E2 must be set to "Serial UDI 12ch" - this is where you connect the NEO.
then in NEO setup
1. set connection to UDI - at this point i had to restart the NEO (i converted from Spektrum to Jeti)
2. map your channels to your needs
3. check channels mapping, 0 and +/- 100% ... i had to set all channels to +/- 107% in Jeti Tx "Servo Settings"
... that's what i did and 5 NEOs are flying perfectly using Rex3... nothing else i had to do
Ciao
Michael
1 mal bearbeitet. Zuletzt am 01.08.2020 14:46 von R@VBar.
reggie
1 August 2020 19:4001.08.2020 19:40
Thanks for replying. But I did all that. The Neo blinks red /green when powered up.as soon I power up the radio it rapidly blinks red.It say receiver bound but the Neo never goes solid green. Receiver is configured in device explorer. After choosing UDI in Neo I cycle the power and still problem. At what stage should I turn the radio on?
Thanks...
reggie
2 August 2020 03:5502.08.2020 03:55
Oh yes just realized so anxious to fly.....needed to update receiver.Shes good to go now.
Thanks Guys....
reggie
2 August 2020 20:1202.08.2020 20:12
Sorry for the confusion. I started to use the set up wizard everything was fin all systems bound and coming along nicely. I had to step away so I shut everything down as I should.
The next day started up everything and the same problem occurring again. Red light flashing quickly neo not bound to receiver etc. Need help as to why this is happening again?
R@VBar
3 August 2020 07:2703.08.2020 07:27
can you post a photo of your Rx to NEO cabling? and your Rx setup and software versions?
Eddi E. aus G.
5 August 2020 11:5405.08.2020 11:54
Hi,
sorry to ask only now, but ... what does the event log tell us? I mean, if the NEO flashes red, it's a warning, and the cause can be found in the log.
Kind regards
Eddi
Born to fly ...
forced to work.