← VBar NEO for external transmitters

Help with post crash event log/troubleshooting translated

VBar › VBar NEO for external transmitters · Started by CaptainMitch119 on 30 May 2024 02:1530.05.2024 02:15
CaptainMitch119 30 May 2024 02:1530.05.2024 02:15
Hello,

I am looking for help interpreting a post crash event log. A few days ago I suffered a crash of my Logo 700 from apparent control loss. The crash happened very early in the flight while performing a tail down tic toc. The crash happened very quickly so it is hard to remember exactly what happened, but I remember feeling like I had no control. Looking at the Neo event log after the flight revealed that the system logged RC packed loss and an activation of the failsafe. I was fairly surprised by this because this is a helicopter that I have several hundred flights on, and have never had any kind of radio problems with. I should also note that the crash happened probably no more than 50ft away from me, so very short range. The radio system is a pair of spektrum satellites plugged into the Neo with a DX9 transmitter. After the crash and aside from the damage sustained, I did find one satellite cable had chafing which exposed metal on 2 of the three wires. I found I was able to short the Neo by bridging the two wires with a screwdriver (terrible idea I know) and was hoping to see a similar event log but it was completely different showing a warmstart instead which you can see in the log. I should also mention that the radio system appears to still function more or less normally after the crash. Also the 1 prior RC failsafe activation in the log is almost certainly due to me unplugging my receiver pack and the backup power system keeping it on as its a new system to me and I mess up my power down sequence sometimes.

I am asking is for opinions on whether the chafed satellite wire could have been the primary culprit or if I am looking for another electrical system problem, and if so, what kinds of tests and troubleshooting do I need to do to make sure this doesn't happen again immediately. I plan to fix the helicopter as parts are still available, but I want to be sure I am careful moving forward. Obviously I will at minimum replace the satellite wires, and perhaps the satellites themselves with new units and perform range checking once I get it all back together. Thank you for reading.

Helicopter Configuration
Logo 700
Age: ~6 years
1 Prior crash with significant damage
ESC: Castle Phoenix HV 160
Motor: Scorpion HK-4525-520KV
Servos: 3x Xpert GS-6401, 1x Xpert GS-3302T
Receiver: 2x Spektrum DSMX satellites
Servo/Receiver power: 2s 5000mah Lipo battery direct to Neo
Backup power: Xguard RC capacitor
Main Power: 12s 5000mah Lipo
Transmitter: Spektrum DX9

Event Log (Do not mind the timestamp, field laptop is stubborn):
Tue Jan 01 00:54:48 EST 2002
Serial: 20018940
Firmware: 6.4
Patchlevel: 87
---- start ----
Info 0:01 Governor is at Low Throttle Limit
Info 0:10 Governor is at Low Throttle Limit
OK 0:20 Good Health Message (10sec)
Info 0:28 Raised Vibration Level
Info 0:29 Governor is at Low Throttle Limit
Info 0:38 Raised Vibration Level
Info 0:47 Raised Vibration Level
Info 0:48 Governor is at Low Throttle Limit
Info 0:49 Governor is at Low Throttle Limit
Info 0:56 Raised Vibration Level
Info 0:56 Governor is at Low Throttle Limit
Info 1:02 Governor is at Low Throttle Limit
Info 1:05 Raised Vibration Level
Info 1:14 Raised Vibration Level
OK 1:24 Good Health Message (10sec)
OK 1:34 Good Health Message (10sec)
OK 1:44 Good Health Message (10sec)
OK 1:54 Good Health Message (10sec)
Info 2:00 Governor is at Low Throttle Limit
OK 2:10 Good Health Message (10sec)
Info 2:17 Governor is at Low Throttle Limit
Info 2:20 Governor is at Low Throttle Limit
Info 2:28 Raised Vibration Level
OK 2:38 Good Health Message (10sec)
OK 2:48 Good Health Message (10sec)
OK 2:58 Good Health Message (10sec)
OK 3:08 Good Health Message (10sec)
OK 3:18 Good Health Message (10sec)
Info 3:19 Governor is at Low Throttle Limit
Info 3:20 Governor OFF
Info 3:20 Governor Mode Stop
Info 3:20 Motor Switch operated to OFF
Info 3:20 Motor Switch operated to Idle bailout
Info 3:23 Raised Vibration Level
OK 3:33 Good Health Message (10sec)
OK 3:43 Good Health Message (10sec)
OK 3:53 Good Health Message (10sec)
OK 4:03 Good Health Message (10sec)
OK 4:13 Good Health Message (10sec)
OK 4:23 Good Health Message (10sec)
OK 4:33 Good Health Message (10sec)
OK 4:43 Good Health Message (10sec)
OK 4:53 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
OK 0:15 Good Health Message (10sec)
OK 0:25 Good Health Message (10sec)
OK 0:35 Good Health Message (10sec)
OK 0:45 Good Health Message (10sec)
OK 0:55 Good Health Message (10sec)
OK 1:05 Good Health Message (10sec)
OK 1:15 Good Health Message (10sec)
OK 1:25 Good Health Message (10sec)
OK 1:35 Good Health Message (10sec)
OK 1:45 Good Health Message (10sec)
OK 1:55 Good Health Message (10sec)
OK 2:05 Good Health Message (10sec)
OK 2:15 Good Health Message (10sec)
OK 2:25 Good Health Message (10sec)
OK 2:35 Good Health Message (10sec)
Info 2:43 Bank 2 Loaded
OK 2:53 Good Health Message (10sec)
OK 3:03 Good Health Message (10sec)
OK 3:13 Good Health Message (10sec)
Info 3:18 Governor Mode Pitch
Info 3:18 Motor Switch operated to Idle bailout
Info 3:18 Motor Switch operated to ON
Info 3:27 Raised Vibration Level
Info 3:36 Raised Vibration Level
Critical 3:45 Extreme Vibration Level
Info 3:54 Raised Vibration Level
Info 4:04 Raised Vibration Level
Info 4:13 Raised Vibration Level
OK 4:23 Good Health Message (10sec)
OK 4:33 Good Health Message (10sec)
Info 4:40 Raised Vibration Level
OK 4:50 Good Health Message (10sec)
OK 5:00 Good Health Message (10sec)
Warn 5:08 High Vibration Level
OK 5:18 Good Health Message (10sec)
Info 5:26 Raised Vibration Level
Info 5:35 Raised Vibration Level
OK 5:45 Good Health Message (10sec)
OK 5:55 Good Health Message (10sec)
OK 6:05 Good Health Message (10sec)
Info 6:12 Raised Vibration Level
OK 6:22 Good Health Message (10sec)
Info 6:30 Raised Vibration Level
Warn 6:40 High Vibration Level
OK 6:50 Good Health Message (10sec)
OK 7:00 Good Health Message (10sec)
OK 7:10 Good Health Message (10sec)
OK 7:20 Good Health Message (10sec)
OK 7:30 Good Health Message (10sec)
Info 7:35 Raised Vibration Level
OK 7:45 Good Health Message (10sec)
Info 7:51 Governor OFF
Info 7:51 Governor Mode Stop
Info 7:51 Motor Switch operated to OFF
Info 7:51 Motor Switch operated to Idle bailout
OK 8:01 Good Health Message (10sec)
OK 8:11 Good Health Message (10sec)
OK 8:21 Good Health Message (10sec)
OK 8:31 Good Health Message (10sec)
OK 8:41 Good Health Message (10sec)
OK 8:51 Good Health Message (10sec)
OK 9:01 Good Health Message (10sec)
OK 9:11 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
Info 0:01 Bank 1 Loaded
Info 0:05 Calibration Finished
OK 0:15 Good Health Message (10sec)
OK 0:25 Good Health Message (10sec)
OK 0:35 Good Health Message (10sec)
OK 0:45 Good Health Message (10sec)
OK 0:55 Good Health Message (10sec)
OK 1:05 Good Health Message (10sec)
OK 1:15 Good Health Message (10sec)
OK 1:25 Good Health Message (10sec)
OK 1:35 Good Health Message (10sec)
OK 1:45 Good Health Message (10sec)
OK 1:55 Good Health Message (10sec)
OK 2:05 Good Health Message (10sec)
OK 2:15 Good Health Message (10sec)
OK 2:25 Good Health Message (10sec)
OK 2:35 Good Health Message (10sec)
Info 2:39 Bank 2 Loaded
Info 2:46 Bank 3 Loaded
Info 2:52 Bank 2 Loaded
Info 2:53 Bank 1 Loaded
Info 2:55 Bank 2 Loaded
Info 2:56 Bank 3 Loaded
Info 2:58 Bank 2 Loaded
Info 2:59 Bank 3 Loaded
Info 3:09 Bank 2 Loaded
Info 3:10 Bank 1 Loaded
Info 3:17 Bank 2 Loaded
Info 3:17 Bank 3 Loaded
Info 3:18 Bank 2 Loaded
Info 3:19 Bank 1 Loaded
Info 3:26 Bank 2 Loaded
Info 3:26 Bank 3 Loaded
Info 3:27 Bank 1 Loaded
Info 3:27 Bank 2 Loaded
OK 3:37 Good Health Message (10sec)
OK 3:47 Good Health Message (10sec)
OK 3:57 Good Health Message (10sec)
OK 4:07 Good Health Message (10sec)
OK 4:17 Good Health Message (10sec)
OK 4:27 Good Health Message (10sec)
OK 4:37 Good Health Message (10sec)
OK 4:47 Good Health Message (10sec)
OK 4:57 Good Health Message (10sec)
OK 5:07 Good Health Message (10sec)
Warn 5:11 RC Input Packet lost
Critical 5:11 RC Failsafe has been activated
OK 5:21 Good Health Message (10sec)
OK 5:31 Good Health Message (10sec)
OK 5:41 Good Health Message (10sec)
OK 5:51 Good Health Message (10sec)
OK 6:01 Good Health Message (10sec)
OK 6:11 Good Health Message (10sec)
OK 6:21 Good Health Message (10sec)
OK 6:31 Good Health Message (10sec)
OK 6:41 Good Health Message (10sec)
OK 6:51 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
OK 0:15 Good Health Message (10sec)
OK 0:25 Good Health Message (10sec)
OK 0:35 Good Health Message (10sec)
OK 0:45 Good Health Message (10sec)
OK 0:55 Good Health Message (10sec)
OK 1:05 Good Health Message (10sec)
OK 1:15 Good Health Message (10sec)
OK 1:25 Good Health Message (10sec)
OK 1:35 Good Health Message (10sec)
OK 1:45 Good Health Message (10sec)
OK 1:55 Good Health Message (10sec)
OK 2:05 Good Health Message (10sec)
OK 2:15 Good Health Message (10sec)
OK 2:25 Good Health Message (10sec)
OK 2:35 Good Health Message (10sec)
OK 2:45 Good Health Message (10sec)
OK 2:55 Good Health Message (10sec)
OK 3:05 Good Health Message (10sec)
OK 3:15 Good Health Message (10sec)
OK 3:25 Good Health Message (10sec)
OK 3:35 Good Health Message (10sec)
OK 3:45 Good Health Message (10sec)
OK 3:55 Good Health Message (10sec)
OK 4:05 Good Health Message (10sec)
OK 4:15 Good Health Message (10sec)
OK 4:25 Good Health Message (10sec)
OK 4:35 Good Health Message (10sec)
OK 4:45 Good Health Message (10sec)
OK 4:55 Good Health Message (10sec)
OK 5:05 Good Health Message (10sec)
OK 5:15 Good Health Message (10sec)
OK 5:25 Good Health Message (10sec)
OK 5:35 Good Health Message (10sec)
Info 5:39 Bank 2 Loaded
Info 5:41 Governor Mode Pitch
Info 5:41 Motor Switch operated to Idle bailout
Info 5:41 Motor Switch operated to ON
Warn 5:45 High Vibration Level
Info 5:54 Raised Vibration Level
Warn 5:56 RC Input Packet lost
Critical 5:56 RC Failsafe has been activated
Critical 5:56 Aileron Sensor Value out of Range
Warn 5:56 Supply Voltage dropped below 4.5V
Info 5:56 Governor Sensor no Signal
Warn 5:57 The Cyclic Ring is active
Warn 5:57 RC Input Packet lost
Critical 5:57 RC Failsafe has been activated
Warn 6:03 High Vibration Level
OK 6:13 Good Health Message (10sec)
OK 6:23 Good Health Message (10sec)
OK 6:33 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
OK 0:15 Good Health Message (10sec)
OK 0:25 Good Health Message (10sec)
OK 0:35 Good Health Message (10sec)
OK 0:45 Good Health Message (10sec)
OK 0:55 Good Health Message (10sec)
OK 1:05 Good Health Message (10sec)
OK 1:15 Good Health Message (10sec)
Info 1:23 Bank 2 Loaded
Info 1:23 Bank 3 Loaded
Info 1:24 Bank 1 Loaded
Info 1:24 Bank 2 Loaded
OK 1:34 Good Health Message (10sec)
Info 1:38 Bank 2 Loaded
Info 1:40 Bank 2 Loaded
Info 1:40 Bank 3 Loaded
Info 1:41 Bank 3 Loaded
OK 1:51 Good Health Message (10sec)
Info 1:54 Bank 1 Loaded
Info 1:54 Bank 2 Loaded
OK 2:04 Good Health Message (10sec)
OK 2:14 Good Health Message (10sec)
OK 2:24 Good Health Message (10sec)
OK 2:34 Good Health Message (10sec)
OK 2:44 Good Health Message (10sec)
OK 2:54 Good Health Message (10sec)
OK 3:04 Good Health Message (10sec)
OK 3:14 Good Health Message (10sec)
OK 3:24 Good Health Message (10sec)
OK 3:34 Good Health Message (10sec)
OK 3:44 Good Health Message (10sec)
OK 3:54 Good Health Message (10sec)
Warn 3:55 RC Input Packet lost
Warn 3:56 RC Input Packet lost
Critical 3:56 RC Failsafe has been activated
Info 4:04 Bank 1 Loaded
OK 4:14 Good Health Message (10sec)
OK 4:24 Good Health Message (10sec)
OK 4:34 Good Health Message (10sec)
OK 4:44 Good Health Message (10sec)
OK 4:54 Good Health Message (10sec)
OK 5:04 Good Health Message (10sec)
OK 5:14 Good Health Message (10sec)
OK 5:24 Good Health Message (10sec)
OK 5:34 Good Health Message (10sec)
OK 5:44 Good Health Message (10sec)
OK 5:54 Good Health Message (10sec)
OK 6:04 Good Health Message (10sec)
OK 6:14 Good Health Message (10sec)
OK 6:24 Good Health Message (10sec)
OK 6:34 Good Health Message (10sec)
OK 6:44 Good Health Message (10sec)
OK 6:54 Good Health Message (10sec)
OK 7:04 Good Health Message (10sec)
OK 7:14 Good Health Message (10sec)
OK 7:24 Good Health Message (10sec)
OK 7:34 Good Health Message (10sec)
OK 7:44 Good Health Message (10sec)
OK 7:54 Good Health Message (10sec)
OK 8:04 Good Health Message (10sec)
OK 8:14 Good Health Message (10sec)
OK 8:24 Good Health Message (10sec)
OK 8:34 Good Health Message (10sec)
OK 8:44 Good Health Message (10sec)
OK 8:54 Good Health Message (10sec)
OK 9:04 Good Health Message (10sec)
OK 9:14 Good Health Message (10sec)
OK 9:24 Good Health Message (10sec)
OK 9:34 Good Health Message (10sec)
OK 9:44 Good Health Message (10sec)
OK 9:54 Good Health Message (10sec)
OK 10:04 Good Health Message (10sec)
OK 10:14 Good Health Message (10sec)
OK 10:24 Good Health Message (10sec)
OK 10:34 Good Health Message (10sec)
OK 10:44 Good Health Message (10sec)
OK 10:54 Good Health Message (10sec)
OK 11:04 Good Health Message (10sec)
OK 11:14 Good Health Message (10sec)
OK 11:24 Good Health Message (10sec)
OK 11:34 Good Health Message (10sec)
Warn 11:41 RC Input Packet lost
Warn 11:42 RC Input Packet lost
Critical 11:42 RC Failsafe has been activated
OK 11:52 Good Health Message (10sec)
OK 12:02 Good Health Message (10sec)
OK 12:12 Good Health Message (10sec)
OK 12:22 Good Health Message (10sec)
OK 12:32 Good Health Message (10sec)
OK 12:42 Good Health Message (10sec)
OK 12:52 Good Health Message (10sec)
OK 13:02 Good Health Message (10sec)
OK 13:12 Good Health Message (10sec)
Info 13:13 Motor Switch operated to Idle bailout
OK 13:23 Good Health Message (10sec)
OK 13:33 Good Health Message (10sec)
OK 13:43 Good Health Message (10sec)
OK 13:53 Good Health Message (10sec)
OK 14:03 Good Health Message (10sec)
OK 14:13 Good Health Message (10sec)
OK 14:23 Good Health Message (10sec)
OK 14:33 Good Health Message (10sec)
OK 14:43 Good Health Message (10sec)
OK 14:53 Good Health Message (10sec)
Info 14:54 Bank 2 Loaded
Info 14:54 Motor Switch operated to Idle bailout
Info 14:55 Bank 1 Loaded
Info 14:55 Motor Switch operated to OFF
Info 14:59 Calibration Finished
OK 15:09 Good Health Message (10sec)
OK 15:19 Good Health Message (10sec)
OK 15:29 Good Health Message (10sec)
OK 15:39 Good Health Message (10sec)
OK 15:49 Good Health Message (10sec)

Critical 0:00 Warmstart

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)

Critical 0:00 Warmstart

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)

OK 0:00 Reset Reason: Power On

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
Info 0:05 Calibration Finished
OK 0:15 Good Health Message (10sec)
OK 0:25 Good Health Message (10sec)
OK 0:35 Good Health Message (10sec)
OK 0:45 Good Health Message (10sec)
OK 0:55 Good Health Message (10sec)
OK 1:05 Good Health Message (10sec)
OK 1:15 Good Health Message (10sec)
OK 1:25 Good Health Message (10sec)
OK 1:35 Good Health Message (10sec)
OK 1:45 Good Health Message (10sec)
OK 1:55 Good Health Message (10sec)
OK 2:05 Good Health Message (10sec)

Critical 0:00 Warmstart

Info 0:00 Bank 1 Loaded

Info 0:00 Bank 2 Loaded

Info 0:00 Motor Switch operated to OFF

Info 0:00 Motor Switch operated to Idle bailout
OK 0:10 Good Health Message (10sec)
OK 0:20 Good Health Message (10sec)
OK 0:30 Good Health Message (10sec)
OK 0:40 Good Health Message (10sec)
OK 0:50 Good Health Message (10sec)
OK 1:00 Good Health Message (10sec)
OK 1:10 Good Health Message (10sec)
OK 1:20 Good Health Message (10sec)
OK 1:30 Good Health Message (10sec)
OK 1:40 Good Health Message (10sec)
OK 1:50 Good Health Message (10sec)
OK 2:00 Good Health Message (10sec)
OK 2:10 Good Health Message (10sec)
OK 2:20 Good Health Message (10sec)
OK 2:30 Good Health Message (10sec)
OK 2:40 Good Health Message (10sec)
OK 2:50 Good Health Message (10sec)
OK 3:00 Good Health Message (10sec)
OK 3:10 Good Health Message (10sec)
OK 3:20 Good Health Message (10sec)
OK 3:30 Good Health Message (10sec)
OK 3:40 Good Health Message (10sec)
OK 3:50 Good Health Message (10sec)
OK 4:00 Good Health Message (10sec)
OK 4:10 Good Health Message (10sec)
---- end ----



1 mal bearbeitet. Zuletzt am 30.05.2024 02:26 von CaptainMitch119.
RV 30 May 2024 13:3030.05.2024 13:30
Quote:Info 5:39 Bank 2 Loaded
Info 5:41 Governor Mode Pitch
Info 5:41 Motor Switch operated to Idle bailout
Info 5:41 Motor Switch operated to ON
Warn 5:45 High Vibration Level
Info 5:54 Raised Vibration Level
Warn 5:56 RC Input Packet lost
Critical 5:56 RC Failsafe has been activated
Critical 5:56 Aileron Sensor Value out of Range
Warn 5:56 Supply Voltage dropped below 4.5V
Info 5:56 Governor Sensor no Signal
Warn 5:57 The Cyclic Ring is active
Warn 5:57 RC Input Packet lost
Critical 5:57 RC Failsafe has been activated
Warn 6:03 High Vibration Level

Hello,

this might be the situation where it happened (Sensor message shows the "impact&quot ;-) .

I can't find any things instead of there must have been a situation where either both satellites had no reception or the signal input was disturbed. As you figured out the power supply will have other issues at this sockets if shortened.

I would chek all by doing some test runs w/o blades and have a look at the logs. Then i would take care that the motor plate and tail boom as well as tail gear have a electrical connection (i use a thin single servo cable wire), the tail drive in between may give some statics. In addition to this the motor insulation could also be checked, especially fo no gap at the plugs from/to ESC (use heat shrink).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
CaptainMitch119 30 May 2024 21:1230.05.2024 21:12
Thank you for the reply.

I will have to get some parts on order and get everything back together and do some testing without blades. I do have a static wire that goes from the motor plate to the tail drive as this section is belt driven on the Logo 700, and it has good continuity per a multimeter check post crash. There is no stock provision for connecting the tail boom into that as well. One of my antennas as well as the flash lights for the backup power system ride on the tail boom. The tail is torque tube driven so is it still worth it to connect the tail boom? I do have some small gaps on the ESC wires at the bullet connections so I will be sure to cover that with additional shrink tube. I am very surprised by this sudden radio problem and really looking for some kind of on board issue that might have caused it. The DX9 I use is getting older, but I have not had any other issues like this, the day of the heli crash I flew a plane three times and had no problem. I guess the best thing to do is get the heli back together and just test it out.

Thanks,

Mitch
RV 31 May 2024 00:2431.05.2024 00:24
I would also test the sats in single - just by disconnecting one of them and see if the other will work (on the bench of course).

regards (EN) / Gruss (DE)

Rainer Vetter

_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.

Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
VStabi VStabi Pioneer of Flybarless