gmccluskey
26 July 2021 21:3626.07.2021 21:36
I have a VBar Neo with an external sensor connected (and the satellite is initialized in the software). When the unit turns on, the LED on top eventually turns green but the satellite unit continues to change colors. Is this normal? I seem to recall it turning green also when I first installed it.
1 mal bearbeitet. Zuletzt am 27.07.2021 06:07 von RV.
RV
26 July 2021 22:5126.07.2021 22:51
Hello,
it is not clear what you are talking about:
- a external gyro sensor
or
- a external RX satellite
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
gmccluskey
27 July 2021 00:4427.07.2021 00:44
Sorry, the external gyro. The satellite gyro continues to sequence through different colours after the main unit is showing a solid green light. Is this normal?
Also, I noticed that when you slightly wiggle the wire going into the satellite gyro, the tail servo moves slightly. I thought that the satellite was a backup to the main Neo unit and is ineffective until the main unit fails.
RV
27 July 2021 06:0627.07.2021 06:06
The external gyro is taken first when connected. The internal one takes over for rescue, lightness function and in case of a total (cable comes off) loss of the external one.
As the external one has way less resolution we recommend using it only when it is impossible to use the internal sensor. Although you should not use rescue and lightness then because this is done with the internal sensor (the external does not have accelerometers).
So - it can be used as a kind of redundancy for flight, but it is definitely best not to need it at all.
The external one is calibrated during boot with the internal one - and if there are too much differencies it may show this with changing colurs. Are both sensor orientations set in the right way?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Eddi E. aus G.
27 July 2021 09:1327.07.2021 09:13
Hi,
about the external sensor and it's colors, it's normal.
If left alone, you see the color rotation.
If you move it cleanly by either elevator, aileron, tail axis, it will light up green, red, blue respectively, as a feedback for activity on that axis.
If it was flickering if left alone, or off, or showing just one color, that would indicate that it's out of calibration, or unquiet.
Very likely, the VBar (legacy main unit or NEO) would then already warn at power up, too, with a noticeable 30+ pitch twitch, and with log file entries.
Kind regards
Eddi
Born to fly ...
forced to work.
gmccluskey
27 July 2021 14:3227.07.2021 14:32
Both sensors are oriented the correct way. Just sitting on the bench, the external gyro is sequencing through different colours, while the main Neo unit is solid green. The unit does light up green, red and blue when moving in the elevator, aileron and tail axis as described.so, it Looks like everything is correct. Thanks for clarifying this.
I have been using both the main and satellite gyros in my Logo 550 since new. Would I be better off just removing the external gyro?
Regards,
George
Eddi E. aus G.
27 July 2021 14:3927.07.2021 14:39
Hi George,
it doesn't hurt, but over the years we found it's hardly ever necessary, even on nitros, gassers, other helis with high/adverse vibration.
Some pilots prefer the characteristics of the older sensors.
Those who don't benefit from the higher accuracy :-)
You can disable it in the software, to see if you notice any difference.
Or just disconnect the wire.
Kind regards
Eddi
Born to fly ...
forced to work.