Bell407
11 May 2017 18:2311.05.2017 18:23
Hi guys. My questions could fall into several categories: Logo 700, VControl, and NEO. Let me outline them and go from there.
Here is my setup (everything purchased new from Mikado):
Logo 700
NEO with internal V-link (upgraded to Pro Rescue)
VControl
Tribunus 200A ESC
Scorpion HK4525-520 Ultimate
Pulse 12S-6000 (2 6000mAh 6S packs)
MKS servos all around
Charger: ProgressiveRC pelican case setup with iCharger 308 duo, big power supply, etc. (charging is not an issue)
My background is straight from the nitro and gasser world (Miniature Aircraft helis) with the last time I flew being approximately 8 years ago. My style is purely a sport-flyer, scale, minimal 3D, etc. This is my 1st real experience with electric equipment, which admittedly puts me in the mindset of "how much fuel (in this case battery capacity) do I have remaining"? This is important to me since I am trying to maximize flight time just like I did with the fuel helis. One of the ways I will do this is to run a very modest head speed (1000-1200 perhaps).
Questions:
1) Does the NEO I am running with all the capabilities, Apps installed, etc. have the ability to monitor battery usage after each flight?
I think the answer is YES because after powering down the helicopter the Vcontrol presents a "flight summary", which shows "Used Capa" in mAH and "Remaining C" in % along with a variety of other parameters.
2) Does the NEO monitor real time battery consumption during the flight and can it be set up via telemetry to make programmed voice callouts as the battery capacity is consumed during the flight?
I think the answer is NO and in order to do that I would need to equip the Logo with a UI sensor, correct? There are YouTube videos out there that demonstrate the UI sensor. Pilots that have them really like the idea of using the capacity consumption callouts rather than a flight timer. This is something I should look into as well.
3) If a UI sensor is required for what I want to do, what port on the NEO do I plug in the telemetry cable from the sensor given that I am already using 1 port from the ESC and will likely use the other port if/when I go to the RFID battery tag option?
4) How do I take screenshots on the VControl? I read in the instructions and here on the VBar Control section that you assign the capability to an optional switch. Can someone expand on this a bit please?
5) What is the correct way to eliminate (or reduce to a negligible amount) any sort of tail wag on my Logo?
This is something I have always struggled with even on nitros. My Logo is butter smooth in every aspect but when I am sitting in a hover the tail just hunts back and forth an inch or so either side (annoying). I don't notice any bounce back after and aggressive stick input. Is this a function of too low or too high of gain? Everything was set dead on during the initial setup as far as end points and so forth. I can try it in another head speed bank to see if that makes a difference but I don't think it will. Let me know if you need additional info here.
That is all for now guys. I absolutely love everything about this helicopter and Mikado support. This is simply a matter of me getting my head wrapped around the "electric" side of the hobby. With your help I am sure I will get there!
Thanks,
Nick Shepler
Danville, IN
RV
11 May 2017 21:4711.05.2017 21:47
1 - yes - all data on summary screen is stored in a log for each battery - and in addition a detailed log can be enabled. All files are located on your VBar Control then - and - here is a superb tool for viewing them as graph etc:
http://www.vstabi.info/en/node/1696 (Read also the following pages)
http://www.vstabi.info/forum/read.php?42,139055
2 - yes, it uses the scorpion data and calls every 10% from the set up capacity for flight (read links above). E.g. if you set up to use 70% of a 5000 battery - it will take the 3500 as 100% for announcements - so just land when 0% is spoken and still 1500 left ;-)
3 - not needed, just use the scorpion app
http://www.vstabi.info/en/sc
4 - use the regarding app. once you toggle the assigned swith it will shoot and store (you will hear a beep). the shots can be viewed with VBC and also transferred to pc through USB.
http://www.vstabi.info/en/node/1607
5 - almost too low gain or a bit of friction in the tail linkages.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Bell407
12 May 2017 05:1312.05.2017 05:13
Thanks for the responses Rainer.
One question I had after looking at the battery log info is in regards to plugging in a battery that is not fully charged.
Lets assume I have a 6000 mAh pack that I have drained down to 4000 mAh on a previous flight. If I don't charge the pack, power the heli back up, and get the battery warning about it not being fully charged, does the NEO and/or the Tribunus know how much capacity is remaining in the packs? If so, does it know it in mAh capacity and lastly is there a way for me to see that number before I fly?
Best regards,
Nick
Jason Bell
12 May 2017 19:1812.05.2017 19:18
Quote:If I don't charge the pack, power the heli back up, and get the battery warning about it not being fully charged, does the NEO and/or the Tribunus know how much capacity is remaining in the packs?
It does not know the remaining mAh inside of a drained pack. It will tell you voltage, so if you are using talking telemetry to speak voltage, then I suppose it "sort of" knows.
Quote:If so, does it know it in mAh capacity and lastly is there a way for me to see that number before I fly?
Don't believe so, only voltage. You can see the live voltage within the Scorpion App
Bell407
4 June 2017 03:2504.06.2017 03:25
Hey guys,
Another question for you. My setup is shown in my first post above. The problem I am having is the inability to change head speed using the bank switch I selected. The transmitter will call out "Bank 1" "Bank 2", etc. when I flip the switch but the head speed never changed. Furthermore, the head speed is essentially fixed at 1300 no matter what I try. I am using the governor set up in the Vbar NEO.
I realize this post will require me to provide additional information so please don't hesitate to ask.
Thanks for the help.
Nick
RV
4 June 2017 08:3504.06.2017 08:35
Can you please attach the current setup file and eventlog from the last flight (with the HS switches)?
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Bell407
5 June 2017 04:3105.06.2017 04:31
Hello Rainer,
The forum won't allow me to attach files for some reason. I am trying to attach them as PDF but it just won't allow me to do so. I have the current log file ready to send if you can provide me with another mechanism for doing so.
As far as the setup file is concerned, I am not familiar with which file that is. I assume it is located on my PC's I:drive. I attached a screen shot with all the files. Perhaps you can let me know which file it is.
Thanks
RV
5 June 2017 10:3405.06.2017 10:34
OK - please wait, uli will check uploads
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Edited 1 time(s). Last edit at 06/05/2017 10:34AM by RV.
Bell407
5 June 2017 13:0505.06.2017 13:05
Hello Rainer,
Is there an email address I can send the files to?
If you would like to contact me directly I can provide my phone number to you.
Regards,
Nick
RV
5 June 2017 20:5405.06.2017 20:54
Well - i have a mail adress - but phone support is done by Eddi (for me personally it is not the main job).
So - if you want to share the info - use vstabi (at) mikado-heli.de
If you are asking for a call tomorrow - use service (at) mikado-heli.de
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
RV
9 June 2017 20:5009.06.2017 20:50
Ok - the log is here - but the setup missing. Sorry for delay ;-(
Save setup file:
- connect all, start software
- select file/save in pc soft
- save somewhere (maybe the folder where the log is sotred too)
- zip it
- attach here (now enabled)
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Bell407
20 June 2017 04:1920.06.2017 04:19
Rainer,
The forum still won't allow me to attach a file. Will send in email.
Thanks
Nick Shepler
Attachments:
open |
download -
Logo 700 Setup.zip
(7.4 KB)
Bell407
20 June 2017 13:3520.06.2017 13:35
Hello Rainer,
Please forgive me. It appears the file I claimed wouldn't attach to the forum posting actually did attach!!! See my previous message.
Thanks for your help!
Nick
RV
21 June 2017 06:2521.06.2017 06:25
Hello Nick,
you have attached a scorpion log (0071_sco.csv) file - but not the setup files and event logs we need.
Please have a look on your VBC in the /log folder - tere must be a second file from this flight. Also save the setup from the heli to VBC - and then you have the setup file in the /vbar folder too.
regards (EN) / Gruss (DE)
Rainer Vetter
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Posting and answering - please use a PC and a standard keyboard. Answer all questions fully, take the needed time, don't forget probably requested attachments.
Für Posts und Antworten bitte einen PC und eine richtige Taststaur benutzen sowie alle Fragen vollständig abarbeiten. Nehmt Euch Zeit, beantwortet Rückfragen in Ruhe und vollständig.
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
Für Einzelkommunikation bitte ausschließlich Email verwenden! - PN, Messenger, Chat usw. werden nicht bearbeitet.
For single user communication please send a email only! PM, Messenger, Chat etc. won't be read.
Bell407
23 June 2017 13:5023.06.2017 13:50
Hello Rainer,
I apologize for how long it has taken to resolve this issue. Attached is the second file you were referring to.
In regards to the "setup file" you are asking for, I simply do not understand where this file is located, its name, its type (csv, xls, gif, tif, bmp, jpg, etc.). I desperately need your help to understand this. I powered up my VBC and helicopter then plugged the USB cable to the VBC and computer. At that moment I get a series of files and folder pop up on my desktop, none of which resembles anything like a "setup file".
Please help me understand this. Please tell me what the file is, how to get to it, etc. Even a screen shot on your computer or a thorough list of instructions would be wonderful. I am quite frustrated as my helicopter has never been able to change head speeds from 1200 rpm since I got it set up. Don't get me wrong, it flies beautifully! I love it. I just want to get this figured out.
Thanks
Eddi E. aus G.
23 June 2017 14:3123.06.2017 14:31
Hi,
here's what you are looking for (at the bottom of the page).
Same text as in the printed manual ;-)
If you save the file using the Load/Save dialog, it will be named, and you find the file in the folder /vbar on your radio, e.g. for sending it.
Kind regards
Eddi
Born to fly ...
forced to work.
Bell407
24 June 2017 21:1624.06.2017 21:16
Hello Eddi,
Thanks for the response. I was able to find the "Save/Load Setup" in the Vbar Control. However, there really is no option where I can see for actually saving the setup file. When I look in a folder labelled Logo 700 on my PC there are a number of vbar log files (from each flight) as well as the "sco.csv" files for the scorpion ESC.
What is the name of the file I am looking for and what type of file is it? Furthermore where should I go to find it? Additionally, I am not sure what is going on with the forum but I am not able to upload a zip file. It worked once before but not this last time.
Thanks
Eddi E. aus G.
26 June 2017 09:2226.06.2017 09:22
Hi Nick,
it should look this way (where the thunder650 file is the setup, they have no extension any more with VBar Control).
After saving it, it's in the folder /vbar (root of VBar Control/vbar) as written above ;-)
On this board, gif, jpg, png, pdf, zip, vbr should work unless they are larger than 300 KB.
Kind regards
Eddi
Born to fly ...
forced to work.
Bell407
26 June 2017 15:2926.06.2017 15:29
Hi Eddi,
Thanks for the reply. Let's give this a try. Hopefully this is what we are looking for.
Thanks
Bell407
26 June 2017 15:3226.06.2017 15:32
Hi Eddi,
For some reason the forum is not allowing me to attach a zip file with the setup information. The file size is 494 bytes.
Any suggestions?
Thanks
Eddi E. aus G.
27 June 2017 08:5727.06.2017 08:57
Hi,
from my end, no. The admin would have to look into it ... could be something with permissions, as you can see it works from my end.
You can send an e-mail to service (at) mikado-heli (dot) de instead, and refer to this thread.
Kind regards
Eddi
Born to fly ...
forced to work.
Attachments:
open |
download -
logo-neo-11-6-17.zip
(2.1 KB)
Bell407
8 July 2017 15:1008.07.2017 15:10
Hi Ed,
This is a classic example of "egg on my face"!
I am pretty sure I owe the folks at Mikado an apology (that includes yourself, Uli, & Ron Thomas). While at lunch yesterday I watched the Kyle Dahl video you sent me the link to and low and behold I caught something very subtle that Kyle said. He was going thru the wiring installation of the Tribunus back to the NEO and I overheard him say something like, "...and then plug the slave wire from the Tribunus into the RPM port on the NEO". I replayed that again and immediately thought to myself, "I don't think I did that"!!
Prior to leaving work yesterday I had a brief chat with Ron and mentioned to him the possibility that I have the slave wire plugged into one of the Aux ports on the NEO and that I would check it when I got home. Upon returning home I looked at my Logo and sure enough it was plugged into Aux 2. I swapped it over to the RPM port, took the blades off, made sure the banks were at 1000, 1500, & 2000 respectively and ran the test. End result everything works perfectly!!!
The only reason I can possibly think of as to why I had the slave wire plugged into an Aux port from the beginning was I simply thought it was a "back up" source of communication for the Tribunus in the event the Master failed. Furthermore, I was following the Tribunus instructions, which includes a color diagram for the wiring layout, and it shows to connect the slave wire to an external governor/additional BEC voltage wire. It didn't register with me until after watching Kyle's video since I am running the VBar governor on the NEO the RPM signal communication between the NEO and Tribunus must be in place, i.e. thru the slave cable. Perhaps if I was using the Tribunus as the governor it wouldn't have mattered where I plugged the slave wire in (I don't know about that).
At the end of the day, that subtle statement Kyle made in the video regarding the slave wire into the RPM slot on the NEO is what caught my attention. I sent a text to Ron letting him know that fixed it.
For what it's worth, I am very much a sport flyer and don't (can't) do any 3D. Sounds boring right? Well, to me I love to fly the Logo like a real helicopter (scale like). The older club members love it because I fly the pattern with them in their airplanes and not in the middle of the runway doing 3D. Don't get me wrong, the 3D stuff is amazing but for some reason my brain doesn't compute on that level! LOL
My goal during the switch over to electric was to maximize flight time. I run Pulse 6000-12S LiPo in my Logo 700. Couple that with my very smooth, relaxed flying style, as well as a low head speed (1000-1200 rpm), and I am easily getting 20 minutes of flight time (yes 20 minutes!). It is unbelievable! My Logo is incredibly smooth and so easy to fly. I realize I am doing it a huge disservice as compared to all the crazy 3D pilots in the world but I love to represent the opposite side of the flying spectrum. It's great to know my Logo can do anything a competent pilot can throw at it but for me it's all about mimicking the real thing.
Thanks again for all your help. Please feel free to share this with the other folks at Mikado if you like.
Best regards,
Nick
Eddi E. aus G.
19 July 2017 08:5919.07.2017 08:59
Hi Nick,
than you for the insights and your comments :-)
I also prefer the smoother style of flying, with a couple of 2.5 D in it ;-) and I also fly a scale machine. So it' imo certainly not boring and you don't have to feel abashed if you don't do what the young folks do. I find the hobby has so many aspects, and if it's getting the maximum flight time and above all, if _you_ enjoying at the same time, all is well. And then some ;-)
Best,
Eddi
Born to fly ...
forced to work.