Sbahzad
15 June 2026 19:0215.06.2026 19:02
i have updated the logo 200 trainer to pro + rescue software. and connected to my vbar evo remote. now i try to connect back to trainer (vbar basic) and updated the software back to navi software but it does not connect as trainer.
how can i connect it back to the trainer mode? flipping the trainer switch on / off does not do any thing.
Sbahzad
15 June 2026 19:1415.06.2026 19:14
i have set new model from the vbar basic and now i t can detect the trainer mode. but i cannot get the control? remote says move collective up , i do so but no response. and i can see the swash is tilted forward. how can i fix it
RV
15 June 2026 21:2615.06.2026 21:26
Welll - probably wrong stickmode set in the radio than physically exists on the sticks?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Welll - probably wrong stickmode set in the radio than pysically exists on the sticks?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Sbahzad
16 June 2026 06:2916.06.2026 06:29
stick mode is correct. and confirmed from bar indicator on main page for collective, elevator, aileron, rudder.
i am removing the blades and testing. raising the heli with my hand, then keep it study as hover. originally when i hover and move the sticks it give a beep sound then i have control. now i am not getting this sound or control.
Eddi E. aus G.
18 June 2026 11:1718.06.2026 11:17
Hi,
OK, let's try and start over:
The model (serial no. 20046894?) must have the Flight Trainer firmware ('Navi').
According to vstabi.info, it does. Check.
The setup on the model must bei the Trainer Setup (you can (re-)do that either from your VBar Control EVO (LOGO 200 TR), or from VBar Control Basic).
Next steps would be, trim the swash plate by eyeballing it, level and 0° collective, then do the automated flight trainer trim flight to fine-tune (you can do that either from your VBar Control EVO _if_ you have the Apps installed—after an update of your VBar Control EVO, you have—, or your VBar Control Basic).
On VBar Control EVO, when bound that way, you can assign the required switches (Take off/Land, Motor, Trainer (which is basically the Rescue Switch in it' Trainer position). Triple check so you have no adverse double-occupancy, and make sure that if you want to fly the 200 as a Trainer, the Bank Switch _must be_ in Bank 1 position, and the parameter set of Bank 1 must not be changed.
Of course, to enable Flight Trainer, both the platform _and_ the model must be switched on and bound to the same transmitter you intend to control it with.
Without the platform in the loop, LOGO 200 is just LOGO 200.
On VBar Control Basic (both actually), you'd have to check if the stick mode is correct, and on Basic particularly that the switch selection 3x2 (three two-way switches) or 6x3 (six three-way-switches) is selected properly, and that the functions are assigned properly. If in doubt, there are Reset options in Basic's Menu, from there on, it's quite self-explanatory ... I hope :-)
Hope this helps!
—Eddi
Born to fly ...
forced to work.