Razmo
23 April 2021 17:4123.04.2021 17:41
Now being familiar with the original Mini Vbar 5.3 Pro software via my JR 12X Transmitter. I purchased a NEO w/express for my Logo 550 for use with my JR 12X. A few questions…
1) Am I not able to configure the PC software for remote tail gain adjustment prior to configuring bank switching like I have done with my Mini Vbar v5.3?
2) Can I make Expo adjustments from my 12X or am I required to use the PC software? I'm not seeing an advanced tab for Expo adjustment like I have in v5.3 Pro for the mini.
3) Being familiar with the Mini v5.3, since it may make take a handful of flights to find the preferred head speed, gains, etc. My methodology has been to keep both the main rotor and tail optimizer unchecked, including Auto Trim, until I am ready for such. Should I do the same with the NEO?
Thank You,
Nick
RV
23 April 2021 23:2023.04.2021 23:20
1 - Just configure additionally to the bank swithcung a channel for Gain - see RX Tab.
2 - Having 6.4 Pro - you can do this. Not with Express.
3 - yes, this would be the same.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Razmo
23 April 2021 23:4623.04.2021 23:46
Regarding #1... I take a look, thank you. I may have further questions here..
Regarding #2... Do you mean Express doesn't allow for expo adjustment either remotely from my Transmitter or the PC software?
Thanks,
Raz
RV
24 April 2021 08:1124.04.2021 08:11
In Express we have a fixed built in Expo. The same as the deafults on pro.
You can add TX expo ofcourse - but the resulting curves might be strange if you add a lot of the TX Expo.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Razmo
26 April 2021 14:4126.04.2021 14:41
Can you be more specific? What is the fixed expo % for Express? Is it the same for both the main rotor and tail rotor? It sounds as if Express doesn't really allow for Expo adjustments from the transmitter (or the PC software) unless you're using Vcontrol.
Raz
Eddi E. aus G.
26 April 2021 15:4426.04.2021 15:44
Hello Raz,
Express has all the Expert parameters set to sensible defaults.
Essential was that a helicopter flies approximately the same as you were used to, when coming from flybar+paddles and a standalone tail gyro.
The feel was achieved with 10 % of expo on aileron/elevator and 50 % of expo on the tail, given our way to calculate the expo curve (there is no standard ...).
For the tail, this sounds huge, but in fact this makes the tail feel like a Futaba GYxxx controlled tail rotor, less would be too direct.
Now, you can use your expo settings from the radio on top, and that's not even bad.
It's just that the resulting curve would look slightly different if you would draw it, diagonal, one expo curve below, another below that, and the resulting curve if you modify one with the next.
I doubt you really feel it, in flight.
And it's been that way all the time, now, even years before VBar Control.
With Pro, you have the choice, either only use VBar expo, or only use radio expo (zero out VBar expo, then), or still use both and adjust here or there.
I bet most pilots have used it this way and use it this way without knowing, and without any negative effect.
Bottom line, do the basic setup using the computer, set agility and yaw rate as well as main rotor and tail rotor gain to the maximum you ever want (respectively: what your heli can handle, for specific rpm), then use flight conditions in your radio to adjust dual rate (agility and yaw rate) and expo, to adjust for e.g. different head speeds and flight situations.
In the end, if you fly the machine, you will find it's much simpler than you thought ;-)
—Eddi
Born to fly ...
forced to work.
Razmo
26 April 2021 20:5226.04.2021 20:52
Appreciate it Eddi! Very helpful, thank you.
Raz